From renato.ornelas at gmail.com Tue Jul 10 12:49:43 2007 From: renato.ornelas at gmail.com (Renato Ornelas) Date: Tue, 10 Jul 2007 09:49:43 -0300 Subject: [App_rpt] Can't monitor on node Message-ID: Hello dear friends! I'm using a PCI Quad Radio card with a Motorola EM400 radio pluged in. I can use a SIP phone to connect to the node (1999) and issue the PTT command (*98) and deactivate it (#). I want to be able to listen to this channel when I dial to the node but when I ask for the Link status (*7), all I receive on the phone and on the remote radio is "node 1999 repeat_only". I tried the duplex=2 option but it didnt work either. Thanks in avance. My rpt.conf: ; ; Your repeater ; [1999] ; Name of First Repeater rxchannel = Zap/1 ; Rx audio/signalling channel ; Note: if you use a unified interface (tx/rx on one channel), only ; specify the rxchannel and the txchannel will be assumed from the rxchannel ;rxnotch=1065,40 ; Notch a particular frequency, depth ; app_rpt must have been compiled with ; the notch option duplex=2 functions=functions ; Repeater Function Table link_functions=link-functions ; Link Function Table phone_functions=functions ; Phone Function table (reverse patch) telemetry=telemetry ; Telemetry descriptions wait_times=wait-times ; Wait times context = radio ; dialing context for phone callerid = "Your Repeater" <6198192562> ; callerid for phone calls idrecording = /etc/asterisk/id ; id recording accountcode=RADIO ; account code (optional) hangtime=100 ; squelch tail hang time (in ms) (optional) totime=180000 ; transmit time-out time (in ms) (optional) idtime=300000 ; id interval time (in ms) (optional) ; The default values for hangtime, time-out time, and id interval time are ; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms) ; respectively politeid=30000 ; time in milliseconds before ID timer ; expires to try and ID in the tail. ; (optional, default is 30000). idtalkover=|iid/r ; Talkover ID (optional) default is none unlinkedct=ct2 ; unlinked courtesy tone (optional) default is none [functions] 1=ilink,1 ; Specific link disconnect 2=ilink,2 ; Specific Link connect - monitor only 3=ilink,3 ; Specific Link connect - transceive 4=ilink,4 ; Enter command mode on a specific link 5=macro,1 ; Command macros (Defined in the macro section) 7=ilink,5 ; Link status 984=ilink,7 ; Last node to key us up 80=status,1 ; System info 81=status,2 ; Time 82=status,3 ; app_rpt.c Version 87=ilink,15 ; Global node query (all nodes in network) 6=autopatchup 0=autopatchdn ; Autopatch down ; Control operator commands 919296=cop,1 ; System warm boot 919297=cop,2 ; System enable 919298=cop,3 ; System disable 99=cop,4 ; Audio test tone 98=cop,6 ; Telephone key PTT [link-functions] 1=ilink,1 ; Specific link disconnect 2=ilink,2 ; Specific Link connect - monitor only 3=ilink,3 ; Specific Link connect - transceive 5=macro,1 ; Command macros (Defined in the macro section) 7=ilink,5 ; Link status 80=status,1 ; System info 81=status,2 ; Time 82=status,3 ; app_rpt.c Version 87=ilink,15 ; Global node query (all nodes in network) 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up 0=autopatchdn ; Autopatch down [nodes] 1999 = radio at 127.0.0.1/1999,NONE ; This must be changed to your node number -------------- next part -------------- An HTML attachment was scrubbed... URL: From telesistant at hotmail.com Tue Jul 10 15:33:55 2007 From: telesistant at hotmail.com (Jim Duuuude) Date: Tue, 10 Jul 2007 08:33:55 -0700 Subject: [App_rpt] Can't monitor on node In-Reply-To: Message-ID: I am not sure what you are trying to accomplish overall. You obviously have the system connected to a standard simplex tranceiver. Dont you want to configure it as a remote base? The configuration you have is for repeaters (generally full-duplex). If you really are setting up a simplex repeater node (kind of contradiction in terms, huh?), you definitely want duplex =0 or 1. 2 is for full duplex RF hardware only. As far as being able to hear what the receiver hears on a phone connection, if you are using the 'P' option on the extension in extensions.conf, and the *98/# PTT works, then you definitely should be able to hear what the receiver is hearing from the phone connection. >From: "Renato Ornelas" >Reply-To: Asterisk Repeater Controler >To: app_rpt at lists.illiana.net >Subject: [App_rpt] Can't monitor on node >Date: Tue, 10 Jul 2007 09:49:43 -0300 >MIME-Version: 1.0 >Received: from marauder.illiana.net ([64.212.212.35]) by >bay0-mc10-f19.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); Tue, >10 Jul 2007 05:50:10 -0700 >Received: (qmail 1910 invoked by uid 1484); 10 Jul 2007 12:50:03 -0000 >Received: from 127.0.0.1 by marauder (envelope-from >, uid 71) with qmail-scanner-2.01 >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.157008 >secs); 10 Jul 2007 12:50:03 -0000 >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; 10 >Jul 2007 12:50:02 -0000 >Received: (qmail 1756 invoked by uid 1484); 10 Jul 2007 12:49:52 -0000 >Received: from 209.85.134.189 by marauder >(envelope-from, uid 71) with qmail-scanner-2.01 >(clamdscan: 0.84/2481. Clear:RC:0(209.85.134.189):. Processed in 0.089493 >secs); 10 Jul 2007 12:49:52 -0000 >Received: from mu-out-0910.google.com (209.85.134.189)by 0 with SMTP; 10 >Jul 2007 12:49:51 -0000 >Received: by mu-out-0910.google.com with SMTP id w9so1002700muefor >; Tue, 10 Jul 2007 05:49:44 -0700 (PDT) >Received: by 10.82.105.13 with SMTP id d13mr9525096buc.1184071783151;Tue, >10 Jul 2007 05:49:43 -0700 (PDT) >Received: by 10.82.111.6 with HTTP; Tue, 10 Jul 2007 05:49:43 -0700 (PDT) >X-Message-Info: >txF49lGdW4246IDWRlqp1gaPMVvfbfR+C1JCtEaOEqDK/VbqIkj7oRzDZzZ+tkD1 >Return-Path: >Delivered-To: mailman-app_rpt at lists.illiana.net >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:mime-version:content-type;b=HkHT2scoLJ/mObAOOmwoip91oUFy/7SCwNfzQcxxMGh+RoYV4Ah4Mi6JJOF3LRZPiTTOK0q3K94BUcNwHtZ9Od2HANlma0kO3SiG7DN8uhgxdi6usvo0DSCFXPd4/VmH7Lr5dhyAt1bBeSaW9FLZrf9NO5s7Nupx35pfrZGhUa4= >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; >s=beta;h=received:message-id:date:from:to:subject:mime-version:content-type;b=bX44u8lQ5ysS/lx+rD/1wRPBkGYQhtN6ebFe01Aoodr1kKKGDQagu5S5ob8jkCfHSIKcRgxYWOHSeunmL/AePXoz+Xm2Tpt8/qvljrSeRHXHg63xI0GU3R9i1Xq/JqlW/23rQ8Mfob2foYNn1QSwYMjqyP48EMvc72PsinP2wmI= >X-BeenThere: app_rpt at lists.illiana.net >X-Mailman-Version: 2.1.6 >Precedence: list >List-Id: Asterisk Repeater Controler >List-Unsubscribe: >, >List-Archive: >List-Post: >List-Help: >List-Subscribe: >, >Errors-To: app_rpt-bounces at lists.illiana.net >X-OriginalArrivalTime: 10 Jul 2007 12:50:10.0962 (UTC) >FILETIME=[DA0DB720:01C7C2F0] > >Hello dear friends! > >I'm using a PCI Quad Radio card with a Motorola EM400 radio pluged in. I >can >use a SIP phone to connect to the node (1999) and issue the PTT command >(*98) and deactivate it (#). I want to be able to listen to this channel >when I dial to the node but when I ask for the Link status (*7), all I >receive on the phone and on the remote radio is "node 1999 repeat_only". I >tried the duplex=2 option but it didnt work either. > >Thanks in avance. > >My rpt.conf: > >; >; Your repeater >; > >[1999] ; Name of First Repeater > >rxchannel = Zap/1 ; Rx audio/signalling channel >; Note: if you use a unified interface (tx/rx on one channel), only >; specify the rxchannel and the txchannel will be assumed from the >rxchannel >;rxnotch=1065,40 ; Notch a particular frequency, >depth > ; app_rpt must have been compiled >with > ; the notch option >duplex=2 >functions=functions ; Repeater Function Table >link_functions=link-functions ; Link Function Table >phone_functions=functions ; Phone Function table (reverse >patch) >telemetry=telemetry ; Telemetry descriptions >wait_times=wait-times ; Wait times >context = radio ; dialing context for phone >callerid = "Your Repeater" <6198192562> ; callerid for phone calls >idrecording = /etc/asterisk/id ; id recording >accountcode=RADIO ; account code (optional) >hangtime=100 ; squelch tail hang time (in ms) >(optional) >totime=180000 ; transmit time-out time (in ms) >(optional) >idtime=300000 ; id interval time (in ms) >(optional) > >; The default values for hangtime, time-out time, and id interval time are >; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms) >; respectively > >politeid=30000 ; time in milliseconds before ID >timer > ; expires to try and ID in the >tail. > ; (optional, default is 30000). >idtalkover=|iid/r ; Talkover ID (optional) default is >none >unlinkedct=ct2 ; unlinked courtesy tone (optional) >default is none > >[functions] >1=ilink,1 ; Specific link disconnect >2=ilink,2 ; Specific Link connect - monitor >only >3=ilink,3 ; Specific Link connect - >transceive >4=ilink,4 ; Enter command mode on a specific >link >5=macro,1 ; Command macros (Defined in the >macro section) >7=ilink,5 ; Link status >984=ilink,7 ; Last node to key us up > >80=status,1 ; System info >81=status,2 ; Time >82=status,3 ; app_rpt.c Version >87=ilink,15 ; Global node query (all nodes in >network) > >6=autopatchup >0=autopatchdn ; Autopatch down > >; Control operator commands > >919296=cop,1 ; System warm boot >919297=cop,2 ; System enable >919298=cop,3 ; System disable >99=cop,4 ; Audio test tone >98=cop,6 ; Telephone key PTT > > > >[link-functions] >1=ilink,1 ; Specific link disconnect >2=ilink,2 ; Specific Link connect - monitor >only >3=ilink,3 ; Specific Link connect - >transceive >5=macro,1 ; Command macros (Defined in the >macro section) >7=ilink,5 ; Link status > >80=status,1 ; System info >81=status,2 ; Time >82=status,3 ; app_rpt.c Version >87=ilink,15 ; Global node query (all nodes in >network) > >6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up >0=autopatchdn ; Autopatch down > >[nodes] >1999 = radio at 127.0.0.1/1999,NONE ; This must be changed to your node >number >_______________________________________________ >App_rpt mailing list >App_rpt at lists.illiana.net >http://lists.illiana.net/mailman/listinfo/app_rpt From renato.ornelas at gmail.com Tue Jul 10 15:57:04 2007 From: renato.ornelas at gmail.com (Renato Ornelas) Date: Tue, 10 Jul 2007 12:57:04 -0300 Subject: [App_rpt] Can't monitor on node In-Reply-To: References: Message-ID: What I need is: 1) I pickup a SIP Phone, dial the node (In my case 305) 2) I hear the radio channel 3) If i want to speak on the radio, I dial *98 (so i "press" PTT) 3.1) I press # to stop talking I can execute steps 1, 3 and 3.1. I really need to listen what the radio connected on the Quad PCI is receiving. Thanks, Renato 2007/7/10, Jim Duuuude : > > I am not sure what you are trying to accomplish overall. You obviously > have > the system > connected to a standard simplex tranceiver. Dont you want to configure it > as > a remote base? > The configuration you have is for repeaters (generally full-duplex). > > If you really are setting up a simplex repeater node (kind of > contradiction > in terms, huh?), you > definitely want duplex =0 or 1. 2 is for full duplex RF hardware only. > > As far as being able to hear what the receiver hears on a phone > connection, > if you are using > the 'P' option on the extension in extensions.conf, and the *98/# PTT > works, > then you > definitely should be able to hear what the receiver is hearing from the > phone connection. > > > >From: "Renato Ornelas" > >Reply-To: Asterisk Repeater Controler > >To: app_rpt at lists.illiana.net > >Subject: [App_rpt] Can't monitor on node > >Date: Tue, 10 Jul 2007 09:49:43 -0300 > >MIME-Version: 1.0 > >Received: from marauder.illiana.net ([64.212.212.35]) by > >bay0-mc10-f19.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); > Tue, > >10 Jul 2007 05:50:10 -0700 > >Received: (qmail 1910 invoked by uid 1484); 10 Jul 2007 12:50:03 -0000 > >Received: from 127.0.0.1 by marauder (envelope-from > >, uid 71) with qmail-scanner-2.01 > >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.157008 > >secs); 10 Jul 2007 12:50:03 -0000 > >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; > 10 > >Jul 2007 12:50:02 -0000 > >Received: (qmail 1756 invoked by uid 1484); 10 Jul 2007 12:49:52 -0000 > >Received: from 209.85.134.189 by marauder > >(envelope-from, uid 71) with qmail-scanner-2.01 > >(clamdscan: 0.84/2481. Clear:RC:0(209.85.134.189):. Processed in > 0.089493 > >secs); 10 Jul 2007 12:49:52 -0000 > >Received: from mu-out-0910.google.com (209.85.134.189)by 0 with SMTP; 10 > >Jul 2007 12:49:51 -0000 > >Received: by mu-out-0910.google.com with SMTP id w9so1002700muefor > >; Tue, 10 Jul 2007 05:49:44 -0700 (PDT) > >Received: by 10.82.105.13 with SMTP id d13mr9525096buc.1184071783151;Tue, > >10 Jul 2007 05:49:43 -0700 (PDT) > >Received: by 10.82.111.6 with HTTP; Tue, 10 Jul 2007 05:49:43 -0700 (PDT) > >X-Message-Info: > >txF49lGdW4246IDWRlqp1gaPMVvfbfR+C1JCtEaOEqDK/VbqIkj7oRzDZzZ+tkD1 > >Return-Path: > >Delivered-To: mailman-app_rpt at lists.illiana.net > >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; > > >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:mime-version:content-type;b=HkHT2scoLJ/mObAOOmwoip91oUFy/7SCwNfzQcxxMGh+RoYV4Ah4Mi6JJOF3LRZPiTTOK0q3K94BUcNwHtZ9Od2HANlma0kO3SiG7DN8uhgxdi6usvo0DSCFXPd4/VmH7Lr5dhyAt1bBeSaW9FLZrf9NO5s7Nupx35pfrZGhUa4= > >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; > > >s=beta;h=received:message-id:date:from:to:subject:mime-version:content-type;b=bX44u8lQ5ysS/lx+rD/1wRPBkGYQhtN6ebFe01Aoodr1kKKGDQagu5S5ob8jkCfHSIKcRgxYWOHSeunmL/AePXoz+Xm2Tpt8/qvljrSeRHXHg63xI0GU3R9i1Xq/JqlW/23rQ8Mfob2foYNn1QSwYMjqyP48EMvc72PsinP2wmI= > >X-BeenThere: app_rpt at lists.illiana.net > >X-Mailman-Version: 2.1.6 > >Precedence: list > >List-Id: Asterisk Repeater Controler > >List-Unsubscribe: > >, app_rpt-request at lists.illiana.net?subject=unsubscribe> > >List-Archive: > >List-Post: > >List-Help: > >List-Subscribe: > >, app_rpt-request at lists.illiana.net?subject=subscribe> > >Errors-To: app_rpt-bounces at lists.illiana.net > >X-OriginalArrivalTime: 10 Jul 2007 12:50:10.0962 (UTC) > >FILETIME=[DA0DB720:01C7C2F0] > > > >Hello dear friends! > > > >I'm using a PCI Quad Radio card with a Motorola EM400 radio pluged in. I > >can > >use a SIP phone to connect to the node (1999) and issue the PTT command > >(*98) and deactivate it (#). I want to be able to listen to this channel > >when I dial to the node but when I ask for the Link status (*7), all I > >receive on the phone and on the remote radio is "node 1999 repeat_only". > I > >tried the duplex=2 option but it didnt work either. > > > >Thanks in avance. > > > >My rpt.conf: > > > >; > >; Your repeater > >; > > > >[1999] ; Name of First Repeater > > > >rxchannel = Zap/1 ; Rx audio/signalling channel > >; Note: if you use a unified interface (tx/rx on one channel), only > >; specify the rxchannel and the txchannel will be assumed from the > >rxchannel > >;rxnotch=1065,40 ; Notch a particular frequency, > >depth > > ; app_rpt must have been compiled > >with > > ; the notch