[App_rpt] Getting app_rpt base node to work.

Shane Burrell shaneb at metrostat.net
Fri Jul 21 23:20:14 UTC 2006 

It does light the red light.

-----Original Message-----
From: app_rpt-bounces at lists.illiana.net
[mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of
hwstar at rodgers.sdcoxmail.com
Sent: Friday, July 21, 2006 6:29 PM
To: Asterisk Repeater Controler
Subject: Re: [App_rpt] Getting app_rpt base node to work.

Swap the jacks and tell me if you get a red tx light. Connecting the RX into
the TX port on the ARIB should light the TX LED.

>From what I can deduce, it looks like the modular cables from your channel
bank  are flipping the polarity of tip and ring. The ARIB is polarity
sensitive and will do exactly what you have described if the polarity is
wrong.

Make up a new set of modular cables which swap the red and green wires in
the opposite manner to the cables you are currently using.

Steve.


> 
> From: "Shane Burrell" <shaneb at metrostat.net>
> Date: 2006/07/21 Fri PM 01:08:42 PDT
> To: "'Asterisk Repeater Controler'" <app_rpt at lists.illiana.net>
> Subject: Re: [App_rpt] Getting app_rpt base node to work.
> 
> Now that I have rpt loading I can't seem to figure out how to get the base
> to key up.  I think I have a combo of problems with my config and ARIB
> interface.  
> 
> I have a Sangoma A104D with second T1 channels 1 and two configured.  One
is
> LS other is GS. The goto a TA 750 into the ARIB.  I have set to 4W and
> jumpers 1 and 2 removed.  The ARIB is connected to the KCT-19 pigtal on my
> Kenwood TK-880. I see the COR light come on when I receive a transmission.
> So far so good.  
> 
> When I setup a exten to rpt|P it just gets dead air and doesn't transmit.
I
> assumed that at this point I could dial *X out of the function list and
have
> it do something but it doesn't.  Also no audio occurs on the phone if the
> radio is receiving but the COR light does work.
> 
> Any pointers or next step?  I've dug thru the docs and most of what I see
is
> for repeaters.  I just want to hit a base and send some tones. Maybe an
> annoucment or two.
> 
> TIA,
> 
> SHane
> 
> 
> 
> 
> 
> -----Original Message-----
> From: app_rpt-bounces at lists.illiana.net
> [mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of Shane Burrell
> Sent: Friday, July 21, 2006 1:48 PM
> To: 'Asterisk Repeater Controler'
> Subject: Re: [App_rpt] Getting app_rpt base node to work.
> 
> I figured out I have to restart asterisk.  Now I get dial and get blank
air.
> My goal is to dial a number and have it send out some 2 tone.  I would
> settle for DTMF.  Is there a DTMF command I need to issue to take over/PTT
> the base?
> 
> -----Original Message-----
> From: app_rpt-bounces at lists.illiana.net
> [mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of Jim Duuuude
> Sent: Friday, July 21, 2006 1:43 PM
> To: app_rpt at lists.illiana.net
> Subject: Re: [App_rpt] Getting app_rpt base node to work.
> 
> How about remote=y
> 
> It doesnt recognize remote=dump, and thinks it a node
> and wants an idrecording specified.
> 
> 
> >From: "Shane Burrell" <shaneb at metrostat.net>
> >Reply-To: Asterisk Repeater Controler <app_rpt at lists.illiana.net>
> >To: "'Asterisk Repeater Controler'" <app_rpt at lists.illiana.net>
> >Subject: Re: [App_rpt] Getting app_rpt base node to work.
> >Date: Fri, 21 Jul 2006 13:24:34 -0400
> >MIME-Version: 1.0
> >Received: from lists.illiana.net ([207.227.243.140]) by 
> >bay0-mc8-f19.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2444); Fri,

