[App_rpt] Getting app_rpt base node to work.

Steve Rodgers hwstar at rodgers.sdcoxmail.com
Tue Jul 25 01:02:11 UTC 2006 

JP1 and JP2 need to be removed.

Steve.


On Monday 24 July 2006 11:13, Shane Burrell wrote:
> Do I leave J1 jumpers connected for 2W?
>
> -----Original Message-----
> From: app_rpt-bounces at lists.illiana.net
> [mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of Steve Rodgers
> Sent: Friday, July 21, 2006 10:10 PM
> To: Asterisk Repeater Controler
> Subject: Re: [App_rpt] Getting app_rpt base node to work.
>
> Shane,
>
> Since you are running as a half duplex remote base please verify the
> following:
>
> 1. The ARIB card needs to have the 4W/2W switch set to 2W (2 wire).
>
> 2. Only one cable should be connected from the channelbank to the ARIB
> card.
>
> This should go from the port on the channel bank equivalent to Zap/25 to J1
> on the ARIB card.
>
> 3. There should not be a txchannel defined in the nodes section of
> rpt.conf.
>
> 4. Since you are running as a remote base, you must add a 'y' argument to
> the
> end of the node definition, like this: 101 = radio at me.asterisk.net/101,y
>
> 5. /etc/asterisk/zapata.conf should have em_txrx for signalling on Zap/25.
>
> 6. /etc/zaptel.conf should have channel type for Zap/25 set to e&m
>
> If after verifying the above items and you still have problems:
>
>
> 1. The Sangoma T1 card must be able to talk to the channel bank to control
> the
> DPO port operation. We have not tested the Sangoma T1 cards with app_rpt
> and
>
> cannot confirm if they support DPO operation through Zaptel.
>
>
> Steve.
>
> On Friday 21 July 2006 16:20, Shane Burrell wrote:
> > It does light the red light.
> >
> > -----Original Message-----
> > From: app_rpt-bounces at lists.illiana.net
> > [mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of
> > hwstar at rodgers.sdcoxmail.com
> > Sent: Friday, July 21, 2006 6:29 PM
> > To: Asterisk Repeater Controler
> > Subject: Re: [App_rpt] Getting app_rpt base node to work.
> >
> > Swap the jacks and tell me if you get a red tx light. Connecting the RX
> > into the TX port on the ARIB should light the TX LED.
> >
> > >From what I can deduce, it looks like the modular cables from your
>
> channel
>
> > bank  are flipping the polarity of tip and ring. The ARIB is polarity
> > sensitive and will do exactly what you have described if the polarity is
> > wrong.
> >
> > Make up a new set of modular cables which swap the red and green wires in
> > the opposite manner to the cables you are currently using.
> >
> > Steve.
> >
> > > From: "Shane Burrell" <shaneb at metrostat.net>
> > > Date: 2006/07/21 Fri PM 01:08:42 PDT
> > > To: "'Asterisk Repeater Controler'" <app_rpt at lists.illiana.net>
> > > Subject: Re: [App_rpt] Getting app_rpt base node to work.
> > >
> > > Now that I have rpt loading I can't seem to figure out how to get the
> > > base to key up.  I think I have a combo of problems with my config and
> > > ARIB interface.
> > >
> > > I have a Sangoma A104D with second T1 channels 1 and two configured.
>
> One
>
> > is
> >
> > > LS other is GS. The goto a TA 750 into the ARIB.  I have set to 4W and
> > > jumpers 1 and 2 removed.  The ARIB is connected to the KCT-19 pigtal on
> > > my Kenwood TK-880. I see the COR light come on when I receive a
> > > transmission. So far so good.
> > >
> > > When I setup a exten to rpt|P it just gets dead air and doesn't
>
> transmit.
>
> > I
> >
> > > assumed that at this point I could dial *X out of the function list and
> >
> > have
> >
> > > it do something but it doesn't.  Also no audio occurs on the phone if
>
> the
>
> > > radio is receiving but the COR light does work.