option > >duplex=2 > >functions=functions ; Repeater Function Table > >link_functions=link-functions ; Link Function Table > >phone_functions=functions ; Phone Function table (reverse > >patch) > >telemetry=telemetry ; Telemetry descriptions > >wait_times=wait-times ; Wait times > >context = radio ; dialing context for phone > >callerid = "Your Repeater" <6198192562> ; callerid for phone calls > >idrecording = /etc/asterisk/id ; id recording > >accountcode=RADIO ; account code (optional) > >hangtime=100 ; squelch tail hang time (in ms) > >(optional) > >totime=180000 ; transmit time-out time (in ms) > >(optional) > >idtime=300000 ; id interval time (in ms) > >(optional) > > > >; The default values for hangtime, time-out time, and id interval time > are > >; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms) > >; respectively > > > >politeid=30000 ; time in milliseconds before ID > >timer > > ; expires to try and ID in the > >tail. > > ; (optional, default is 30000). > >idtalkover=|iid/r ; Talkover ID (optional) default > is > >none > >unlinkedct=ct2 ; unlinked courtesy tone > (optional) > >default is none > > > >[functions] > >1=ilink,1 ; Specific link disconnect > >2=ilink,2 ; Specific Link connect > - monitor > >only > >3=ilink,3 ; Specific Link connect - > >transceive > >4=ilink,4 ; Enter command mode on a > specific > >link > >5=macro,1 ; Command macros (Defined in the > >macro section) > >7=ilink,5 ; Link status > >984=ilink,7 ; Last node to key us up > > > >80=status,1 ; System info > >81=status,2 ; Time > >82=status,3 ; app_rpt.c Version > >87=ilink,15 ; Global node query (all nodes in > >network) > > > >6=autopatchup > >0=autopatchdn ; Autopatch down > > > >; Control operator commands > > > >919296=cop,1 ; System warm boot > >919297=cop,2 ; System enable > >919298=cop,3 ; System disable > >99=cop,4 ; Audio test tone > >98=cop,6 ; Telephone key PTT > > > > > > > >[link-functions] > >1=ilink,1 ; Specific link disconnect > >2=ilink,2 ; Specific Link connect > - monitor > >only > >3=ilink,3 ; Specific Link connect - > >transceive > >5=macro,1 ; Command macros (Defined in the > >macro section) > >7=ilink,5 ; Link status > > > >80=status,1 ; System info > >81=status,2 ; Time > >82=status,3 ; app_rpt.c Version > >87=ilink,15 ; Global node query (all nodes in > >network) > > > >6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up > >0=autopatchdn ; Autopatch down > > > >[nodes] > >1999 = radio at 127.0.0.1/1999,NONE ; This must be changed to your > node > >number > > > >_______________________________________________ > >App_rpt mailing list > >App_rpt at lists.illiana.net > >http://lists.illiana.net/mailman/listinfo/app_rpt > > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt > -------------- next part -------------- An HTML attachment was scrubbed... URL: From hwstar at rodgers.sdcoxmail.com Tue Jul 10 19:36:20 2007 From: hwstar at rodgers.sdcoxmail.com (Stephen Rodgers) Date: Tue, 10 Jul 2007 12:36:20 -0700 Subject: [App_rpt] Can't monitor on node In-Reply-To: References: Message-ID: <4693DFB4.1020101@rodgers.sdcoxmail.com> The problem you are experiencing has nothing to do with link status, or whether the repeater is linked or not. It is most likely a hardware interface or zaptel configuration issue. To hear receive audio, you must make sure you have COR hooked up to the quad radio card. The way to test this is to use another radio to simulate a transmission to the radio connected to the Quad PCI radio card, The green light on the back of tha card should light when a signal is received and go out when the signal goes away. If this is not happening, then this is why you aren't hearing any receive audio. If you are not getting a green light on the card when a signal is received, try the following: 1. With a voltmeter or scope Make sure the COR swings from 0V to greater than 5V or 5V to 0V when a signal is received. 2. Make sure that the ctcss statement(s) are commented out in zaptel.conf like this: #ctcss=1109,2,1109 and that exttone is set to n: exttone=n and that invertcor=y or invertcor=n is set so that the green light comes on when a signal is received and goes out when the signal goes away. Change it to the opposite of what is if the green light is on with no signal and off with a signal. Steve. Renato Ornelas wrote: > Hello dear friends! > > I'm using a PCI Quad Radio card with a Motorola EM400 radio pluged in. I > can > use a SIP phone to connect to the node (1999) and issue the PTT command > (*98) and deactivate it (#). I want to be able to listen to this channel > when I dial to the node but when I ask for the Link status (*7), all I > receive on the phone and on the remote radio is "node 1999 repeat_only". I > tried the duplex=2 option but it didnt work either. > > Thanks in avance. > > My rpt.conf: > > ; > ; Your repeater > ; > > [1999] ; Name of First Repeater > > rxchannel = Zap/1 ; Rx audio/signalling channel > ; Note: if you use a unified interface (tx/rx on one channel), only > ; specify the rxchannel and the txchannel will be assumed from the > rxchannel > ;rxnotch=1065,40 ; Notch a particular frequency, > depth > ; app_rpt must have been compiled > with > ; the notch option > duplex=2 > functions=functions ; Repeater Function Table > link_functions=link-functions ; Link Function Table > phone_functions=functions ; Phone Function table (reverse > patch) > telemetry=telemetry ; Telemetry descriptions > wait_times=wait-times ; Wait times > context = radio ; dialing context for phone > callerid = "Your Repeater" <6198192562> ; callerid for phone calls > idrecording = /etc/asterisk/id ; id recording > accountcode=RADIO ; account code (optional) > hangtime=100 ; squelch tail hang time (in ms) > (optional) > totime=180000 ; transmit time-out time (in ms) > (optional) > idtime=300000 ; id interval time (in ms) > (optional) > > ; The default values for hangtime, time-out time, and id interval time are > ; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms) > ; respectively > > politeid=30000 ; time in milliseconds before ID > timer > ; expires to try and ID in the tail. > ; (optional, default is 30000). > idtalkover=|iid/r ; Talkover ID (optional) default is > none > unlinkedct=ct2 ; unlinked courtesy tone (optional) > default is none > > [functions] > 1=ilink,1 ; Specific link disconnect > 2=ilink,2 ; Specific Link connect - monitor > only > 3=ilink,3 ; Specific Link connect - > transceive > 4=ilink,4 ; Enter command mode on a specific > link > 5=macro,1 ; Command macros (Defined in the > macro section) > 7=ilink,5 ; Link status > 984=ilink,7 ; Last node to key us up > > 80=status,1 ; System info > 81=status,2 ; Time > 82=status,3 ; app_rpt.c Version > 87=ilink,15 ; Global node query (all nodes in > network) > > 6=autopatchup > 0=autopatchdn ; Autopatch down > > ; Control operator commands > > 919296=cop,1 ; System warm boot > 919297=cop,2 ; System enable > 919298=cop,3 ; System disable > 99=cop,4 ; Audio test tone > 98=cop,6 ; Telephone key PTT > > > > [link-functions] > 1=ilink,1 ; Specific link disconnect > 2=ilink,2 ; Specific Link connect - monitor > only > 3=ilink,3 ; Specific Link connect - > transceive > 5=macro,1 ; Command macros (Defined in the > macro section) > 7=ilink,5 ; Link status > > 80=status,1 ; System info > 81=status,2 ; Time > 82=status,3 ; app_rpt.c Version > 87=ilink,15 ; Global node query (all nodes in > network) > > 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up > 0=autopatchdn ; Autopatch down > > [nodes] > 1999 = radio at 127.0.0.1/1999,NONE ; This must be changed to your node > number > > > ------------------------------------------------------------------------ > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt From telesistant at hotmail.com Tue Jul 10 20:04:02 2007 From: telesistant at hotmail.com (Jim Duuuude) Date: Tue, 10 Jul 2007 13:04:02 -0700 Subject: [App_rpt] Can't monitor on node In-Reply-To: Message-ID: then I would definitely say to make it a remote base node. >From: "Renato Ornelas" >Reply-To: Asterisk Repeater Controler >To: "Asterisk Repeater Controler" >Subject: Re: [App_rpt] Can't monitor on node >Date: Tue, 10 Jul 2007 12:57:04 -0300 >MIME-Version: 1.0 >Received: from marauder.illiana.net ([64.212.212.35]) by >bay0-mc7-f18.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); Tue, >10 Jul 2007 08:57:20 -0700 >Received: (qmail 32589 invoked by uid 1484); 10 Jul 2007 15:57:19 -0000 >Received: from 127.0.0.1 by marauder (envelope-from >, uid 71) with qmail-scanner-2.01 >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.222487 >secs); 10 Jul 2007 15:57:19 -0000 >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; 10 >Jul 2007 15:57:18 -0000 >Received: (qmail 32477 invoked by uid 1484); 10 Jul 2007 15:57:11 -0000 >Received: from 66.249.92.174 by marauder >(envelope-from, uid 71) with qmail-scanner-2.01 >(clamdscan: 0.84/2481. Clear:RC:0(66.249.92.174):. Processed in 0.148814 >secs); 10 Jul 2007 15:57:11 -0000 >Received: from ug-out-1314.google.com (66.249.92.174)by 0 with SMTP; 10 Jul >2007 15:57:10 -0000 >Received: by ug-out-1314.google.com with SMTP id 75so1351965ugbfor >; Tue, 10 Jul 2007 08:57:05 -0700 (PDT) >Received: by 10.82.170.2 with SMTP id s2mr9869742bue.1184083024510;Tue, 10 >Jul 2007 08:57:04 -0700 (PDT) >Received: by 10.82.111.6 with HTTP; Tue, 10 Jul 2007 08:57:04 -0700 (PDT) >X-Message-Info: >LsUYwwHHNt3660MmjhEvYg2f34OAemlK+ZzoV09lDsZmbz8QigGIQtU5Yvr3lK0P >Return-Path: >Delivered-To: mailman-app_rpt at lists.illiana.net >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=AEkkdRStFxUgfYR5/UwtZ0ioquOD9ud2J2G9sWflHsFlfWGuwKZ630aWzsQ+JlZ7feDUxCXjSHCBSzRNC06M00bR2I1zMwO1SFWLGwN00997VH0zqEad0MwtMdeqHgqJehjZJ838fzuBa0B4yZkMJg04G+YCnr9XxLCw3MzMLS4= >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; >s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=Y9HTxpdqnw8YfxLp7SSo5A8HuTQnVdgiCrW8awvf+umMWHddYSD6l4M2o3Q7g0n3OISWg8MmizoiwRthWCO+KrogjT+H11yCz/njb42KpHDq0HbFrqjVxU2VuSVI0oEeW2hmYHX5SnMpaJ63HiTS2qYsTGH6GRc5WyHJpPSlg3I= >References: > >X-BeenThere: app_rpt at lists.illiana.net >X-Mailman-Version: 2.1.6 >Precedence: list >List-Id: Asterisk Repeater Controler >List-Unsubscribe: >, >List-Archive: >List-Post: >List-Help: >List-Subscribe: >, >Errors-To: app_rpt-bounces at lists.illiana.net >X-OriginalArrivalTime: 10 Jul 2007 15:57:21.0360 (UTC) >FILETIME=[FFE47500:01C7C30A] > >What I need is: > >1) I pickup a SIP Phone, dial the node (In my case 305) >2) I hear the radio channel >3) If i want to speak on the radio, I dial *98 (so i "press" PTT) >3.1) I press # to stop talking > >I can execute steps 1, 3 and 3.1. > >I really need to listen what the radio connected on the Quad PCI is >receiving. > >Thanks, >Renato > > >2007/7/10, Jim Duuuude : >> >>I am not sure what you are trying to accomplish overall. You obviously >>have >>the system >>connected to a standard simplex tranceiver. Dont you want to configure it >>as >>a remote base? >>The configuration you have is for repeaters (generally full-duplex). >> >>If you really are setting up a simplex repeater node (kind of >>contradiction >>in terms, huh?), you >>definitely want duplex =0 or 1. 2 is for full duplex RF hardware only. >> >>As far as being able to hear what the receiver hears on a phone >>connection, >>if you are using >>the 'P' option on the extension in extensions.conf, and the *98/# PTT >>works, >>then you >>definitely should be able to hear what the receiver is hearing from the >>phone connection. >> >> >> >From: "Renato Ornelas" >> >Reply-To: Asterisk Repeater Controler >> >To: app_rpt at lists.illiana.net >> >Subject: [App_rpt] Can't monitor on node >> >Date: Tue, 10 Jul 2007 09:49:43 -0300 >> >MIME-Version: 1.0 >> >Received: from marauder.illiana.net ([64.212.212.35]) by >> >bay0-mc10-f19.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); >>Tue, >> >10 Jul 2007 05:50:10 -0700 >> >Received: (qmail 1910 invoked by uid 1484); 10 Jul 2007 12:50:03 -0000 >> >Received: from 127.0.0.1 by marauder (envelope-from >> >, uid 71) with qmail-scanner-2.01 >> >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.157008 >> >secs); 10 Jul 2007 12:50:03 -0000 >> >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; >>10 >> >Jul 2007 12:50:02 -0000 >> >Received: (qmail 1756 invoked by uid 1484); 10 Jul 2007 12:49:52 -0000 >> >Received: from 209.85.134.189 by marauder >> >(envelope-from, uid 71) with >>qmail-scanner-2.01 >> >(clamdscan: 0.84/2481. Clear:RC:0(209.85.134.189):. Processed in >>0.089493 >> >secs); 10 Jul 2007 12:49:52 -0000 >> >Received: from mu-out-0910.google.com (209.85.134.189)by 0 with SMTP; 10 >> >Jul 2007 12:49:51 -0000 >> >Received: by mu-out-0910.google.com with SMTP id w9so1002700muefor >> >; Tue, 10 Jul 2007 05:49:44 -0700 (PDT) >> >Received: by 10.82.105.13 with SMTP id >>d13mr9525096buc.1184071783151;Tue, >> >10 Jul 2007 05:49:43 -0700 (PDT) >> >Received: by 10.82.111.6 with HTTP; Tue, 10 Jul 2007 05:49:43 -0700 >>(PDT) >> >X-Message-Info: >> >txF49lGdW4246IDWRlqp1gaPMVvfbfR+C1JCtEaOEqDK/VbqIkj7oRzDZzZ+tkD1 >> >Return-Path: >> >Delivered-To: mailman-app_rpt at lists.illiana.net >> >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; >> >> >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:mime-version:content-type;b=HkHT2scoLJ/mObAOOmwoip91oUFy/7SCwNfzQcxxMGh+RoYV4Ah4Mi6JJOF3LRZPiTTOK0q3K94BUcNwHtZ9Od2HANlma0kO3SiG7DN8uhgxdi6usvo0DSCFXPd4/VmH7Lr5dhyAt1bBeSaW9FLZrf9NO5s7Nupx35pfrZGhUa4= >> >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; >> >> >s=beta;h=received:message-id:date:from:to:subject:mime-version:content-type;b=bX44u8lQ5ysS/lx+rD/1wRPBkGYQhtN6ebFe01Aoodr1kKKGDQagu5S5ob8jkCfHSIKcRgxYWOHSeunmL/AePXoz+Xm2Tpt8/qvljrSeRHXHg63xI0GU3R9i1Xq/JqlW/23rQ8Mfob2foYNn1QSwYMjqyP48EMvc72PsinP2wmI= >> >X-BeenThere: app_rpt at lists.illiana.net >> >X-Mailman-Version: 2.1.6 >> >Precedence: list >> >List-Id: Asterisk Repeater Controler >> >List-Unsubscribe: >> >,>app_rpt-request at lists.illiana.net?subject=unsubscribe> >> >List-Archive: >> >List-Post: >> >List-Help: >> >List-Subscribe: >> >,>app_rpt-request at lists.illiana.net?subject=subscribe> >> >Errors-To: app_rpt-bounces at lists.illiana.net >> >X-OriginalArrivalTime: 10 Jul 2007 12:50:10.0962 (UTC) >> >FILETIME=[DA0DB720:01C7C2F0] >> > >> >Hello dear friends! >> > >> >I'm using a PCI Quad Radio card with a Motorola EM400 radio pluged in. I >> >can >> >use a SIP phone to connect to the node (1999) and issue the PTT command >> >(*98) and deactivate it (#). I want to be able to listen to this channel >> >when I dial to the node but when I ask for the Link status (*7), all I >> >receive on the phone and on the remote radio is "node 1999 repeat_only". >>I >> >tried the duplex=2 option but it didnt work either. >> > >> >Thanks in avance. >> > >> >My rpt.conf: >> > >> >; >> >; Your repeater >> >; >> > >> >[1999] ; Name of First Repeater >> > >> >rxchannel = Zap/1 ; Rx audio/signalling channel >> >; Note: if you use a unified interface (tx/rx on one channel), only >> >; specify the rxchannel and the txchannel will be assumed from the >> >rxchannel >> >;rxnotch=1065,40 ; Notch a particular frequency, >> >depth >> > ; app_rpt must have been >>compiled >> >with >> > ; the notch option >> >duplex=2 >> >functions=functions ; Repeater Function Table >> >link_functions=link-functions ; Link Function Table >> >phone_functions=functions ; Phone Function table (reverse >> >patch) >> >telemetry=telemetry ; Telemetry descriptions >> >wait_times=wait-times ; Wait times >> >context = radio ; dialing context for phone >> >callerid = "Your Repeater" <6198192562> ; callerid for phone calls >> >idrecording = /etc/asterisk/id ; id recording >> >accountcode=RADIO ; account code (optional) >> >hangtime=100 ; squelch tail hang time (in ms) >> >(optional) >> >totime=180000 ; transmit time-out time (in ms) >> >(optional) >> >idtime=300000 ; id interval time (in ms) >> >(optional) >> > >> >; The default values for hangtime, time-out time, and id interval time >>are >> >; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms) >> >; respectively >> > >> >politeid=30000 ; time in milliseconds before ID >> >timer >> > ; expires to try and ID in the >> >tail. >> > ; (optional, default is 30000). >> >idtalkover=|iid/r ; Talkover ID (optional) default >>is >> >none >> >unlinkedct=ct2 ; unlinked courtesy tone >>(optional) >> >default is none >> > >> >[functions] >> >1=ilink,1 ; Specific link disconnect >> >2=ilink,2 ; Specific Link connect >>- monitor >> >only >> >3=ilink,3 ; Specific Link connect - >> >transceive >> >4=ilink,4 ; Enter command mode on a >>specific >> >link >> >5=macro,1 ; Command macros (Defined in the >> >macro section) >> >7=ilink,5 ; Link status >> >984=ilink,7 ; Last node to key us up >> > >> >80=status,1 ; System info >> >81=status,2 ; Time >> >82=status,3 ; app_rpt.c Version >> >87=ilink,15 ; Global node query (all nodes >>in >> >network) >> > >> >6=autopatchup >> >0=autopatchdn ; Autopatch down >> > >> >; Control operator commands >> > >> >919296=cop,1 ; System warm boot >> >919297=cop,2 ; System enable >> >919298=cop,3 ; System disable >> >99=cop,4 ; Audio test tone >> >98=cop,6 ; Telephone key PTT >> > >> > >> > >> >[link-functions] >> >1=ilink,1 ; Specific link disconnect >> >2=ilink,2 ; Specific Link connect >>- monitor >> >only >> >3=ilink,3 ; Specific Link connect - >> >transceive >> >5=macro,1 ; Command macros (Defined in the >> >macro section) >> >7=ilink,5 ; Link status >> > >> >80=status,1 ; System info >> >81=status,2 ; Time >> >82=status,3 ; app_rpt.c Version >> >87=ilink,15 ; Global node query (all nodes >>in >> >network) >> > >> >6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up >> >0=autopatchdn ; Autopatch down >> > >> >[nodes] >> >1999 = radio at 127.0.0.1/1999,NONE ; This must be changed to your >>node >> >number >> >> >> >_______________________________________________ >> >App_rpt mailing list >> >App_rpt at lists.illiana.net >> >http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >>_______________________________________________ >>App_rpt mailing list >>App_rpt at lists.illiana.net >>http://lists.illiana.net/mailman/listinfo/app_rpt >> >_______________________________________________ >App_rpt mailing list >App_rpt at lists.illiana.net >http://lists.illiana.net/mailman/listinfo/app_rpt From w4rfj at arrl.net Sun Jul 15 00:29:16 2007 From: w4rfj at arrl.net (Roger F. Jordan) Date: Sat, 14 Jul 2007 20:29:16 -0400 Subject: [App_rpt] okay I am making progress.... Message-ID: Hi, Just thought I would share my experiences with the group concerning my efforts to get APP_RPT up and running! Sooooo far I have it working.but let me back up a step or two here.. I spent some considerable time looking at distro's. I decided on Fedora Core 7 (has everything). I downloaded all the config files for the repeater and the newer version of app_rpt. then I went thru the process of getting the libpri, zaptel and asterisk files. I used WGET to download the most up to date (As per asterisks web site). Loading and compiling everything went fine until. I went to compile asterisk with the new app_rpt.c file!! To make a long story short. there was an error at MAKE time that stated not to use LOCALTIME_r to use Ast_localtime instead! (OK that blew me away!!!!) soooooo I replaced the newer app_rpt with the original app_rpt. That did the trick. now the compile and makes all worked! And I actually got the machine to repeat and get dial tone. to put it bluntly I had a blast playing with the CONF files and actually proved I could get a repeater up!!! Okay.. Now I am thirsty.. Why would the newer app_rpt not work??? Well I found the localtime_r file and replaced them with the older ones version ast_localtime oh and I had to put a ", NULL" at the end to make it work. Only 2 lines had to be changed. I recompiled asterisk with the new modified app_rpt. and it worked great!! Actually the DTMF command for time works now!! Okay. here is where I can use some help.. I got iaxrpt working with the repeater. and actually have my Microzap td400p board working as 2 separate repeaters that can be linked together or connected to by iaxrpt. But I want a little more.. I would like to know how to set up extensions, external sip devices. and make it so that I can dial into the asterix box and maybe get a digital attendant to give me a list of extensions and even maybe require a dtmf password to connect to either Repeater. or even the ability to connect to another extension. and maybe even a conference.. I am under the impression that this system can do everything except wipe your *((&*(%. I sure could use a hand at understanding how all this can work with a regular phone system! Best Regards, Roger W4RFJ PS. And I could use some help on how to access the AllStar stuff too! ;] -------------- next part -------------- An HTML attachment was scrubbed... URL: From hwstar at rodgers.sdcoxmail.com Sun Jul 15 01:23:02 2007 From: hwstar at rodgers.sdcoxmail.com (Stephen Rodgers) Date: Sat, 14 Jul 2007 18:23:02 -0700 Subject: [App_rpt] okay I am making progress.... In-Reply-To: <20070715002853.EMGY1213.dukecmmtai04.coxmail.com@dukecmimpi01.coxmail.com> References: <20070715002853.EMGY1213.dukecmmtai04.coxmail.com@dukecmimpi01.coxmail.com> Message-ID: <469976F6.9000709@rodgers.sdcoxmail.com> Roger, Glad to see you got it all running! See my responses below. Steve Rodgers, WA6ZFT Roger F. Jordan wrote: > Hi, > > > > Just thought I would share my experiences with the group > concerning my efforts to get APP_RPT up and running! Sooooo far I have it > working.but let me back up a step or two here.. I spent some considerable > time looking at distro's. I decided on Fedora Core 7 (has everything). I > downloaded all the config files for the repeater and the newer version of > app_rpt. then I went thru the process of getting the libpri, zaptel and > asterisk files. I used WGET to download the most up to date (As per > asterisks web site). Loading and compiling everything went fine until. I > went to compile asterisk with the new app_rpt.c file!! To make a long story > short. there was an error at MAKE time that stated not to use LOCALTIME_r to > use > > Ast_localtime instead! (OK that blew me away!!!!) soooooo I replaced the > newer app_rpt with the original app_rpt. That did the trick. now the > compile and makes all worked! And I actually got the machine to repeat and > get dial tone. to put it bluntly I had a blast playing with the CONF files > and actually proved I could get a repeater up!!! > > > > Okay.. Now I am thirsty.. Why would the newer app_rpt not > work??? Well I found the localtime_r file and replaced them with the older > ones version ast_localtime oh and I had to put a ", NULL" at the end to > make it work. Only 2 lines had to be changed. I recompiled asterisk with > the new modified app_rpt. and it worked great!! Actually the DTMF command > for time works now!! There was a reason we didn't use ast_localtime in the past. The time being returned was incorrect; the time was several hours off. What version of asterisk you are using? It sounds like we need to update app_rpt to use ast_localtime selectively based on the version of asterisk being compiled. > > > > Okay. here is where I can use some help.. I got iaxrpt > working with the repeater. and actually have my Microzap td400p board > working as 2 separate repeaters that can be linked together or connected to > by iaxrpt. But I want a little more.. I would like to know how to set > up extensions, external sip devices. and make it so that I can dial into the > asterix box and maybe get a digital attendant to give me a list of > extensions and even maybe require a dtmf password to connect to either > Repeater. or even the ability to connect to another extension. and maybe > even a conference.. There are so many things you can do with Asterisk that you will need to be very specific about what you want to start out with first. I would suggest that you initially keep it simple. Dialing in using a reverse autopatch is probably a good way to start. I can't help you with SIP as I don't have any SIP hardware and have not used it much in the past. This extension logic snippet will add a context in extensions.conf: [radio-control] exten=1999,1,Answer exten=1999,n,Playback,rpt/node exten=1999,n,Playback,digits/1 exten=1999,n,Playback,digits/9 exten=1999,n,Playback,digits/9 exten=1999,n,Playback,digits/9 exten=1999,n,Rpt,1999|P In sip.conf you would add a stanza to direct control to radio-control context. For iax.conf which I am more familiar with, it would look like this: [control] type=user context=radio-control auth=md5 secret=gutentag disallow=all allow=gsm transfer=no Take a look at the configuration keywords between iax.conf and sip.conf. Most of them will probably be the same. > > > > I am under the impression that this system can do everything > except wipe your *((&*(%. I sure could use a hand at understanding how all > this can work with a regular phone system! > > > > Best Regards, > > Roger W4RFJ > > > > PS. And I could use some help on how to access the AllStar stuff too! ;] You will need to have a fully qualified domain name (e.g. foo.bar.com) (not a numeric IP address). If your IP address is dynamic, you will need to run a dynamic dns client on your asterisk box. We recommend no-ip.com. You can select a domain name (I like to use the following format for my repeater nodes: w4rfj-yourlocation.sytes.net. I then set the host name on the system to callsign-yourlocation.) You can download the dynamic dns client from no-ip.com. It is a C source file you'll need to compile. Make sure it runs at boot up by executing it in rc.local. Once you have the dynamic dns client running, then go to allstarlink.org and request assignment of a node number. Send me an email once you have done this and I'll process the request for you. Steve. > > > > > > > > > > > ------------------------------------------------------------------------ > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt From w4rfj at arrl.net Sun Jul 15 01:51:43 2007 From: w4rfj at arrl.net (Roger F. Jordan) Date: Sat, 14 Jul 2007 21:51:43 -0400 Subject: [App_rpt] FW: okay I am making progress.... Message-ID: Hi Bill, I am also an auxilliarist! SO-CM, FSO-VFC FSO-MS, FSO-CM 053-04-07 Flotilla 47 Fifth Northern! I will send the conf files as soon as I can get them off of my Linux Box! I think that will be tonight. but I am not sure I will be able to access my XP with the SAMBA Stuff. Do not hold me accountable for the mess they are in. I am still trying to figure this stuff out!! I plan to use the ARIB with my setup! I will also be experimenting with simplex links! I have a ZAPMICRO Board. and it seems to work with the phones I have connected to test with! I also have been testing with the IAXRPT program that runs on winblows! Pretty neat stuff! I will be glad to help as much as I can. boy this asterisk stuff has a steeeeeep learning curve! Best Regards, Roger - W4RFJ Semper Paratus! _____ From: Bill Photinos [mailto:photinos at flotilla57.com] Sent: Saturday, July 14, 2007 9:15 PM To: w4rfj at arrl.net Subject: Re: [App_rpt] okay I am making progress.... Am about to do a setup with a quad-radio card and several repeaters as well. Would it be possible to send me your working config files as a start for me to look at? What kind of setup are you using to interface with the radios? Any help would be greatly appreciated. Thanks, Bill - W4RVN _______________________________________________ App_rpt mailing list App_rpt at lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt -- =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- Bill Photinos U.S.C.G. Auxiliary SO-CM/SO-IS(A)/FSO-CM/FSO-IS 054-05-07 100 Pinewood Road #311 Virginia Beach, VA 23451 (757)313-4877 (757)449-6254(Cell) photinos at flotilla57.com -------------- next part -------------- An HTML attachment was scrubbed... URL: From hwstar at rodgers.sdcoxmail.com Sun Jul 15 02:29:20 2007 From: hwstar at rodgers.sdcoxmail.com (Stephen Rodgers) Date: Sat, 14 Jul 2007 19:29:20 -0700 Subject: [App_rpt] FW: okay I am making progress.... In-Reply-To: <20070715015114.FQCF1228.dukecmmtai03.coxmail.com@dukecmimpi01.coxmail.com> References: <20070715015114.FQCF1228.dukecmmtai03.coxmail.com@dukecmimpi01.coxmail.com> Message-ID: <46998680.3010209@rodgers.sdcoxmail.com> Bill, There are default config files at https://sv.qrvc.com/viewvc/ll_ast/build/configs. Download all of the files in the top directory and all of the files in the pciradio directory. This will enable the first channel on the quad radio card as a repeater. Steve WA6ZFT Roger F. Jordan wrote: > Hi Bill, > > > > I am also an auxilliarist! SO-CM, FSO-VFC FSO-MS, FSO-CM > 053-04-07 Flotilla 47 Fifth Northern! > > I will send the conf files as soon as I can get them off of my Linux Box! I > think that will be tonight. but I am not sure I will be able to access my XP > with the SAMBA Stuff. > > Do not hold me accountable for the mess they are in. I am still trying to > figure this stuff out!! > > > > I plan to use the ARIB with my setup! I will also be > experimenting with simplex links! I have a ZAPMICRO Board. and it seems to > work with the phones I have connected to test with! > > I also have been testing with the IAXRPT program that runs on winblows! > Pretty neat stuff! I will be glad to help as much as I can. boy this > asterisk stuff has a steeeeeep learning curve! > > > > Best Regards, > > Roger - W4RFJ > > > > Semper Paratus! > > > > > > > > _____ > > From: Bill Photinos [mailto:photinos at flotilla57.com] > Sent: Saturday, July 14, 2007 9:15 PM > To: w4rfj at arrl.net > Subject: Re: [App_rpt] okay I am making progress.... > > > > Am about to do a setup with a quad-radio card and several repeaters as well. > Would it be possible to send me