> >21 Jul 2006 10:24:41 -0700
> >Received: (qmail 3845 invoked from network); 21 Jul 2006 17:24:40 -0000
> >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1)  by 0 with SMTP;
21
> 
> >Jul 2006 17:24:40 -0000
> >Received: (qmail 3828 invoked from network); 21 Jul 2006 17:24:37 -0000
> >Received: from mail.metrostat.net (HELO mx1.metrostat.net)
(152.53.16.15)by
> 
> >0 with SMTP; 21 Jul 2006 17:24:37 -0000
> >Received: by mx1.metrostat.net (Postfix, from userid 1003)id
2FB4F26900CC; 
> >Fri, 21 Jul 2006 13:24:20 -0400 (EDT)
> >Received: from compmst (unknown [152.53.16.10])by mx1.metrostat.net 
> >(Postfix) with ESMTP id D42CD26900BBfor <app_rpt at lists.illiana.net>; Fri,

> >21 Jul 2006 13:24:16 -0400 (EDT)
> >X-Message-Info: LsUYwwHHNt3NYSfb1sbees3Ik0t50SZpLw6VgEAXI2s=
> >Return-Path: <shaneb at metrostat.net>
> >Delivered-To: mailman-app_rpt at lists.illiana.net
> >X-Spam-Checker-Version: SpamAssassin 3.1.0 (2005-09-13) on 
> >mx1.metrostat.net
> >X-Spam-Level: X-Spam-Status: No, score=0.0 required=5.5 tests=none 
> >autolearn=disabled version=3.1.0
> >X-Mailer: Microsoft Office Outlook 11
> >Thread-Index: Acas6IDNhxKN9qu6Qai9iAm0lrd/ggAAdqzw
> >X-MimeOLE: Produced By Microsoft MimeOLE V6.00.2900.2869
> >X-BeenThere: app_rpt at lists.illiana.net
> >X-Mailman-Version: 2.1.6
> >Precedence: list
> >List-Id: Asterisk Repeater Controler <app_rpt.lists.illiana.net>
> >List-Unsubscribe: 
>
><http://lists.illiana.net/mailman/listinfo/app_rpt>,<mailto:app_rpt-request
> @lists.illiana.net?subject=unsubscribe>
> >List-Archive: <http://lists.illiana.net/pipermail/app_rpt>
> >List-Post: <mailto:app_rpt at lists.illiana.net>
> >List-Help: <mailto:app_rpt-request at lists.illiana.net?subject=help>
> >List-Subscribe: 
>
><http://lists.illiana.net/mailman/listinfo/app_rpt>,<mailto:app_rpt-request
> @lists.illiana.net?subject=subscribe>
> >Errors-To: app_rpt-bounces at lists.illiana.net
> >X-OriginalArrivalTime: 21 Jul 2006 17:24:41.0409 (UTC) 
> >FILETIME=[8CF8FB10:01C6ACEA]
> >
> >Still get rpt_exec: Cannot find specified system node 101.  my rpt.conf
is
> >as follows:
> >
> >[101]					; Node ID of remote base
> >rxchannel = Zap/25			; Rx audio/signalling channel
> >txchannel = Zap/26			; Tx audio/signalling channel
> >functions = functions-remote
> >remote = dumb				; Set remote=y for dumb
remote or
> >					; remote=rbi for Doug Hall RBI1
> >[functions-remote]
> >0=remote,1				; Retrieve Memory
> >1=remote,2				; Set freq.
> >2=remote,3				; Set Rx PL tone.
> >40=remote,100				; Rx PL off
> >41=remote,101				; Rx PL on
> >42=remote,102				; Tx PL off
> >43=remote,103				; Tx PL on
> >44=remote,104				; Low Pwr
> >45=remote,105				; Med Pwr
> >46=remote,106				; Hi Pwr
> >5=remote,5				; Status
> >
> >[telemetry]
> >
> >
> >ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
> >ct2=|t(660,880,150,2048)
> >ct3=|t(440,0,150,2048)
> >ct4=|t(550,0,150,2048)
> >ct5=|t(660,0,150,2048)
> >ct6=|t(880,0,150,2048)
> >ct7=|t(660,440,150,2048)
> >ct8=|t(700,1100,150,2048)
> >remotetx=|t(2000,0,75,2048)(0,0,75,0)(1600,0,75,2048);
> >remotemon=|t(1600,0,75,2048)
> >cmdmode=|t(900,903,200,2048)