> > >
> > > Any pointers or next step?  I've dug thru the docs and most of what I
>
> see
>
> > is
> >
> > > for repeaters.  I just want to hit a base and send some tones. Maybe an
> > > annoucment or two.
> > >
> > > TIA,
> > >
> > > SHane
> > >
> > >
> > >
> > >
> > >
> > > -----Original Message-----
> > > From: app_rpt-bounces at lists.illiana.net
> > > [mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of Shane Burrell
> > > Sent: Friday, July 21, 2006 1:48 PM
> > > To: 'Asterisk Repeater Controler'
> > > Subject: Re: [App_rpt] Getting app_rpt base node to work.
> > >
> > > I figured out I have to restart asterisk.  Now I get dial and get blank
> >
> > air.
> >
> > > My goal is to dial a number and have it send out some 2 tone.  I would
> > > settle for DTMF.  Is there a DTMF command I need to issue to take
> > > over/PTT the base?
> > >
> > > -----Original Message-----
> > > From: app_rpt-bounces at lists.illiana.net
> > > [mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of Jim Duuuude
> > > Sent: Friday, July 21, 2006 1:43 PM
> > > To: app_rpt at lists.illiana.net
> > > Subject: Re: [App_rpt] Getting app_rpt base node to work.
> > >
> > > How about remote=y
> > >
> > > It doesnt recognize remote=dump, and thinks it a node
> > > and wants an idrecording specified.
> > >
> > > >From: "Shane Burrell" <shaneb at metrostat.net>
> > > >Reply-To: Asterisk Repeater Controler <app_rpt at lists.illiana.net>
> > > >To: "'Asterisk Repeater Controler'" <app_rpt at lists.illiana.net>
> > > >Subject: Re: [App_rpt] Getting app_rpt base node to work.
> > > >Date: Fri, 21 Jul 2006 13:24:34 -0400
> > > >MIME-Version: 1.0
> > > >Received: from lists.illiana.net ([207.227.243.140]) by
> > > >bay0-mc8-f19.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2444);
> > > > Fri,
> > > >
> > > >21 Jul 2006 10:24:41 -0700
> > > >Received: (qmail 3845 invoked from network); 21 Jul 2006 17:24:40
> > > > -0000 Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1)  by 0
> > > > with
>
> SMTP;
>
> > 21
> >
> > > >Jul 2006 17:24:40 -0000
> > > >Received: (qmail 3828 invoked from network); 21 Jul 2006 17:24:37
> > > > -0000 Received: from mail.metrostat.net (HELO mx1.metrostat.net)
> >
> > (152.53.16.15)by
> >
> > > >0 with SMTP; 21 Jul 2006 17:24:37 -0000
> > > >Received: by mx1.metrostat.net (Postfix, from userid 1003)id
> >
> > 2FB4F26900CC;
> >
> > > >Fri, 21 Jul 2006 13:24:20 -0400 (EDT)
> > > >Received: from compmst (unknown [152.53.16.10])by mx1.metrostat.net
> > > >(Postfix) with ESMTP id D42CD26900BBfor <app_rpt at lists.illiana.net>;
> > > > Fri,
> > > >
> > > >21 Jul 2006 13:24:16 -0400 (EDT)
> > > >X-Message-Info: LsUYwwHHNt3NYSfb1sbees3Ik0t50SZpLw6VgEAXI2s=
> > > >Return-Path: <shaneb at metrostat.net>
> > > >Delivered-To: mailman-app_rpt at lists.illiana.net
> > > >X-Spam-Checker-Version: SpamAssassin 3.1.0 (2005-09-13) on
> > > >mx1.metrostat.net
> > > >X-Spam-Level: X-Spam-Status: No, score=0.0 required=5.5 tests=none