your working config files as a start for me > to look at? > > > > > > What kind of setup are you using to interface with the radios? > > > > > > Any help would be greatly appreciated. > > > > > > Thanks, > > > Bill - W4RVN > > > > > > > > > > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt > > > > > > > > > ------------------------------------------------------------------------ > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt From w4rfj at arrl.net Sun Jul 15 02:29:27 2007 From: w4rfj at arrl.net (Roger F. Jordan) Date: Sat, 14 Jul 2007 22:29:27 -0400 Subject: [App_rpt] okay I am making progress.... In-Reply-To: <469976F6.9000709@rodgers.sdcoxmail.com> Message-ID: Hi Steve, Thanks for the quick reply! See My replies below... -----Original Message----- From: app_rpt-bounces at lists.illiana.net [mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of Stephen Rodgers Sent: Saturday, July 14, 2007 9:23 PM To: Asterisk Repeater Controler Subject: Re: [App_rpt] okay I am making progress.... Steve Rodgers, WA6ZFT wrote: >There was a reason we didn't use ast_localtime in the past. The time >being returned was incorrect; the time was several hours off. What >version of asterisk you are using? It sounds like we need to update >app_rpt to use ast_localtime selectively based on the version of >asterisk being compiled. The version is 0.68 - I double checked the time as sent by my system... and it is right on... I plan to get the ntp client going to make it more accurate! I am sending the app_rpt (both original and Modified) so that you may look at it! >There are so many things you can do with Asterisk that you will need to >be very specific about what you want to start out with first. I would >suggest that you initially keep it simple. Dialing in using a reverse >autopatch is probably a good way to start. I can't help you with SIP as >I don't have any SIP hardware and have not used it much in the past. > >This extension logic snippet will add a context in extensions.conf: > >[radio-control] > > > exten=1999,1,Answer > >exten=1999,n,Playback,rpt/node > >exten=1999,n,Playback,digits/1 > >exten=1999,n,Playback,digits/9 > >exten=1999,n,Playback,digits/9 > >exten=1999,n,Playback,digits/9 > >exten=1999,n,Rpt,1999|P > > >In sip.conf you would add a stanza to direct control to radio-control >context. For iax.conf which I am more familiar with, it would look like >this: > >[control] > >type=user >context=radio-control >auth=md5 >secret=gutentag >disallow=all >allow=gsm >transfer=no > >Take a look at the configuration keywords between iax.conf and sip.conf. >Most of them will probably be the same. I understand what you are doing with both files... I am still a little confused about the "context" stuff! I guess the user name in the iax device or pgm would have to be "control" with the password gutentag, right? Well, I will play with it! Thanks for the pointer! >You will need to have a fully qualified domain name (e.g. foo.bar.com) >(not a numeric IP address). If your IP address is dynamic, you will need >to run a dynamic dns client on your asterisk box. We recommend >no-ip.com. You can select a domain name (I like to use the following >format for my repeater nodes: w4rfj-yourlocation.sytes.net. I then set >the host name on the system to callsign-yourlocation.) > >You can download the dynamic dns client from no-ip.com. It is a C source >file you'll need to compile. Make sure it runs at boot up by executing >it in rc.local. > >Once you have the dynamic dns client running, then go to allstarlink.org >and request assignment of a node number. Send me an email once you have >done this and I'll process the request for you. > > >Steve. I have a NODE number assigned already.... My node number is 2057 do you need my password?? I will get the dynamic dns set-up when I get this thing finalized and ready for permanent installation! I still need to get my allowance saved up for the ARIB boards! Also... how would you handle setting up a fxo for an outgoing call from the repeater? And I was thinking of using FWD Free World Dialup as a source for incoming and outgoing (Using iax of course!) _______________________________________________ App_rpt mailing list App_rpt at lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt -------------- next part -------------- A non-text attachment was scrubbed... Name: app_rpt.c_original Type: application/octet-stream Size: 290704 bytes Desc: not available URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: app_rpt.c_modified by me Type: application/octet-stream Size: 290724 bytes Desc: not available URL: From renato.ornelas at gmail.com Tue Jul 24 12:24:28 2007 From: renato.ornelas at gmail.com (Renato Ornelas) Date: Tue, 24 Jul 2007 09:24:28 -0300 Subject: [App_rpt] Can't monitor on node In-Reply-To: <4693DFB4.1020101@rodgers.sdcoxmail.com> References: <4693DFB4.1020101@rodgers.sdcoxmail.com> Message-ID: Hi.. I was a bit busy last few days, so I couldn't make the tests you told me to do... Using the radio configuration software, i can receive in one pin the signal i can hook to COR (in one pin it swings from 0V to 3.3V in the other it goes from 0V to 13V) 1) Can I use the 3.3V pin and the corthresh=3125 option on zaptel.conf 2) If not, can I use 13V without the risk to fry the quad radio? But what I think strange is that even if i put 5V (from the PSU) directly on the COR pin, the light doesn't light either. Does this have something with zaptel.conf, asterisk or what? Even with asterisk not loaded does it have to light? my zaptel.conf e&m=1-4 # This needs to match the number of channels used in rpt.conf and zapata.conf loadzone = us defaultzone=us invertcor=y channels=1-4 exttone=n 2007/7/10, Stephen Rodgers : > > > The problem you are experiencing has nothing to do with link status, or > whether the repeater is linked or not. It is most likely a hardware > interface or zaptel configuration issue. > > To hear receive audio, you must make sure you have COR hooked up to the > quad radio card. The way to test this is to use another radio to > simulate a transmission to the radio connected to the Quad PCI radio > card, The green light on the back of tha card should light when a signal > is received and go out when the signal goes away. If this is not > happening, then this is why you aren't hearing any receive audio. > > If you are not getting a green light on the card when a signal is > received, try the following: > > 1. With a voltmeter or scope Make sure the COR swings from 0V to greater > than 5V or 5V to 0V when a signal is received. > > > 2. Make sure that the ctcss statement(s) are commented out in > zaptel.conf like this: > > #ctcss=1109,2,1109 > > and that exttone is set to n: > > exttone=n > > and that invertcor=y or invertcor=n is set so that the green light comes > on when a signal is received and goes out when the signal goes away. > Change it to the opposite of what is if the green light is on with no > signal and off with a signal. > > > Steve. > > > > Renato Ornelas wrote: > > Hello dear friends! > > > > I'm using a PCI Quad Radio card with a Motorola EM400 radio pluged in. I > > can > > use a SIP phone to connect to the node (1999) and issue the PTT command > > (*98) and deactivate it (#). I want to be able to listen to this channel > > when I dial to the node but when I ask for the Link status (*7), all I > > receive on the phone and on the remote radio is "node 1999 repeat_only". > I > > tried the duplex=2 option but it didnt work either. > > > > Thanks in avance. > > > > My rpt.conf: > > > > ; > > ; Your repeater > > ; > > > > [1999] ; Name of First Repeater > > > > rxchannel = Zap/1 ; Rx audio/signalling channel > > ; Note: if you use a unified interface (tx/rx on one channel), only > > ; specify the rxchannel and the txchannel will be assumed from the > > rxchannel > > ;rxnotch=1065,40 ; Notch a particular frequency, > > depth > > ; app_rpt must have been compiled > > with > > ; the notch option > > duplex=2 > > functions=functions ; Repeater Function Table > > link_functions=link-functions ; Link Function Table > > phone_functions=functions ; Phone Function table (reverse > > patch) > > telemetry=telemetry ; Telemetry descriptions > > wait_times=wait-times ; Wait times > > context = radio ; dialing context for phone > > callerid = "Your Repeater" <6198192562> ; callerid for phone calls > > idrecording = /etc/asterisk/id ; id recording > > accountcode=RADIO ; account code (optional) > > hangtime=100 ; squelch tail hang time (in ms) > > (optional) > > totime=180000 ; transmit time-out time (in ms) > > (optional) > > idtime=300000 ; id interval time (in ms) > > (optional) > > > > ; The default values for hangtime, time-out time, and id interval time > are > > ; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms) > > ; respectively > > > > politeid=30000 ; time in milliseconds before ID > > timer > > ; expires to try and ID in the > tail. > > ; (optional, default is 30000). > > idtalkover=|iid/r ; Talkover ID (optional) default > is > > none > > unlinkedct=ct2 ; unlinked courtesy tone > (optional) > > default is none > > > > [functions] > > 1=ilink,1 ; Specific link disconnect > > 2=ilink,2 ; Specific Link connect > - monitor > > only > > 3=ilink,3 ; Specific Link connect - > > transceive > > 4=ilink,4 ; Enter command mode on a > specific > > link > > 5=macro,1 ; Command macros (Defined in the > > macro section) > > 7=ilink,5 ; Link status > > 984=ilink,7 ; Last node to key us up > > > > 80=status,1 ; System info > > 81=status,2 ; Time > > 82=status,3 ; app_rpt.c Version > > 87=ilink,15 ; Global node query (all nodes > in > > network) > > > > 6=autopatchup > > 0=autopatchdn ; Autopatch down > > > > ; Control operator commands > > > > 919296=cop,1 ; System warm boot > > 919297=cop,2 ; System enable > > 919298=cop,3 ; System disable > > 99=cop,4 ; Audio test tone > > 98=cop,6 ; Telephone key PTT > > > > > > > > [link-functions] > > 1=ilink,1 ; Specific link disconnect > > 2=ilink,2 ; Specific Link connect > - monitor > > only > > 3=ilink,3 ; Specific Link connect - > > transceive > > 5=macro,1 ; Command macros (Defined in the > > macro section) > > 7=ilink,5 ; Link status > > > > 80=status,1 ; System info > > 81=status,2 ; Time > > 82=status,3 ; app_rpt.c Version > > 87=ilink,15 ; Global node query (all nodes > in > > network) > > > > 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up > > 0=autopatchdn ; Autopatch down > > > > [nodes] > > 1999 = radio at 127.0.0.1/1999,NONE ; This must be changed to your > node > > number > > > > > > ------------------------------------------------------------------------ > > > > _______________________________________________ > > App_rpt mailing list > > App_rpt at lists.illiana.net > > http://lists.illiana.net/mailman/listinfo/app_rpt > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt > -------------- next part -------------- An HTML attachment was scrubbed... URL: From hwstar at rodgers.sdcoxmail.com Tue Jul 24 15:16:39 2007 From: hwstar at rodgers.sdcoxmail.com (Stephen Rodgers) Date: Tue, 24 Jul 2007 08:16:39 -0700 Subject: [App_rpt] Can't monitor on node In-Reply-To: References: <4693DFB4.1020101@rodgers.sdcoxmail.com> Message-ID: <46A617D7.2090200@rodgers.sdcoxmail.com> Renato, See my answers below. Renato Ornelas wrote: > Hi.. I was a bit busy last few days, so I couldn't make the tests you told > me to do... > > Using the radio configuration software, i can receive in one pin the signal > i can hook to COR (in one pin it swings from 0V to 3.3V in the other it > goes > from 0V to 13V) > 1) Can I use the 3.3V pin and the corthresh=3125 option on zaptel.conf Use the 13V signal > 2) If not, can I use 13V without the risk to fry the quad radio? Yes, the COR input has a 1 meg resistor and a zener diode on the input. It will take 13V with no problem. Do not apply 12V to the UIOA or UIOB pins as they have tiny 220 ohm resistors in series with the inputs and you could damage the resistors. > > But what I think strange is that even if i put 5V (from the PSU) > directly on > the COR pin, the light doesn't light either. Does this have something with > zaptel.conf, asterisk or what? Even with asterisk not loaded does it > have to > light? Your config file looks good. If you are using the pciradio driver which came in the asterisk tarball, then that is the reason why you don't see a green light when the COR is asserted. Please download a later version pciradio.c from https://sv.qrvc.com.viewvc.pciradio. Also to get all of latest features in app_rpt.c download a new version from https://sv.qrvc.com/viewvc/app_rpt > > my zaptel.conf > > e&m=1-4 # This needs to match the number of channels used in rpt.conf and > zapata.conf > loadzone = us > defaultzone=us > > invertcor=y > channels=1-4 > exttone=n > > > > 2007/7/10, Stephen Rodgers : >> >> >> The problem you are experiencing has nothing to do with link status, or >> whether the repeater is linked or not. It is most likely a hardware >> interface or zaptel configuration issue. >> >> To hear receive audio, you must make sure you have COR hooked up to the >> quad radio card. The way to test this is to use another radio to >> simulate a transmission to the radio connected to the Quad PCI radio >> card, The green light on the back of tha card should light when a signal >> is received and go out when the signal goes away. If this is not >> happening, then this is why you aren't hearing any receive audio. >> >> If you are not getting a green light on the card when a signal is >> received, try the following: >> >> 1. With a voltmeter or scope Make sure the COR swings from 0V to greater >> than 5V or 5V to 0V when a signal is received. >> >> >> 2. Make sure that the ctcss statement(s) are commented out in >> zaptel.conf like this: >> >> #ctcss=1109,2,1109 >> >> and that exttone is set to n: >> >> exttone=n >> >> and that invertcor=y or invertcor=n is set so that the green light comes >> on when a signal is received and goes out when the signal goes away. >> Change it to the opposite of what is if the green light is on with no >> signal and off with a signal. >> >> >> Steve. >> >> >> >> Renato Ornelas wrote: >> > Hello dear friends! >> > >> > I'm using a PCI Quad Radio card with a Motorola EM400 radio pluged >> in. I >> > can >> > use a SIP phone to connect to the node (1999) and issue the PTT command >> > (*98) and deactivate it (#). I want to be able to listen to this >> channel >> > when I dial to the node but when I ask for the Link status (*7), all I >> > receive on the phone and on the remote radio is "node 1999 >> repeat_only". >> I >> > tried the duplex=2 option but it didnt work either. >> > >> > Thanks in avance. >> > >> > My rpt.conf: >> > >> > ; >> > ; Your repeater >> > ; >> > >> > [1999] ; Name of First Repeater >> > >> > rxchannel = Zap/1 ; Rx audio/signalling channel >> > ; Note: if you use a unified