> >functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> >
> >[morse]
> >speed=20		; Approximate speed in WPM
> >frequency=800		; Morse Telemetry Frequency
> >amplitude=4096		; Morse Telemetry Amplitude
> >idfrequency=330		; Morse ID Frequency
> >idamplitude=2048	; Morse ID Amplitude
> >
> >[nodes]
> >
> >;000 = context_A at 1.2.3.4/1234
> >101 = radio at me.asterisk.net/101
> >
> >;of course, you can also specify these with domain names, but why rely
> >;on DNS working unnecessarily?
> >
> >[memory]
> >
> >;; this example gives you 146.460, simplex, 100.0 HZ PL, hi-power,
transmit
> >PL
> >00 = 146.460,100.0,sht
> >;; this example gives you 146.940, minus offset, 100.0 HZ PL, low-power,
no
> >PL
> >01 = 146.940,100.0,-l
> >
> >; The format for these entries is:  Receive-Freq,Receive-PL,Attrbutes
> >;     Attributes: l=low power, m=medium power, h=high power, -=minus 
> >offset,
> >;	s=simplex, +=plus offset, t=tx PL enable, r=rx PL enable
> >
> >
> >-----Original Message-----
> >From: app_rpt-bounces at lists.illiana.net
> >[mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of
> >hwstar at rodgers.sdcoxmail.com
> >Sent: Friday, July 21, 2006 1:10 PM
> >To: Asterisk Repeater Controler
> >Subject: Re: [App_rpt] Getting app_rpt base node to work.
> >
> >Shane,
> >
> >
> >1. Node numbers with leading zeroes are reserved. Try using 101 instead.
> >
> >2. The node number needs to be defined in 2 places in the rpt.conf file.
> >Once in the repeater section with square brackets e.g. [101] and once in 
> >the
> >[NODES] section as an entry to connect to/from:
> >
> >radio at 127.0.0.1/101,127.0.0.1
> >
> >
> >Steve.
> >
> > >
> > > From: "Shane Burrell" <shaneb at metrostat.net>
> > > Date: 2006/07/21 Fri AM 10:04:30 PDT
> > > To: <app_rpt at lists.illiana.net>
> > > Subject: [App_rpt] Getting app_rpt base node to work.
> > >
> > > I've tried to setup a base node using a kenwood TK-880 and analog
radio
> > > board.  Asterisk reports that rpt_exec: Cannot find specified system 
> >node
> > > 001.  I have 001 defined using the example base node.  Is there 
> >something
> >I
> > > am missing.  Does app-rpt require more than a reload to get its
> > > configuration?
> > >
> > >
> > >
> > > Regards,
> > >
> > >
> > >
> > >
> > >
> > > Shane
> > >
> > >
> > >
> > >
> > >
> >
> >_______________________________________________
> >App_rpt mailing list
> >App_rpt at lists.illiana.net
> >http://lists.illiana.net/mailman/listinfo/app_rpt
> 
> 
> _______________________________________________
> App_rpt mailing list
> App_rpt at lists.illiana.net
> http://lists.illiana.net/mailman/listinfo/app_rpt
> 
> _______________________________________________
> App_rpt mailing list
> App_rpt at lists.illiana.net
> http://lists.illiana.net/mailman/listinfo/app_rpt
> 
> _______________________________________________
> App_rpt mailing list
> App_rpt at lists.illiana.net
> http://lists.illiana.net/mailman/listinfo/app_rpt
> 

_______________________________________________
App_rpt mailing list
App_rpt at lists.illiana.net
http://lists.illiana.net/mailman/listinfo/app_rpt

More information about the App_rpt-users mailing list