> > > >autolearn=disabled version=3.1.0
> > > >X-Mailer: Microsoft Office Outlook 11
> > > >Thread-Index: Acas6IDNhxKN9qu6Qai9iAm0lrd/ggAAdqzw
> > > >X-MimeOLE: Produced By Microsoft MimeOLE V6.00.2900.2869
> > > >X-BeenThere: app_rpt at lists.illiana.net
> > > >X-Mailman-Version: 2.1.6
> > > >Precedence: list
> > > >List-Id: Asterisk Repeater Controler <app_rpt.lists.illiana.net>
> > > >List-Unsubscribe:
> >
> ><http://lists.illiana.net/mailman/listinfo/app_rpt>,<mailto:app_rpt-reques
> >
> > >t @lists.illiana.net?subject=unsubscribe>
> > >
> > > >List-Archive: <http://lists.illiana.net/pipermail/app_rpt>
> > > >List-Post: <mailto:app_rpt at lists.illiana.net>
> > > >List-Help: <mailto:app_rpt-request at lists.illiana.net?subject=help>
> > > >List-Subscribe:
> >
> ><http://lists.illiana.net/mailman/listinfo/app_rpt>,<mailto:app_rpt-reques
> >
> > >t @lists.illiana.net?subject=subscribe>
> > >
> > > >Errors-To: app_rpt-bounces at lists.illiana.net
> > > >X-OriginalArrivalTime: 21 Jul 2006 17:24:41.0409 (UTC)
> > > >FILETIME=[8CF8FB10:01C6ACEA]
> > > >
> > > >Still get rpt_exec: Cannot find specified system node 101.  my
> > > > rpt.conf
> >
> > is
> >
> > > >as follows:
> > > >
> > > >[101]					; Node ID of remote base
> > > >rxchannel = Zap/25			; Rx audio/signalling channel
> > > >txchannel = Zap/26			; Tx audio/signalling channel
> > > >functions = functions-remote
> > > >remote = dumb				; Set remote=y for dumb
> >
> > remote or
> >
> > > >					; remote=rbi for Doug Hall RBI1
> > > >[functions-remote]
> > > >0=remote,1				; Retrieve Memory
> > > >1=remote,2				; Set freq.
> > > >2=remote,3				; Set Rx PL tone.
> > > >40=remote,100				; Rx PL off
> > > >41=remote,101				; Rx PL on
> > > >42=remote,102				; Tx PL off
> > > >43=remote,103				; Tx PL on
> > > >44=remote,104				; Low Pwr
> > > >45=remote,105				; Med Pwr
> > > >46=remote,106				; Hi Pwr
> > > >5=remote,5				; Status
> > > >
> > > >[telemetry]
> > > >
> > > >
> > > >ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
> > > >ct2=|t(660,880,150,2048)
> > > >ct3=|t(440,0,150,2048)
> > > >ct4=|t(550,0,150,2048)
> > > >ct5=|t(660,0,150,2048)
> > > >ct6=|t(880,0,150,2048)
> > > >ct7=|t(660,440,150,2048)
> > > >ct8=|t(700,1100,150,2048)
> > > >remotetx=|t(2000,0,75,2048)(0,0,75,0)(1600,0,75,2048);
> > > >remotemon=|t(1600,0,75,2048)
> > > >cmdmode=|t(900,903,200,2048)
> > > >functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> > > >
> > > >[morse]
> > > >speed=20		; Approximate speed in WPM
> > > >frequency=800		; Morse Telemetry Frequency
> > > >amplitude=4096		; Morse Telemetry Amplitude
> > > >idfrequency=330		; Morse ID Frequency
> > > >idamplitude=2048	; Morse ID Amplitude
> > > >
> > > >[nodes]
> > > >
> > > >;000 = context_A at 1.2.3.4/1234
> > > >101 = radio at me.asterisk.net/101
> > > >
> > > >;of course, you can also specify these with domain names, but why rely
> > > >;on DNS working unnecessarily?