interface (tx/rx on one channel), only >> > ; specify the rxchannel and the txchannel will be assumed from the >> > rxchannel >> > ;rxnotch=1065,40 ; Notch a particular frequency, >> > depth >> > ; app_rpt must have been >> compiled >> > with >> > ; the notch option >> > duplex=2 >> > functions=functions ; Repeater Function Table >> > link_functions=link-functions ; Link Function Table >> > phone_functions=functions ; Phone Function table (reverse >> > patch) >> > telemetry=telemetry ; Telemetry descriptions >> > wait_times=wait-times ; Wait times >> > context = radio ; dialing context for phone >> > callerid = "Your Repeater" <6198192562> ; callerid for phone calls >> > idrecording = /etc/asterisk/id ; id recording >> > accountcode=RADIO ; account code (optional) >> > hangtime=100 ; squelch tail hang time (in >> ms) >> > (optional) >> > totime=180000 ; transmit time-out time (in >> ms) >> > (optional) >> > idtime=300000 ; id interval time (in ms) >> > (optional) >> > >> > ; The default values for hangtime, time-out time, and id interval time >> are >> > ; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 >> ms) >> > ; respectively >> > >> > politeid=30000 ; time in milliseconds >> before ID >> > timer >> > ; expires to try and ID in the >> tail. >> > ; (optional, default is 30000). >> > idtalkover=|iid/r ; Talkover ID (optional) >> default >> is >> > none >> > unlinkedct=ct2 ; unlinked courtesy tone >> (optional) >> > default is none >> > >> > [functions] >> > 1=ilink,1 ; Specific link disconnect >> > 2=ilink,2 ; Specific Link connect >> - monitor >> > only >> > 3=ilink,3 ; Specific Link connect - >> > transceive >> > 4=ilink,4 ; Enter command mode on a >> specific >> > link >> > 5=macro,1 ; Command macros (Defined in >> the >> > macro section) >> > 7=ilink,5 ; Link status >> > 984=ilink,7 ; Last node to key us up >> > >> > 80=status,1 ; System info >> > 81=status,2 ; Time >> > 82=status,3 ; app_rpt.c Version >> > 87=ilink,15 ; Global node query (all nodes >> in >> > network) >> > >> > 6=autopatchup >> > 0=autopatchdn ; Autopatch down >> > >> > ; Control operator commands >> > >> > 919296=cop,1 ; System warm boot >> > 919297=cop,2 ; System enable >> > 919298=cop,3 ; System disable >> > 99=cop,4 ; Audio test tone >> > 98=cop,6 ; Telephone key PTT >> > >> > >> > >> > [link-functions] >> > 1=ilink,1 ; Specific link disconnect >> > 2=ilink,2 ; Specific Link connect >> - monitor >> > only >> > 3=ilink,3 ; Specific Link connect - >> > transceive >> > 5=macro,1 ; Command macros (Defined in >> the >> > macro section) >> > 7=ilink,5 ; Link status >> > >> > 80=status,1 ; System info >> > 81=status,2 ; Time >> > 82=status,3 ; app_rpt.c Version >> > 87=ilink,15 ; Global node query (all nodes >> in >> > network) >> > >> > 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up >> > 0=autopatchdn ; Autopatch down >> > >> > [nodes] >> > 1999 = radio at 127.0.0.1/1999,NONE ; This must be changed to your >> node >> > number >> > >> > >> > >> ------------------------------------------------------------------------ >> > >> > _______________________________________________ >> > App_rpt mailing list >> > App_rpt at lists.illiana.net >> > http://lists.illiana.net/mailman/listinfo/app_rpt >> >> _______________________________________________ >> App_rpt mailing list >> App_rpt at lists.illiana.net >> http://lists.illiana.net/mailman/listinfo/app_rpt >> > > > ------------------------------------------------------------------------ > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt From renato.ornelas at gmail.com Tue Jul 24 17:46:55 2007 From: renato.ornelas at gmail.com (Renato Ornelas) Date: Tue, 24 Jul 2007 14:46:55 -0300 Subject: [App_rpt] Can't monitor on node In-Reply-To: <46A617D7.2090200@rodgers.sdcoxmail.com> References: <4693DFB4.1020101@rodgers.sdcoxmail.com> <46A617D7.2090200@rodgers.sdcoxmail.com> Message-ID: Thank you very much... now I can monitor what's going on the radio channel with my sip phone. I guess this pciradio.c should go into the howto... I tought the version that comes with zaptel was alright... Another question... How does the DTMF stuff work with both zaptel.cfg and app_rpt? 2007/7/24, Stephen Rodgers : > > Renato, > > See my answers below. > > Renato Ornelas wrote: > > Hi.. I was a bit busy last few days, so I couldn't make the tests you > told > > me to do... > > > > Using the radio configuration software, i can receive in one pin the > signal > > i can hook to COR (in one pin it swings from 0V to 3.3V in the other it > > goes > > from 0V to 13V) > > 1) Can I use the 3.3V pin and the corthresh=3125 option on zaptel.conf > > Use the 13V signal > > > 2) If not, can I use 13V without the risk to fry the quad radio? > > Yes, the COR input has a 1 meg resistor and a zener diode on the input. > It will take 13V with no problem. > > Do not apply 12V to the UIOA or UIOB pins as they have tiny 220 ohm > resistors in series with the inputs and you could damage the resistors. > > > > > But what I think strange is that even if i put 5V (from the PSU) > > directly on > > the COR pin, the light doesn't light either. Does this have something > with > > zaptel.conf, asterisk or what? Even with asterisk not loaded does it > > have to > > light? > > Your config file looks good. > > > If you are using the pciradio driver which came in the asterisk tarball, > then that is the reason why you don't see a green light when the COR is > asserted. Please download a later version pciradio.c from > https://sv.qrvc.com.viewvc.pciradio. > > Also to get all of latest features in app_rpt.c download a new version > from https://sv.qrvc.com/viewvc/app_rpt > > > > > > > my zaptel.conf > > > > e&m=1-4 # This needs to match the number of channels used in rpt.confand > > zapata.conf > > loadzone = us > > defaultzone=us > > > > invertcor=y > > channels=1-4 > > exttone=n > > > > > > > > 2007/7/10, Stephen Rodgers : > >> > >> > >> The problem you are experiencing has nothing to do with link status, or > >> whether the repeater is linked or not. It is most likely a hardware > >> interface or zaptel configuration issue. > >> > >> To hear receive audio, you must make sure you have COR hooked up to the > >> quad radio card. The way to test this is to use another radio to > >> simulate a transmission to the radio connected to the Quad PCI radio > >> card, The green light on the back of tha card should light when a > signal > >> is received and go out when the signal goes away. If this is not > >> happening, then this is why you aren't hearing any receive audio. > >> > >> If you are not getting a green light on the card when a signal is > >> received, try the following: > >> > >> 1. With a voltmeter or scope Make sure the COR swings from 0V to > greater > >> than 5V or 5V to 0V when a signal is received. > >> > >> > >> 2. Make sure that the ctcss statement(s) are commented out in > >> zaptel.conf like this: > >> > >> #ctcss=1109,2,1109 > >> > >> and that exttone is set to n: > >> > >> exttone=n > >> > >> and that invertcor=y or invertcor=n is set so that the green light > comes > >> on when a signal is received and goes out when the signal goes away. > >> Change it to the opposite of what is if the green light is on with no > >> signal and off with a signal. > >> > >> > >> Steve. > >> > >> > >> > >> Renato Ornelas wrote: > >> > Hello dear friends! > >> > > >> > I'm using a PCI Quad Radio card with a Motorola EM400 radio pluged > >> in. I > >> > can > >> > use a SIP phone to connect to the node (1999) and issue the PTT > command > >> > (*98) and deactivate it (#). I want to be able to listen to this > >> channel > >> > when I dial to the node but when I ask for the Link status (*7), all > I > >> > receive on the phone and on the remote radio is "node 1999 > >> repeat_only". > >> I > >> > tried the duplex=2 option but it didnt work either. > >> > > >> > Thanks in avance. > >> > > >> > My rpt.conf: > >> > > >> > ; > >> > ; Your repeater > >> > ; > >> > > >> > [1999] ; Name of First Repeater > >> > > >> > rxchannel = Zap/1 ; Rx audio/signalling channel > >> > ; Note: if you use a unified interface (tx/rx on one channel), only > >> > ; specify the rxchannel and the txchannel will be assumed from the > >> > rxchannel > >> > ;rxnotch=1065,40 ; Notch a particular > frequency, > >> > depth > >> > ; app_rpt must have been > >> compiled > >> > with > >> > ; the notch option > >> > duplex=2 > >> > functions=functions ; Repeater Function Table > >> > link_functions=link-functions ; Link Function Table > >> > phone_functions=functions ; Phone Function table > (reverse > >> > patch) > >> > telemetry=telemetry ; Telemetry descriptions > >> > wait_times=wait-times ; Wait times > >> > context = radio ; dialing context for phone > >> > callerid = "Your Repeater" <6198192562> ; callerid for phone calls > >> > idrecording = /etc/asterisk/id ; id recording > >> > accountcode=RADIO ; account code (optional) > >> > hangtime=100 ; squelch tail hang time (in > >> ms) > >> > (optional) > >> > totime=180000 ; transmit time-out time (in > >> ms) > >> > (optional) > >> > idtime=300000 ; id interval time (in ms) > >> > (optional) > >> > > >> > ; The default values for hangtime, time-out time, and id interval > time > >> are > >> > ; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 > >> ms) > >> > ; respectively > >> > > >> > politeid=30000 ; time in milliseconds > >> before ID > >> > timer > >> > ; expires to try and ID in the > >> tail. > >> > ; (optional, default is > 30000). > >> > idtalkover=|iid/r ; Talkover ID (optional) > >> default > >> is > >> > none > >> > unlinkedct=ct2 ; unlinked courtesy tone > >> (optional) > >> > default is none > >> > > >> > [functions] > >> > 1=ilink,1 ; Specific link disconnect > >> > 2=ilink,2 ; Specific Link connect > >> - monitor > >> > only > >> > 3=ilink,3 ; Specific Link connect - > >> > transceive > >> > 4=ilink,4 ; Enter command mode on a > >> specific > >> > link > >> > 5=macro,1 ; Command macros (Defined in > >> the > >> > macro section) > >> > 7=ilink,5 ; Link status > >> > 984=ilink,7 ; Last node to key us up > >> > > >> > 80=status,1 ; System info > >> > 81=status,2 ; Time > >> > 82=status,3 ; app_rpt.c Version > >> > 87=ilink,15 ; Global node query (all > nodes > >> in > >> > network) > >> > > >> > 6=autopatchup > >> > 0=autopatchdn ; Autopatch down > >> > > >> > ; Control operator commands > >> > > >> > 919296=cop,1 ; System warm boot > >> > 919297=cop,2 ; System enable > >> > 919298=cop,3 ; System disable > >> > 99=cop,4 ; Audio test tone > >> > 98=cop,6 ; Telephone key PTT > >> > > >> > > >> > > >> > [link-functions] > >> > 1=ilink,1 ; Specific link disconnect > >> > 2=ilink,2 ; Specific Link connect > >> - monitor > >> > only > >> > 3=ilink,3 ; Specific Link connect - > >> > transceive > >> > 5=macro,1 ; Command macros (Defined in > >> the > >> > macro section) > >> > 7=ilink,5 ; Link status > >> > > >> > 80=status,1 ; System info > >> > 81=status,2 ; Time > >> > 82=status,3 ; app_rpt.c Version > >> > 87=ilink,15 ; Global node query (all > nodes > >> in > >> > network) > >> > > >> > 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch > up > >> > 0=autopatchdn ; Autopatch down > >> > > >> > [nodes] > >> > 1999 = radio at 127.0.0.1/1999,NONE ; This must be changed to > your > >> node > >> > number > >> > > >> > > >> > > >> > ------------------------------------------------------------------------ > >> > > >> > _______________________________________________ > >> > App_rpt mailing list > >> > App_rpt at lists.illiana.net > >> > http://lists.illiana.net/mailman/listinfo/app_rpt > >> > >> _______________________________________________ > >> App_rpt mailing list > >> App_rpt at lists.illiana.net > >> http://lists.illiana.net/mailman/listinfo/app_rpt > >> > > > > > > ------------------------------------------------------------------------ > > > > _______________________________________________ > > App_rpt mailing list > > App_rpt at lists.illiana.net > > http://lists.illiana.net/mailman/listinfo/app_rpt > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt > -------------- next part -------------- An HTML attachment was scrubbed... URL: From renato.ornelas at gmail.com Tue Jul 24 19:32:55 2007 From: renato.ornelas at gmail.com (Renato Ornelas) Date: Tue, 24 Jul 2007 16:32:55 -0300 Subject: [App_rpt] Can't monitor on node In-Reply-To: References: <4693DFB4.1020101@rodgers.sdcoxmail.com> <46A617D7.2090200@rodgers.sdcoxmail.com> Message-ID: Actually what I need is: The remote radio send its ID when I press the PTT... I want to receive this ID and pass it to another repeater. I believe the ID comes as a DTMF. Can the quadradio receive (and decode this remote radio ID)? Thanks again.. Renato Ornelas -------------- next part -------------- An HTML attachment was scrubbed... URL: From hwstar at rodgers.sdcoxmail.com Tue Jul 24 19:34:54 2007 From: hwstar at rodgers.sdcoxmail.com (Stephen Rodgers) Date: Tue, 24 Jul 2007 12:34:54 -0700 Subject: [App_rpt] Can't monitor on node In-Reply-To: References: <4693DFB4.1020101@rodgers.sdcoxmail.com> <46A617D7.2090200@rodgers.sdcoxmail.com> Message-ID: <46A6545E.7060003@rodgers.sdcoxmail.com> Renato, See below Renato Ornelas wrote: > Thank you very much... now I can monitor what's going on the radio channel > with my sip phone. > > I guess this pciradio.c should go into the howto... I tought the version > that comes with zaptel was alright... > > Another question... How does the DTMF stuff work with both zaptel.cfg and Zaptel.conf has nothing to do with DTMF. DTMF commands are configured in rpt.conf. You must have set all of the audio levels correctly for DTMF to decode reliably. There's a document on app-rpt.qrvc.com which shows the procedure. If you update app_rpt.c to the latest version, you may simulate DTMF commands on the asterisk command line using the rpt fun command. > app_rpt? > > > 2007/7/24, Stephen Rodgers : >> >> Renato, >> >> See my answers below. >> >> Renato Ornelas wrote: >> > Hi.. I was a bit busy last few days, so I couldn't make the tests you >> told >> > me to do... >> > >> > Using the radio configuration software, i can receive in one pin the >> signal >> > i can hook to COR (in one pin it swings from 0V to 3.3V in the other it >> > goes >> > from 0V to 13V) >> > 1) Can I use the 3.3V pin and the corthresh=3125 option on zaptel.conf >> >> Use the 13V signal >> >> > 2) If not, can I use 13V without the risk to fry the quad radio? >> >> Yes, the COR input has a 1 meg resistor and a zener diode on the input. >> It will take 13V with no problem. >> >> Do not apply 12V to the UIOA or UIOB pins as they have tiny 220 ohm >> resistors in series with the inputs and you could damage the resistors. >> >> > >> > But what I think strange is that even if i put 5V (from the PSU) >> > directly on >> > the COR pin, the light doesn't light either. Does this have something >> with >> > zaptel.conf, asterisk