[Allstar Digital] Starting on DMRlink

[Michael Hebert]

Thanks Mike!

I am planning to run everything on 1 RPi. So I am assuming that I would use
127.0.0.1 for the ip addresses??

Michael KD5DFB

On Sat, Dec 12, 2015 at 9:47 AM, Mike Zingman <mike.zingman at gmail.com>
wrote:

> Michael,
>
> Sorry for the lack of comments in the file (it was taken from my Allstar
> node).
>
> You should find this diagram useful:
> https://github.com/N4IRS/DMRGateway/blob/master/DMRGateway.pdf
>
> *ambe_audio.cfg:*
> _gateway                    ; IP address of DMRGateway application
> _gateway_port               ; UDP port of DMRGateway listener
> _remote_control_port        ; UDP command port (will be used to adjust
> ambe_audio.py parameters from ASL)
>
> *DMRGateway.ini:*
> [AMBE_AUDIO]
> server and port             ; UDP address of ambe_audio.py
> [USRP]
> server and port             ; UDP address of USRP (asterisk server address)
>
> *rpt.conf :*
>
> rxchannel = usrp/XX.XX.XX.XX:YYYY:ZZZZ
>
> Where XX.XX.XX.XX is the UDP address of DMRGateway application
>
> YYYY is the transmit port (USRP ---->>>> DMRGateway)
>
> ZZZZ is the receive port (DMRGateway ------->>>> USRP)
>
>
> Hope this helps
>
> Mike
>
>
> On Sat, Dec 12, 2015 at 12:08 AM, Michael Hebert <mhebert1975 at gmail.com>
> wrote:
>
>> Mike,
>>
>> In your rxchannel stanza, is 192.168.1.182:34001:32001 the IP address of
>> your RPi? is 34001 and 32001 the tx and rx ports going to the DV3000 dongle?
>>
>> Also, I notice when I run help in asterisk, usrp show is there.
>>
>> Here is what mine shows.
>>
>> 192.168.1.182:34001 txkey no  rxkey 0 read 0 write 0
>>
>> Waiting on DV3000 to show up.
>>
>> Last, in the rpt.conf is that the minimum or the only statements you need?
>>
>>
>> Michael KD5DFB
>>
>> On Fri, Dec 11, 2015 at 12:03 PM, Mike Zingman <mike.zingman at gmail.com>
>> wrote:
>>
>>> 1) in /etc/asterisk/modules.conf enable usrp as
>>>
>>> load => chan_usrp.so
>>>
>>> 2) in rpt.conf create a stanza like:
>>>
>>> [1999]
>>>
>>> rxchannel = usrp/192.168.1.182:34001:32001
>>>
>>> duplex = 2
>>>
>>> scheduler=scheduler
>>>
>>> functions = functions-repeater
>>>
>>> hangtime=0
>>>
>>> authlevel = 0
>>>
>>>
>>> Where the address and ports are configured to your network.
>>>
>>> 3) in rpt.conf add your node
>>>
>>> [nodes]
>>>
>>> 1999 = radio at 127.0.0.1:4570/1999,NONE
>>>
>>>
>>> Now chan_usrp is ready to go.
>>>
>>> On Fri, Dec 11, 2015 at 12:56 PM, David KE6UPI <dshaw at ke6upi.com> wrote:
>>>
>>>> Hello Robert, If you find out how to configure the Chan_USRP and
>>>> asterisk please let me know.
>>>>
>>>> David
>>>>
>>>> On Fri, Dec 11, 2015 at 9:28 AM, Robert Newberry <N1XBM at amsat.org>
>>>> wrote:
>>>>
>>>>> Is the "readme.md" the documentation I should be reading for setting
>>>>> up DMRlink?
>>>>>
>>>>> I've also been scanning dmrlink_SAMPLE.cfg for how to setup a parrot
>>>>> tg.
>>>>>
>>>>> Thank you
>>>>>
>>>>> N1XBM
>>>>> Apparare Scientor
>>>>> Paratus Communicare
>>>>> Allstar Node # 27086, 41540, 41812, 42086, 42658
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Allstar-Digital mailing list
>>>>> Allstar-Digital at lists.keekles.org
>>>>> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>>>>>
>>>>>
>>>>
>>>> _______________________________________________
>>>> Allstar-Digital mailing list
>>>> Allstar-Digital at lists.keekles.org
>>>> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>>>>
>>>>
>>>
>>> _______________________________________________
>>> Allstar-Digital mailing list
>>> Allstar-Digital at lists.keekles.org
>>> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>>>
>>>
>>
>> _______________________________________________
>> Allstar-Digital mailing list
>> Allstar-Digital at lists.keekles.org
>> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>>
>>
>
> _______________________________________________
> Allstar-Digital mailing list
> Allstar-Digital at lists.keekles.org
> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/allstar-digital/attachments/20151212/37246350/attachment.html>