> > > >
> > > >[memory]
> > > >
> > > >;; this example gives you 146.460, simplex, 100.0 HZ PL, hi-power,
> >
> > transmit
> >
> > > >PL
> > > >00 = 146.460,100.0,sht
> > > >;; this example gives you 146.940, minus offset, 100.0 HZ PL,
>
> low-power,
>
> > no
> >
> > > >PL
> > > >01 = 146.940,100.0,-l
> > > >
> > > >; The format for these entries is:  Receive-Freq,Receive-PL,Attrbutes
> > > >;     Attributes: l=low power, m=medium power, h=high power, -=minus
> > > >offset,
> > > >;	s=simplex, +=plus offset, t=tx PL enable, r=rx PL enable
> > > >
> > > >
> > > >-----Original Message-----
> > > >From: app_rpt-bounces at lists.illiana.net
> > > >[mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of
> > > >hwstar at rodgers.sdcoxmail.com
> > > >Sent: Friday, July 21, 2006 1:10 PM
> > > >To: Asterisk Repeater Controler
> > > >Subject: Re: [App_rpt] Getting app_rpt base node to work.
> > > >
> > > >Shane,
> > > >
> > > >
> > > >1. Node numbers with leading zeroes are reserved. Try using 101
>
> instead.
>
> > > >2. The node number needs to be defined in 2 places in the rpt.conf
>
> file.
>
> > > >Once in the repeater section with square brackets e.g. [101] and once
>
> in
>
> > > >the
> > > >[NODES] section as an entry to connect to/from:
> > > >
> > > >radio at 127.0.0.1/101,127.0.0.1
> > > >
> > > >
> > > >Steve.
> > > >
> > > > > From: "Shane Burrell" <shaneb at metrostat.net>
> > > > > Date: 2006/07/21 Fri AM 10:04:30 PDT
> > > > > To: <app_rpt at lists.illiana.net>
> > > > > Subject: [App_rpt] Getting app_rpt base node to work.
> > > > >
> > > > > I've tried to setup a base node using a kenwood TK-880 and analog
> >
> > radio
> >
> > > > > board.  Asterisk reports that rpt_exec: Cannot find specified
> > > > > system
> > > >
> > > >node
> > > >
> > > > > 001.  I have 001 defined using the example base node.  Is there
> > > >
> > > >something
> > > >I
> > > >
> > > > > am missing.  Does app-rpt require more than a reload to get its
> > > > > configuration?
> > > > >
> > > > >
> > > > >
> > > > > Regards,
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > Shane
> > > >
> > > >_______________________________________________
> > > >App_rpt mailing list
> > > >App_rpt at lists.illiana.net
> > > >http://lists.illiana.net/mailman/listinfo/app_rpt
> > >
> > > _______________________________________________
> > > App_rpt mailing list
> > > App_rpt at lists.illiana.net
> > > http://lists.illiana.net/mailman/listinfo/app_rpt
> > >
> > > _______________________________________________
> > > App_rpt mailing list
> > > App_rpt at lists.illiana.net
> > > http://lists.illiana.net/mailman/listinfo/app_rpt
> > >
> > > _______________________________________________
> > > App_rpt mailing list
> > > App_rpt at lists.illiana.net
> > > http://lists.illiana.net/mailman/listinfo/app_rpt
> >
> > _______________________________________________
> > App_rpt mailing list
> > App_rpt at lists.illiana.net
> > http://lists.illiana.net/mailman/listinfo/app_rpt
> >
> > _______________________________________________
> > App_rpt mailing list
> > App_rpt at lists.illiana.net
> > http://lists.illiana.net/mailman/listinfo/app_rpt
>
> _______________________________________________
> App_rpt mailing list
> App_rpt at lists.illiana.net
> http://lists.illiana.net/mailman/listinfo/app_rpt
>
> _______________________________________________
> App_rpt mailing list
> App_rpt at lists.illiana.net
> http://lists.illiana.net/mailman/listinfo/app_rpt

More information about the App_rpt-users mailing list