or what? Even with asterisk not loaded does it >> > have to >> > light? >> >> Your config file looks good. >> >> >> If you are using the pciradio driver which came in the asterisk tarball, >> then that is the reason why you don't see a green light when the COR is >> asserted. Please download a later version pciradio.c from >> https://sv.qrvc.com.viewvc.pciradio. >> >> Also to get all of latest features in app_rpt.c download a new version >> from https://sv.qrvc.com/viewvc/app_rpt >> >> >> >> > >> > my zaptel.conf >> > >> > e&m=1-4 # This needs to match the number of channels used in >> rpt.confand >> > zapata.conf >> > loadzone = us >> > defaultzone=us >> > >> > invertcor=y >> > channels=1-4 >> > exttone=n >> > >> > >> > >> > 2007/7/10, Stephen Rodgers : >> >> >> >> >> >> The problem you are experiencing has nothing to do with link >> status, or >> >> whether the repeater is linked or not. It is most likely a hardware >> >> interface or zaptel configuration issue. >> >> >> >> To hear receive audio, you must make sure you have COR hooked up to >> the >> >> quad radio card. The way to test this is to use another radio to >> >> simulate a transmission to the radio connected to the Quad PCI radio >> >> card, The green light on the back of tha card should light when a >> signal >> >> is received and go out when the signal goes away. If this is not >> >> happening, then this is why you aren't hearing any receive audio. >> >> >> >> If you are not getting a green light on the card when a signal is >> >> received, try the following: >> >> >> >> 1. With a voltmeter or scope Make sure the COR swings from 0V to >> greater >> >> than 5V or 5V to 0V when a signal is received. >> >> >> >> >> >> 2. Make sure that the ctcss statement(s) are commented out in >> >> zaptel.conf like this: >> >> >> >> #ctcss=1109,2,1109 >> >> >> >> and that exttone is set to n: >> >> >> >> exttone=n >> >> >> >> and that invertcor=y or invertcor=n is set so that the green light >> comes >> >> on when a signal is received and goes out when the signal goes away. >> >> Change it to the opposite of what is if the green light is on with no >> >> signal and off with a signal. >> >> >> >> >> >> Steve. >> >> >> >> >> >> >> >> Renato Ornelas wrote: >> >> > Hello dear friends! >> >> > >> >> > I'm using a PCI Quad Radio card with a Motorola EM400 radio pluged >> >> in. I >> >> > can >> >> > use a SIP phone to connect to the node (1999) and issue the PTT >> command >> >> > (*98) and deactivate it (#). I want to be able to listen to this >> >> channel >> >> > when I dial to the node but when I ask for the Link status (*7), all >> I >> >> > receive on the phone and on the remote radio is "node 1999 >> >> repeat_only". >> >> I >> >> > tried the duplex=2 option but it didnt work either. >> >> > >> >> > Thanks in avance. >> >> > >> >> > My rpt.conf: >> >> > >> >> > ; >> >> > ; Your repeater >> >> > ; >> >> > >> >> > [1999] ; Name of First Repeater >> >> > >> >> > rxchannel = Zap/1 ; Rx audio/signalling >> channel >> >> > ; Note: if you use a unified interface (tx/rx on one channel), only >> >> > ; specify the rxchannel and the txchannel will be assumed from the >> >> > rxchannel >> >> > ;rxnotch=1065,40 ; Notch a particular >> frequency, >> >> > depth >> >> > ; app_rpt must have been >> >> compiled >> >> > with >> >> > ; the notch option >> >> > duplex=2 >> >> > functions=functions ; Repeater Function Table >> >> > link_functions=link-functions ; Link Function Table >> >> > phone_functions=functions ; Phone Function table >> (reverse >> >> > patch) >> >> > telemetry=telemetry ; Telemetry descriptions >> >> > wait_times=wait-times ; Wait times >> >> > context = radio ; dialing context for phone >> >> > callerid = "Your Repeater" <6198192562> ; callerid for phone calls >> >> > idrecording = /etc/asterisk/id ; id recording >> >> > accountcode=RADIO ; account code (optional) >> >> > hangtime=100 ; squelch tail hang time (in >> >> ms) >> >> > (optional) >> >> > totime=180000 ; transmit time-out time (in >> >> ms) >> >> > (optional) >> >> > idtime=300000 ; id interval time (in ms) >> >> > (optional) >> >> > >> >> > ; The default values for hangtime, time-out time, and id interval >> time >> >> are >> >> > ; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 >> >> ms) >> >> > ; respectively >> >> > >> >> > politeid=30000 ; time in milliseconds >> >> before ID >> >> > timer >> >> > ; expires to try and ID in >> the >> >> tail. >> >> > ; (optional, default is >> 30000). >> >> > idtalkover=|iid/r ; Talkover ID (optional) >> >> default >> >> is >> >> > none >> >> > unlinkedct=ct2 ; unlinked courtesy tone >> >> (optional) >> >> > default is none >> >> > >> >> > [functions] >> >> > 1=ilink,1 ; Specific link disconnect >> >> > 2=ilink,2 ; Specific Link connect >> >> - monitor >> >> > only >> >> > 3=ilink,3 ; Specific Link connect - >> >> > transceive >> >> > 4=ilink,4 ; Enter command mode on a >> >> specific >> >> > link >> >> > 5=macro,1 ; Command macros (Defined in >> >> the >> >> > macro section) >> >> > 7=ilink,5 ; Link status >> >> > 984=ilink,7 ; Last node to key us up >> >> > >> >> > 80=status,1 ; System info >> >> > 81=status,2 ; Time >> >> > 82=status,3 ; app_rpt.c Version >> >> > 87=ilink,15 ; Global node query (all >> nodes >> >> in >> >> > network) >> >> > >> >> > 6=autopatchup >> >> > 0=autopatchdn ; Autopatch down >> >> > >> >> > ; Control operator commands >> >> > >> >> > 919296=cop,1 ; System warm boot >> >> > 919297=cop,2 ; System enable >> >> > 919298=cop,3 ; System disable >> >> > 99=cop,4 ; Audio test tone >> >> > 98=cop,6 ; Telephone key PTT >> >> > >> >> > >> >> > >> >> > [link-functions] >> >> > 1=ilink,1 ; Specific link disconnect >> >> > 2=ilink,2 ; Specific Link connect >> >> - monitor >> >> > only >> >> > 3=ilink,3 ; Specific Link connect - >> >> > transceive >> >> > 5=macro,1 ; Command macros (Defined in >> >> the >> >> > macro section) >> >> > 7=ilink,5 ; Link status >> >> > >> >> > 80=status,1 ; System info >> >> > 81=status,2 ; Time >> >> > 82=status,3 ; app_rpt.c Version >> >> > 87=ilink,15 ; Global node query (all >> nodes >> >> in >> >> > network) >> >> > >> >> > 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch >> up >> >> > 0=autopatchdn ; Autopatch down >> >> > >> >> > [nodes] >> >> > 1999 = radio at 127.0.0.1/1999,NONE ; This must be changed to >> your >> >> node >> >> > number >> >> > >> >> > >> >> > >> >> >> ------------------------------------------------------------------------ >> >> > >> >> > _______________________________________________ >> >> > App_rpt mailing list >> >> > App_rpt at lists.illiana.net >> >> > http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >> >> _______________________________________________ >> >> App_rpt mailing list >> >> App_rpt at lists.illiana.net >> >> http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >> > >> > >> > >> ------------------------------------------------------------------------ >> > >> > _______________________________________________ >> > App_rpt mailing list >> > App_rpt at lists.illiana.net >> > http://lists.illiana.net/mailman/listinfo/app_rpt >> >> _______________________________________________ >> App_rpt mailing list >> App_rpt at lists.illiana.net >> http://lists.illiana.net/mailman/listinfo/app_rpt >> > > > ------------------------------------------------------------------------ > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt From hwstar at rodgers.sdcoxmail.com Tue Jul 24 22:02:15 2007 From: hwstar at rodgers.sdcoxmail.com (Stephen Rodgers) Date: Tue, 24 Jul 2007 15:02:15 -0700 Subject: [App_rpt] Can't monitor on node In-Reply-To: References: <4693DFB4.1020101@rodgers.sdcoxmail.com> <46A617D7.2090200@rodgers.sdcoxmail.com> Message-ID: <46A676E7.102@rodgers.sdcoxmail.com> Renato, app_rpt.c would have to be modified to accept the DTMF sequences. There is no support in app_rpt.c to do this. Steve. Renato Ornelas wrote: > Actually what I need is: > > The remote radio send its ID when I press the PTT... I want to receive this > ID and pass it to another repeater. I believe the ID comes as a DTMF. Can > the quadradio receive (and decode this remote radio ID)? > > Thanks again.. > > Renato Ornelas > > > ------------------------------------------------------------------------ > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt From renato.ornelas at gmail.com Wed Jul 25 11:53:07 2007 From: renato.ornelas at gmail.com (Renato Ornelas) Date: Wed, 25 Jul 2007 08:53:07 -0300 Subject: [App_rpt] Can't monitor on node In-Reply-To: <46A676E7.102@rodgers.sdcoxmail.com> References: <4693DFB4.1020101@rodgers.sdcoxmail.com> <46A617D7.2090200@rodgers.sdcoxmail.com> <46A676E7.102@rodgers.sdcoxmail.com> Message-ID: Stephen, The PTT-ID info gets encoded by the radio using MDC-1200 ( http://en.wikipedia.org/wiki/MDC-1200). Does app_rpt have something like this so you can point me the direction to start making the modifications to suit my applications? Sorry to bother you (again), but this is a very huge project and the time is very short. I need this ID stuff to deliver the first prototype the field Thanks in Advance, Renato 2007/7/24, Stephen Rodgers : > > Renato, > > app_rpt.c would have to be modified to accept the DTMF sequences. There > is no support in app_rpt.c to do this. > > Steve. > > > > Renato Ornelas wrote: > > Actually what I need is: > > > > The remote radio send its ID when I press the PTT... I want to receive > this > > ID and pass it to another repeater. I believe the ID comes as a DTMF. > Can > > the quadradio receive (and decode this remote radio ID)? > > > > Thanks again.. > > > > Renato Ornelas > > > > > > ------------------------------------------------------------------------ > > > > _______________________________________________ > > App_rpt mailing list > > App_rpt at lists.illiana.net > > http://lists.illiana.net/mailman/listinfo/app_rpt > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt > -------------- next part -------------- An HTML attachment was scrubbed... URL: From telesistant at hotmail.com Wed Jul 25 14:16:23 2007 From: telesistant at hotmail.com (Jim Duuuude) Date: Wed, 25 Jul 2007 07:16:23 -0700 Subject: [App_rpt] Can't monitor on node In-Reply-To: Message-ID: MDC-1200.. that we can decode easily.. but in what manner do you want it passed to another repeater. and what to do with it there?? >From: "Renato Ornelas" >Reply-To: Asterisk Repeater Controler >To: "Asterisk Repeater Controler" >Subject: Re: [App_rpt] Can't monitor on node >Date: Wed, 25 Jul 2007 08:53:07 -0300 >MIME-Version: 1.0 >Received: from marauder.illiana.net ([64.212.212.35]) by >bay0-mc10-f8.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); Wed, >25 Jul 2007 04:53:24 -0700 >Received: (qmail 6067 invoked by uid 1484); 25 Jul 2007 10:53:21 -0000 >Received: from 127.0.0.1 by marauder (envelope-from >, uid 71) with qmail-scanner-2.01 >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.050474 >secs); 25 Jul 2007 10:53:21 -0000 >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; 25 >Jul 2007 10:53:21 -0000 >Received: (qmail 6000 invoked by uid 1484); 25 Jul 2007 10:53:12 -0000 >Received: from 209.85.134.190 by marauder >(envelope-from, uid 71) with qmail-scanner-2.01 >(clamdscan: 0.84/2481. Clear:RC:0(209.85.134.190):. Processed in 0.045554 >secs); 25 Jul 2007 10:53:12 -0000 >Received: from mu-out-0910.google.com (209.85.134.190)by 0 with SMTP; 25 >Jul 2007 10:53:11 -0000 >Received: by mu-out-0910.google.com with SMTP id w9so168324muefor >; Wed, 25 Jul 2007 04:53:08 -0700 (PDT) >Received: by 10.82.136.4 with SMTP id j4mr364511bud.1185364387131;Wed, 25 >Jul 2007 04:53:07 -0700 (PDT) >Received: by 10.82.111.6 with HTTP; Wed, 25 Jul 2007 04:53:07 -0700 (PDT) >X-Message-Info: >txF49lGdW40wFwR9dlynL+Bs/CSQlSh7q6wN9n27ktXY//w4DLvEz/vHba9TlyjO >Return-Path: >Delivered-To: mailman-app_rpt at lists.illiana.net >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=ShAt5adC/lNgPlRjTRau0KzAD3HJ+LIbCJ8385Td2EMyoMRW/Ppb12k5fi9Gu+sYwUObjF8Tr+ZUnOadqucv1BID5CFuAcWpk5YbqenE9R1Urx26uW3zIUedPOaStLcjSd/B7yZ06QCH+cA3PwwfUS+ACBtTpHq0OlCLkwz2aBY= >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; >s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=sNijDh5T2PkdrjizCqTBZWVkryyTvIQ1uMc5xRViqercGaLaeGs9KJJIEVjO8FZhrTbHVTOU5/7zOzcnyqLWmW9FO37rkn0e7u3K+3VXOWtPUIF4FfT78vmQvnlulpJkz2TgtU/xQMr/SYkF+dPl+p8Y0y7vCo6qy6rkEH9Rom0= >References: ><4693DFB4.1020101 at rodgers.sdcoxmail.com><46A617D7.2090200 at rodgers.sdcoxmail.com><46A676E7.102 at rodgers.sdcoxmail.com> >X-BeenThere: app_rpt at lists.illiana.net >X-Mailman-Version: 2.1.6 >Precedence: list >List-Id: Asterisk Repeater Controler >List-Unsubscribe: >, >List-Archive: >List-Post: >List-Help: >List-Subscribe: >, >Errors-To: app_rpt-bounces at lists.illiana.net >X-OriginalArrivalTime: 25 Jul 2007 11:53:24.0769 (UTC) >FILETIME=[68002910:01C7CEB2] > >Stephen, > >The PTT-ID info gets encoded by the radio using MDC-1200 ( >http://en.wikipedia.org/wiki/MDC-1200). Does app_rpt have something like >this so you can point me the direction to start making the modifications to >suit my applications? > >Sorry to bother you (again), but this is a very huge project and the time >is >very short. I need this ID stuff to deliver the first prototype the field > >Thanks in Advance, >Renato > > >2007/7/24, Stephen Rodgers : >> >>Renato, >> >>app_rpt.c would have to be modified to accept the DTMF sequences. There >>is no support in app_rpt.c to do this. >> >>Steve. >> >> >> >>Renato Ornelas wrote: >> > Actually what I need is: >> > >> > The remote radio send its ID when I press the PTT... I want to receive >>this >> > ID and pass it to another repeater. I believe the ID comes as a DTMF. >>Can >> > the quadradio receive (and decode this remote radio ID)? >> > >> > Thanks again.. >> > >> > Renato Ornelas >> > >> > >> > >>------------------------------------------------------------------------ >> > >> > _______________________________________________ >> > App_rpt mailing list >> > App_rpt at lists.illiana.net >> > http://lists.illiana.net/mailman/listinfo/app_rpt >> >>_______________________________________________ >>App_rpt mailing list >>App_rpt at lists.illiana.net >>http://lists.illiana.net/mailman/listinfo/app_rpt >> >_______________________________________________ >App_rpt mailing list >App_rpt at lists.illiana.net >http://lists.illiana.net/mailman/listinfo/app_rpt From renato.ornelas at gmail.com Wed Jul 25 19:43:19 2007 From: renato.ornelas at gmail.com (Renato Ornelas) Date: Wed, 25 Jul 2007 16:43:19 -0300 Subject: [App_rpt] Can't monitor on node In-Reply-To: References: Message-ID: Wow.. your solution is so incredible that I'm amazed... I'd like to hear from you what the possibilities are. Maybe there is a better way to make my network.... I'm my scenario the guy with the portable radio press the PTT and this info gets to a management console so that the operator knows that ID 1234 in node 1999 has just pushed the PTT. Something like this... RANDOM GUY -> RADIO->QUADPCI ---------------------- REMOTE ASTERISK -> management console Any way, if i can get this ID associated with the respective channel in the quadradio, I can relay it to the console... The console does not exist yet. Other thing I could you is ID spoof, so the quadradio passes the ID it receives via IAX or SIP. Thanks again. Renato 2007/7/25, Jim Duuuude : > > MDC-1200.. that we can decode easily.. but in what manner do you want it > passed to another > repeater. and what to do with it there?? > > > >From: "Renato Ornelas" > >Reply-To: Asterisk Repeater Controler > >To: "Asterisk Repeater Controler" > >Subject: Re: [App_rpt] Can't monitor on node > >Date: Wed, 25 Jul 2007 08:53:07 -0300 > >MIME-Version: 1.0 > >Received: from marauder.illiana.net ([64.212.212.35]) by > >bay0-mc10-f8.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); Wed, > >25 Jul 2007 04:53:24 -0700 > >Received: (qmail 6067 invoked by uid 1484); 25 Jul 2007 10:53:21 -0000 > >Received: from 127.0.0.1 by marauder (envelope-from > >, uid 71) with qmail-scanner-2.01 > >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.050474 > >secs); 25 Jul 2007 10:53:21 -0000 > >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; > 25 > >Jul 2007 10:53:21 -0000 > >Received: (qmail 6000 invoked by uid 1484); 25 Jul 2007 10:53:12 -0000 > >Received: from 209.85.134.190 by marauder > >(envelope-from, uid 71) with qmail-scanner-2.01 > >(clamdscan: 0.84/2481. Clear:RC:0(209.85.134.190):. Processed in > 0.045554 > >secs); 25 Jul 2007 10:53:12 -0000 > >Received: from mu-out-0910.google.com (209.85.134.190)by 0 with SMTP; 25 > >Jul 2007 10:53:11 -0000 > >Received: by mu-out-0910.google.com with SMTP id w9so168324muefor > >; Wed, 25 Jul 2007 04:53:08 -0700 (PDT) > >Received: by 10.82.136.4 with SMTP id j4mr364511bud.1185364387131;Wed, 25 > >Jul 2007 04:53:07 -0700 (PDT) > >Received: by 10.82.111.6 with HTTP; Wed, 25 Jul 2007 04:53:07 -0700 (PDT) > >X-Message-Info: > >txF49lGdW40wFwR9dlynL+Bs/CSQlSh7q6wN9n27ktXY//w4DLvEz/vHba9TlyjO > >Return-Path: > >Delivered-To: mailman-app_rpt at lists.illiana.net > >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; > > >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=ShAt5adC/lNgPlRjTRau0KzAD3HJ+LIbCJ8385Td2EMyoMRW/Ppb12k5fi9Gu+sYwUObjF8Tr+ZUnOadqucv1BID5CFuAcWpk5YbqenE9R1Urx26uW3zIUedPOaStLcjSd/B7yZ06QCH+cA3PwwfUS+ACBtTpHq0OlCLkwz2aBY= > >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; > > >s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=sNijDh5T2PkdrjizCqTBZWVkryyTvIQ1uMc5xRViqercGaLaeGs9KJJIEVjO8FZhrTbHVTOU5/7zOzcnyqLWmW9FO37rkn0e7u3K+3VXOWtPUIF4FfT78vmQvnlulpJkz2TgtU/xQMr/SYkF+dPl+p8Y0y7vCo6qy6rkEH9Rom0= > >References: > >< > 4693DFB4.1020101 at rodgers.sdcoxmail.com>< > d10818e80707240524q29a438c1h90dcad085e0494fd at mail.gmail.com>< > 46A617D7.2090200 at rodgers.sdcoxmail.com>< > d10818e80707241046m2d739241vfc69d9eed62c9aaa at mail.gmail.com>< > d10818e80707241232r47a3bc47x7e67838a014476ee at mail.gmail.com>< > 46A676E7.102 at rodgers.sdcoxmail.com> > >X-BeenThere: app_rpt at lists.illiana.net > >X-Mailman-Version: 2.1.6 > >Precedence: list > >List-Id: Asterisk Repeater Controler > >List-Unsubscribe: > >, app_rpt-request at lists.illiana.net?subject=unsubscribe> > >List-Archive: > >List-Post: > >List-Help: > >List-Subscribe: > >, app_rpt-request at lists.illiana.net?subject=subscribe> > >Errors-To: app_rpt-bounces at lists.illiana.net > >X-OriginalArrivalTime: 25 Jul 2007 11:53:24.0769 (UTC) > >FILETIME=[68002910:01C7CEB2] > > > >Stephen, > > > >The PTT-ID info gets encoded by the radio using MDC-1200 ( > >http://en.wikipedia.org/wiki/MDC-1200). Does app_rpt have something like > >this so you can point me the direction to start making the modifications > to > >suit my applications? > > > >Sorry to bother you (again), but this is a very huge project and the time > >is > >very short. I need this ID stuff to deliver the first prototype the field > > > >Thanks in Advance, > >Renato > > > > > >2007/7/24, Stephen Rodgers : > >> > >>Renato, > >> > >>app_rpt.c would have to be modified to accept the DTMF sequences. There > >>is no support in app_rpt.c to do this. > >> > >>Steve. > >> > >> > >> > >>Renato Ornelas wrote: > >> > Actually what I need is: > >> > > >> > The remote radio send its ID when I press the PTT... I want to > receive > >>this > >> > ID and pass it to another repeater. I believe the ID comes as a DTMF. > >>Can > >> > the quadradio receive (and decode this remote radio ID)? > >> > > >> > Thanks again.. > >> > > >> > Renato Ornelas > >> > > >> > > >> > > >>------------------------------------------------------------------------ > >> > > >> > _______________________________________________ > >> > App_rpt mailing list > >> > App_rpt at lists.illiana.net > >> > http://lists.illiana.net/mailman/listinfo/app_rpt > >> > >>_______________________________________________ > >>App_rpt mailing list > >>App_rpt at lists.illiana.net > >>http://lists.illiana.net/mailman/listinfo/app_rpt > >> > > > >_______________________________________________ > >App_rpt mailing list > >App_rpt at lists.illiana.net > >http://lists.illiana.net/mailman/listinfo/app_rpt > > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt > -------------- next part -------------- An HTML attachment was scrubbed... URL: From telesistant at hotmail.com Wed Jul 25 20:39:05 2007 From: telesistant at hotmail.com (Jim Duuuude) Date: Wed, 25 Jul 2007 13:39:05 -0700 Subject: [App_rpt] Can't monitor on node In-Reply-To: Message-ID: This should not be too difficult at all, if I understand this. If you could, please email me (at my private address telesistant at hotmail.com, not the list) your phone number, and we can discuss this in real time. >From: "Renato Ornelas" >Reply-To: Asterisk Repeater Controler >To: "Asterisk Repeater Controler" >Subject: Re: [App_rpt] Can't monitor on node >Date: Wed, 25 Jul 2007 16:43:19 -0300 >MIME-Version: 1.0 >Received: from marauder.illiana.net ([64.212.212.35]) by >bay0-mc10-f6.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); Wed, >25 Jul 2007 12:46:13 -0700 >Received: (qmail 30315 invoked by uid 1484); 25 Jul 2007 18:46:10 -0000 >Received: from 127.0.0.1 by marauder (envelope-from >, uid 71) with qmail-scanner-2.01 >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.112553 >secs); 25 Jul 2007 18:46:10 -0000 >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; 25 >Jul 2007 18:46:09 -0000 >Received: (qmail 30246 invoked by uid 1484); 25 Jul 2007 18:45:27 -0000 >Received: from 64.233.182.189 by marauder >(envelope-from, uid 71) with qmail-scanner-2.01 >(clamdscan: 0.84/2481. Clear:RC:0(64.233.182.189):. Processed in 0.225549 >secs); 25 Jul 2007 18:45:27 -0000 >Received: from nf-out-0910.google.com (64.233.182.189)by 0 with SMTP; 25 >Jul 2007 18:45:26 -0000 >Received: by nf-out-0910.google.com with SMTP id g13so18369nfbfor >; Wed, 25 Jul 2007 12:43:20 -0700 (PDT) >Received: by 10.82.174.20 with SMTP id w20mr831865bue.1185392599658;Wed, 25 >Jul 2007 12:43:19 -0700 (PDT) >Received: by 10.82.111.6 with HTTP; Wed, 25 Jul 2007 12:43:19 -0700 (PDT) >X-Message-Info: >txF49lGdW41gOGAMLIbhiGFrGOY9OuthBCWjMKFq2DxUuTGHkmWauyVMy/Ym/xAD >Return-Path: >Delivered-To: mailman-app_rpt at lists.illiana.net >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=NHv0l4ZBzd34R+0jsijNJ+LkvPSEr2LAZLFVW5xlR/FjhL2tN0okAqZ/uJzu0lx5woMQ+74FEIEiYD+HUAOzHf1/H7Tk5KAYmTTdJV7V+UxFeNkm4GbxxdtV9AVk0BKQdZ8e7yXrNhE+zxoai2nyvOew7FeXFG0stDUtIVfDTCk= >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; >s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=K/i4cCsXp7kkZob544NlaphWsSH8T7RDqnRLUXX03VlCFKdPbp6woH7Y0FKfZisaUiTmibl3+wMLYyaryRf9AyFBf3ByksQ+MXaSdNFFhfTRzzsHtXhM9JyJEk8bgH9OHcbUw9sVwovydzsz8FuyTtcJIVUlkP58w/X8KtYpMZU= >References: > >X-BeenThere: app_rpt at lists.illiana.net >X-Mailman-Version: 2.1.6 >Precedence: list >List-Id: Asterisk Repeater Controler >List-Unsubscribe: >, >List-Archive: >List-Post: >List-Help: >List-Subscribe: >, >Errors-To: app_rpt-bounces at lists.illiana.net >X-OriginalArrivalTime: 25 Jul 2007 19:46:13.0594 (UTC) >FILETIME=[752353A0:01C7CEF4] > >Wow.. your solution is so incredible that I'm amazed... I'd like to hear >from you what the possibilities are. Maybe there is a better way to make my >network.... > >I'm my scenario the guy with the portable radio press the PTT and this info >gets to a management console so that the operator knows that ID 1234 in >node >1999 has just pushed the PTT. > >Something like this... > >RANDOM GUY -> RADIO->QUADPCI ---------------------- REMOTE ASTERISK -> >management console > >Any way, if i can get this ID associated with the respective channel in the >quadradio, I can relay it to the console... > >The console does not exist yet. > >Other thing I could you is ID spoof, so the quadradio passes the ID it >receives via IAX or SIP. > >Thanks again. >Renato >2007/7/25, Jim Duuuude : >> >>MDC-1200.. that we can decode easily.. but in what manner do you want it >>passed to another >>repeater. and what to do with it there?? >> >> >> >From: "Renato Ornelas" >> >Reply-To: Asterisk Repeater Controler >> >To: "Asterisk Repeater Controler" >> >Subject: Re: [App_rpt] Can't monitor on node >> >Date: Wed, 25 Jul 2007 08:53:07 -0300 >> >MIME-Version: 1.0 >> >Received: from marauder.illiana.net ([64.212.212.35]) by >> >bay0-mc10-f8.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); >>Wed, >> >25 Jul 2007 04:53:24 -0700 >> >Received: (qmail 6067 invoked by uid 1484); 25 Jul 2007 10:53:21 -0000 >> >Received: from 127.0.0.1 by marauder (envelope-from >> >, uid 71) with qmail-scanner-2.01 >> >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.050474 >> >secs); 25 Jul 2007 10:53:21 -0000 >> >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; >>25 >> >Jul 2007 10:53:21 -0000 >> >Received: (qmail 6000 invoked by uid 1484); 25 Jul 2007 10:53:12 -0000 >> >Received: from 209.85.134.190 by marauder >> >(envelope-from, uid 71) with >>qmail-scanner-2.01 >> >(clamdscan: 0.84/2481. Clear:RC:0(209.85.134.190):. Processed in >>0.045554 >> >secs); 25 Jul 2007 10:53:12 -0000 >> >Received: from mu-out-0910.google.com (209.85.134.190)by 0 with SMTP; 25 >> >Jul 2007 10:53:11 -0000 >> >Received: by mu-out-0910.google.com with SMTP id w9so168324muefor >> >; Wed, 25 Jul 2007 04:53:08 -0700 (PDT) >> >Received: by 10.82.136.4 with SMTP id j4mr364511bud.1185364387131;Wed, >>25 >> >Jul 2007 04:53:07 -0700 (PDT) >> >Received: by 10.82.111.6 with HTTP; Wed, 25 Jul 2007 04:53:07 -0700 >>(PDT) >> >X-Message-Info: >> >txF49lGdW40wFwR9dlynL+Bs/CSQlSh7q6wN9n27ktXY//w4DLvEz/vHba9TlyjO >> >Return-Path: >> >Delivered-To: mailman-app_rpt at lists.illiana.net >> >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; >> >> >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=ShAt5adC/lNgPlRjTRau0KzAD3HJ+LIbCJ8385Td2EMyoMRW/Ppb12k5fi9Gu+sYwUObjF8Tr+ZUnOadqucv1BID5CFuAcWpk5YbqenE9R1Urx26uW3zIUedPOaStLcjSd/B7yZ06QCH+cA3PwwfUS+ACBtTpHq0OlCLkwz2aBY= >> >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; >> >> >s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=sNijDh5T2PkdrjizCqTBZWVkryyTvIQ1uMc5xRViqercGaLaeGs9KJJIEVjO8FZhrTbHVTOU5/7zOzcnyqLWmW9FO37rkn0e7u3K+3VXOWtPUIF4FfT78vmQvnlulpJkz2TgtU/xQMr/SYkF+dPl+p8Y0y7vCo6qy6rkEH9Rom0= >> >References: >> >< >>4693DFB4.1020101 at rodgers.sdcoxmail.com>< >>d10818e80707240524q29a438c1h90dcad085e0494fd at mail.gmail.com>< >>46A617D7.2090200 at rodgers.sdcoxmail.com>< >>d10818e80707241046m2d739241vfc69d9eed62c9aaa at mail.gmail.com>< >>d10818e80707241232r47a3bc47x7e67838a014476ee at mail.gmail.com>< >>46A676E7.102 at rodgers.sdcoxmail.com> >> >X-BeenThere: app_rpt at lists.illiana.net >> >X-Mailman-Version: 2.1.6 >> >Precedence: list >> >List-Id: Asterisk Repeater Controler >> >List-Unsubscribe: >> >,>app_rpt-request at lists.illiana.net?subject=unsubscribe> >> >List-Archive: >> >List-Post: >> >List-Help: >> >List-Subscribe: >> >,>app_rpt-request at lists.illiana.net?subject=subscribe> >> >Errors-To: app_rpt-bounces at lists.illiana.net >> >X-OriginalArrivalTime: 25 Jul 2007 11:53:24.0769 (UTC) >> >FILETIME=[68002910:01C7CEB2] >> > >> >Stephen, >> > >> >The PTT-ID info gets encoded by the radio using MDC-1200 ( >> >http://en.wikipedia.org/wiki/MDC-1200). Does app_rpt have something like >> >this so you can point me the direction to start making the modifications >>to >> >suit my applications? >> > >> >Sorry to bother you (again), but this is a very huge project and the >>time >> >is >> >very short. I need this ID stuff to deliver the first prototype the >>field >> > >> >Thanks in Advance, >> >Renato >> > >> > >> >2007/7/24, Stephen Rodgers : >> >> >> >>Renato, >> >> >> >>app_rpt.c would have to be modified to accept the DTMF sequences. There >> >>is no support in app_rpt.c to do this. >> >> >> >>Steve. >> >> >> >> >> >> >> >>Renato Ornelas wrote: >> >> > Actually what I need is: >> >> > >> >> > The remote radio send its ID when I press the PTT... I want to >>receive >> >>this >> >> > ID and pass it to another repeater. I believe the ID comes as a >>DTMF. >> >>Can >> >> > the quadradio receive (and decode this remote radio ID)? >> >> > >> >> > Thanks again.. >> >> > >> >> > Renato Ornelas >> >> > >> >> > >> >> > >> >>------------------------------------------------------------------------ >> >> > >> >> > _______________________________________________ >> >> > App_rpt mailing list >> >> > App_rpt at lists.illiana.net >> >> > http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >> >>_______________________________________________ >> >>App_rpt mailing list >> >>App_rpt at lists.illiana.net >> >>http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >> >> >> >_______________________________________________ >> >App_rpt mailing list >> >App_rpt at lists.illiana.net >> >http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >>_______________________________________________ >>App_rpt mailing list >>App_rpt at lists.illiana.net >>http://lists.illiana.net/mailman/listinfo/app_rpt >> >_______________________________________________ >App_rpt mailing list >App_rpt at lists.illiana.net >http://lists.illiana.net/mailman/listinfo/app_rpt From renato.ornelas at gmail.com Wed Jul 25 20:46:53 2007 From: renato.ornelas at gmail.com (Renato Ornelas) Date: Wed, 25 Jul 2007 17:46:53 -0300 Subject: [App_rpt] Can't monitor on node In-Reply-To: References: Message-ID: Do you use MSN messenger... because I live in Brazil and my spoken English isn't very good... I'm sure you have trouble to understand everything I write... Thanks 2007/7/25, Jim Duuuude : > > This should not be too difficult at all, if I understand this. If you > could, > please email me > (at my private address telesistant at hotmail.com, not the list) your phone > number, and > we can discuss this in real time. > > > >From: "Renato Ornelas" > >Reply-To: Asterisk Repeater Controler > >To: "Asterisk Repeater Controler" > >Subject: Re: [App_rpt] Can't monitor on node > >Date: Wed, 25 Jul 2007 16:43:19 -0300 > >MIME-Version: 1.0 > >Received: from marauder.illiana.net ([64.212.212.35]) by > >bay0-mc10-f6.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); Wed, > >25 Jul 2007 12:46:13 -0700 > >Received: (qmail 30315 invoked by uid 1484); 25 Jul 2007 18:46:10 -0000 > >Received: from 127.0.0.1 by marauder (envelope-from > >, uid 71) with qmail-scanner-2.01 > >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.112553 > >secs); 25 Jul 2007 18:46:10 -0000 > >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; > 25 > >Jul 2007 18:46:09 -0000 > >Received: (qmail 30246 invoked by uid 1484); 25 Jul 2007 18:45:27 -0000 > >Received: from 64.233.182.189 by marauder > >(envelope-from, uid 71) with qmail-scanner-2.01 > >(clamdscan: 0.84/2481. Clear:RC:0(64.233.182.189):. Processed in > 0.225549 > >secs); 25 Jul 2007 18:45:27 -0000 > >Received: from nf-out-0910.google.com (64.233.182.189)by 0 with SMTP; 25 > >Jul 2007 18:45:26 -0000 > >Received: by nf-out-0910.google.com with SMTP id g13so18369nfbfor > >; Wed, 25 Jul 2007 12:43:20 -0700 (PDT) > >Received: by 10.82.174.20 with SMTP id w20mr831865bue.1185392599658;Wed, > 25 > >Jul 2007 12:43:19 -0700 (PDT) > >Received: by 10.82.111.6 with HTTP; Wed, 25 Jul 2007 12:43:19 -0700 (PDT) > >X-Message-Info: > >txF49lGdW41gOGAMLIbhiGFrGOY9OuthBCWjMKFq2DxUuTGHkmWauyVMy/Ym/xAD > >Return-Path: > >Delivered-To: mailman-app_rpt at lists.illiana.net > >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; > > >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=NHv0l4ZBzd34R+0jsijNJ+LkvPSEr2LAZLFVW5xlR/FjhL2tN0okAqZ/uJzu0lx5woMQ+74FEIEiYD+HUAOzHf1/H7Tk5KAYmTTdJV7V+UxFeNkm4GbxxdtV9AVk0BKQdZ8e7yXrNhE+zxoai2nyvOew7FeXFG0stDUtIVfDTCk= > >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; > > >s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=K/i4cCsXp7kkZob544NlaphWsSH8T7RDqnRLUXX03VlCFKdPbp6woH7Y0FKfZisaUiTmibl3+wMLYyaryRf9AyFBf3ByksQ+MXaSdNFFhfTRzzsHtXhM9JyJEk8bgH9OHcbUw9sVwovydzsz8FuyTtcJIVUlkP58w/X8KtYpMZU= > >References: > >< > BAY119-F303A3F5827241AD48470C5B1F10 at phx.gbl> > >X-BeenThere: app_rpt at lists.illiana.net > >X-Mailman-Version: 2.1.6 > >Precedence: list > >List-Id: Asterisk Repeater Controler > >List-Unsubscribe: > >, app_rpt-request at lists.illiana.net?subject=unsubscribe> > >List-Archive: > >List-Post: > >List-Help: > >List-Subscribe: > >, app_rpt-request at lists.illiana.net?subject=subscribe> > >Errors-To: app_rpt-bounces at lists.illiana.net > >X-OriginalArrivalTime: 25 Jul 2007 19:46:13.0594 (UTC) > >FILETIME=[752353A0:01C7CEF4] > > > >Wow.. your solution is so incredible that I'm amazed... I'd like to hear > >from you what the possibilities are. Maybe there is a better way to make > my > >network.... > > > >I'm my scenario the guy with the portable radio press the PTT and this > info > >gets to a management console so that the operator knows that ID 1234 in > >node > >1999 has just pushed the PTT. > > > >Something like this... > > > >RANDOM GUY -> RADIO->QUADPCI ---------------------- REMOTE ASTERISK -> > >management console > > > >Any way, if i can get this ID associated with the respective channel in > the > >quadradio, I can relay it to the console... > > > >The console does not exist yet. > > > >Other thing I could you is ID spoof, so the quadradio passes the ID it > >receives via IAX or SIP. > > > >Thanks again. > >Renato > >2007/7/25, Jim Duuuude : > >> > >>MDC-1200.. that we can decode easily.. but in what manner do you want it > >>passed to another > >>repeater. and what to do with it there?? > >> > >> > >> >From: "Renato Ornelas" > >> >Reply-To: Asterisk Repeater Controler > >> >To: "Asterisk Repeater Controler" > >> >Subject: Re: [App_rpt] Can't monitor on node > >> >Date: Wed, 25 Jul 2007 08:53:07 -0300 > >> >MIME-Version: 1.0 > >> >Received: from marauder.illiana.net ([64.212.212.35]) by > >> >bay0-mc10-f8.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); > >>Wed, > >> >25 Jul 2007 04:53:24 -0700 > >> >Received: (qmail 6067 invoked by uid 1484); 25 Jul 2007 10:53:21 -0000 > >> >Received: from 127.0.0.1 by marauder (envelope-from > >> >, uid 71) with qmail-scanner-2.01 > >> >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in > 0.050474 > >> >secs); 25 Jul 2007 10:53:21 -0000 > >> >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with > SMTP; > >>25 > >> >Jul 2007 10:53:21 -0000 > >> >Received: (qmail 6000 invoked by uid 1484); 25 Jul 2007 10:53:12 -0000 > >> >Received: from 209.85.134.190 by marauder > >> >(envelope-from, uid 71) with > >>qmail-scanner-2.01 > >> >(clamdscan: 0.84/2481. Clear:RC:0(209.85.134.190):. Processed in > >>0.045554 > >> >secs); 25 Jul 2007 10:53:12 -0000 > >> >Received: from mu-out-0910.google.com (209.85.134.190)by 0 with SMTP; > 25 > >> >Jul 2007 10:53:11 -0000 > >> >Received: by mu-out-0910.google.com with SMTP id w9so168324muefor > >> >; Wed, 25 Jul 2007 04:53:08 -0700 (PDT) > >> >Received: by 10.82.136.4 with SMTP id j4mr364511bud.1185364387131;Wed, > >>25 > >> >Jul 2007 04:53:07 -0700 (PDT) > >> >Received: by 10.82.111.6 with HTTP; Wed, 25 Jul 2007 04:53:07 -0700 > >>(PDT) > >> >X-Message-Info: > >> >txF49lGdW40wFwR9dlynL+Bs/CSQlSh7q6wN9n27ktXY//w4DLvEz/vHba9TlyjO > >> >Return-Path: > >> >Delivered-To: mailman-app_rpt at lists.illiana.net > >> >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; > >> > >> > >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=ShAt5adC/lNgPlRjTRau0KzAD3HJ+LIbCJ8385Td2EMyoMRW/Ppb12k5fi9Gu+sYwUObjF8Tr+ZUnOadqucv1BID5CFuAcWpk5YbqenE9R1Urx26uW3zIUedPOaStLcjSd/B7yZ06QCH+cA3PwwfUS+ACBtTpHq0OlCLkwz2aBY= > >> >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; > >> > >> > >s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=sNijDh5T2PkdrjizCqTBZWVkryyTvIQ1uMc5xRViqercGaLaeGs9KJJIEVjO8FZhrTbHVTOU5/7zOzcnyqLWmW9FO37rkn0e7u3K+3VXOWtPUIF4FfT78vmQvnlulpJkz2TgtU/xQMr/SYkF+dPl+p8Y0y7vCo6qy6rkEH9Rom0= > >> >References: > >> >< > >>4693DFB4.1020101 at rodgers.sdcoxmail.com>< > >>d10818e80707240524q29a438c1h90dcad085e0494fd at mail.gmail.com>< > >>46A617D7.2090200 at rodgers.sdcoxmail.com>< > >>d10818e80707241046m2d739241vfc69d9eed62c9aaa at mail.gmail.com>< > >>d10818e80707241232r47a3bc47x7e67838a014476ee at mail.gmail.com>< > >>46A676E7.102 at rodgers.sdcoxmail.com> > >> >X-BeenThere: app_rpt at lists.illiana.net > >> >X-Mailman-Version: 2.1.6 > >> >Precedence: list > >> >List-Id: Asterisk Repeater Controler > >> >List-Unsubscribe: > >> >, >>app_rpt-request at lists.illiana.net?subject=unsubscribe> > >> >List-Archive: > >> >List-Post: > >> >List-Help: > >> >List-Subscribe: > >> >, >>app_rpt-request at lists.illiana.net?subject=subscribe> > >> >Errors-To: app_rpt-bounces at lists.illiana.net > >> >X-OriginalArrivalTime: 25 Jul 2007 11:53:24.0769 (UTC) > >> >FILETIME=[68002910:01C7CEB2] > >> > > >> >Stephen, > >> > > >> >The PTT-ID info gets encoded by the radio using MDC-1200 ( > >> >http://en.wikipedia.org/wiki/MDC-1200). Does app_rpt have something > like > >> >this so you can point me the direction to start making the > modifications > >>to > >> >suit my applications? > >> > > >> >Sorry to bother you (again), but this is a very huge project and the > >>time > >> >is > >> >very short. I need this ID stuff to deliver the first prototype the > >>field > >> > > >> >Thanks in Advance, > >> >Renato > >> > > >> > > >> >2007/7/24, Stephen Rodgers : > >> >> > >> >>Renato, > >> >> > >> >>app_rpt.c would have to be modified to accept the DTMF sequences. > There > >> >>is no support in app_rpt.c to do this. > >> >> > >> >>Steve. > >> >> > >> >> > >> >> > >> >>Renato Ornelas wrote: > >> >> > Actually what I need is: > >> >> > > >> >> > The remote radio send its ID when I press the PTT... I want to > >>receive > >> >>this > >> >> > ID and pass it to another repeater. I believe the ID comes as a > >>DTMF. > >> >>Can > >> >> > the quadradio receive (and decode this remote radio ID)? > >> >> > > >> >> > Thanks again.. > >> >> > > >> >> > Renato Ornelas > >> >> > > >> >> > > >> >> > > >> > >>------------------------------------------------------------------------ > >> >> > > >> >> > _______________________________________________ > >> >> > App_rpt mailing list > >> >> > App_rpt at lists.illiana.net > >> >> > http://lists.illiana.net/mailman/listinfo/app_rpt > >> >> > >> >>_______________________________________________ > >> >>App_rpt mailing list > >> >>App_rpt at lists.illiana.net > >> >>http://lists.illiana.net/mailman/listinfo/app_rpt > >> >> > >> > >> > >> >_______________________________________________ > >> >App_rpt mailing list > >> >App_rpt at lists.illiana.net > >> >http://lists.illiana.net/mailman/listinfo/app_rpt > >> > >> > >>_______________________________________________ > >>App_rpt mailing list > >>App_rpt at lists.illiana.net > >>http://lists.illiana.net/mailman/listinfo/app_rpt > >> > > > >_______________________________________________ > >App_rpt mailing list > >App_rpt at lists.illiana.net > >http://lists.illiana.net/mailman/listinfo/app_rpt > > > _______________________________________________ > App_rpt mailing list > App_rpt at lists.illiana.net > http://lists.illiana.net/mailman/listinfo/app_rpt > -------------- next part -------------- An HTML attachment was scrubbed... URL: From telesistant at hotmail.com Wed Jul 25 20:56:27 2007 From: telesistant at hotmail.com (Jim Duuuude) Date: Wed, 25 Jul 2007 13:56:27 -0700 Subject: [App_rpt] Can't monitor on node In-Reply-To: Message-ID: no, actually i dont use any of those kind of services. In fact, I hate email. I am definitely a telephone person. Also I am not sure if I even have a way of testing this stuff here because Im not sure if I have a radio that is MDC-1200 equiped here at the moment. I was hoping that I could just call you, and have you use your setup there while I was on the phone with you. >From: "Renato Ornelas" >Reply-To: Asterisk Repeater Controler >To: "Asterisk Repeater Controler" >Subject: Re: [App_rpt] Can't monitor on node >Date: Wed, 25 Jul 2007 17:46:53 -0300 >MIME-Version: 1.0 >Received: from marauder.illiana.net ([64.212.212.35]) by >bay0-mc5-f15.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); Wed, >25 Jul 2007 13:48:33 -0700 >Received: (qmail 21361 invoked by uid 1484); 25 Jul 2007 19:48:32 -0000 >Received: from 127.0.0.1 by marauder (envelope-from >, uid 71) with qmail-scanner-2.01 >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.24005 >secs); 25 Jul 2007 19:48:32 -0000 >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; 25 >Jul 2007 19:48:31 -0000 >Received: (qmail 21183 invoked by uid 1484); 25 Jul 2007 19:48:06 -0000 >Received: from 209.85.134.190 by marauder >(envelope-from, uid 71) with qmail-scanner-2.01 >(clamdscan: 0.84/2481. Clear:RC:0(209.85.134.190):. Processed in 0.163706 >secs); 25 Jul 2007 19:48:06 -0000 >Received: from mu-out-0910.google.com (209.85.134.190)by 0 with SMTP; 25 >Jul 2007 19:48:05 -0000 >Received: by mu-out-0910.google.com with SMTP id w9so329762muefor >; Wed, 25 Jul 2007 13:46:53 -0700 (PDT) >Received: by 10.82.105.13 with SMTP id d13mr858736buc.1185396413325;Wed, 25 >Jul 2007 13:46:53 -0700 (PDT) >Received: by 10.82.111.6 with HTTP; Wed, 25 Jul 2007 13:46:53 -0700 (PDT) >X-Message-Info: >LsUYwwHHNt3660MmjhEvYg2f34OAemlK+ZzoV09lDsZmbz8QigGIQtU5Yvr3lK0P >Return-Path: >Delivered-To: mailman-app_rpt at lists.illiana.net >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=OTn4MQO/ZeYDnLLaFVrfGyOKcyQ0kSy2jnvosLpv3Ah2f85AQOZBl04BaVXpoPjSP1VPLPElHDM7lMH1AXWv4GNy5kh+lqeZxjPMOvl66i0K1k0CSZ9V5Nl1LmSPr5c1/4oPZGhSk+jWP7Nay6BAZSPtJSwUPTUc03HA9cHL0Es= >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; >s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=E4amHDpPHKNrkpJxcZ1EdfCmmLG3jrN2NqxKCMf1TFoPyCUjRMh1IrB4lZd5eLz7oX4JGL6CnsiMwGevAkKACzfd5RL1S0856WR/RN6VTmNClKQBujGVO5mgfKPKgmOelIR+5O0rG3VgBH7sgTW11Vwd8VvrD1nT06Rrh6nWTds= >References: > >X-BeenThere: app_rpt at lists.illiana.net >X-Mailman-Version: 2.1.6 >Precedence: list >List-Id: Asterisk Repeater Controler >List-Unsubscribe: >, >List-Archive: >List-Post: >List-Help: >List-Subscribe: >, >Errors-To: app_rpt-bounces at lists.illiana.net >X-OriginalArrivalTime: 25 Jul 2007 20:48:33.0524 (UTC) >FILETIME=[2A4F5B40:01C7CEFD] > >Do you use MSN messenger... because I live in Brazil and my spoken English >isn't very good... I'm sure you have trouble to understand everything I >write... > >Thanks > >2007/7/25, Jim Duuuude : >> >>This should not be too difficult at all, if I understand this. If you >>could, >>please email me >>(at my private address telesistant at hotmail.com, not the list) your phone >>number, and >>we can discuss this in real time. >> >> >> >From: "Renato Ornelas" >> >Reply-To: Asterisk Repeater Controler >> >To: "Asterisk Repeater Controler" >> >Subject: Re: [App_rpt] Can't monitor on node >> >Date: Wed, 25 Jul 2007 16:43:19 -0300 >> >MIME-Version: 1.0 >> >Received: from marauder.illiana.net ([64.212.212.35]) by >> >bay0-mc10-f6.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); >>Wed, >> >25 Jul 2007 12:46:13 -0700 >> >Received: (qmail 30315 invoked by uid 1484); 25 Jul 2007 18:46:10 -0000 >> >Received: from 127.0.0.1 by marauder (envelope-from >> >, uid 71) with qmail-scanner-2.01 >> >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in 0.112553 >> >secs); 25 Jul 2007 18:46:10 -0000 >> >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; >>25 >> >Jul 2007 18:46:09 -0000 >> >Received: (qmail 30246 invoked by uid 1484); 25 Jul 2007 18:45:27 -0000 >> >Received: from 64.233.182.189 by marauder >> >(envelope-from, uid 71) with >>qmail-scanner-2.01 >> >(clamdscan: 0.84/2481. Clear:RC:0(64.233.182.189):. Processed in >>0.225549 >> >secs); 25 Jul 2007 18:45:27 -0000 >> >Received: from nf-out-0910.google.com (64.233.182.189)by 0 with SMTP; 25 >> >Jul 2007 18:45:26 -0000 >> >Received: by nf-out-0910.google.com with SMTP id g13so18369nfbfor >> >; Wed, 25 Jul 2007 12:43:20 -0700 (PDT) >> >Received: by 10.82.174.20 with SMTP id w20mr831865bue.1185392599658;Wed, >>25 >> >Jul 2007 12:43:19 -0700 (PDT) >> >Received: by 10.82.111.6 with HTTP; Wed, 25 Jul 2007 12:43:19 -0700 >>(PDT) >> >X-Message-Info: >> >txF49lGdW41gOGAMLIbhiGFrGOY9OuthBCWjMKFq2DxUuTGHkmWauyVMy/Ym/xAD >> >Return-Path: >> >Delivered-To: mailman-app_rpt at lists.illiana.net >> >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; >> >> >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=NHv0l4ZBzd34R+0jsijNJ+LkvPSEr2LAZLFVW5xlR/FjhL2tN0okAqZ/uJzu0lx5woMQ+74FEIEiYD+HUAOzHf1/H7Tk5KAYmTTdJV7V+UxFeNkm4GbxxdtV9AVk0BKQdZ8e7yXrNhE+zxoai2nyvOew7FeXFG0stDUtIVfDTCk= >> >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; >> >> >s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=K/i4cCsXp7kkZob544NlaphWsSH8T7RDqnRLUXX03VlCFKdPbp6woH7Y0FKfZisaUiTmibl3+wMLYyaryRf9AyFBf3ByksQ+MXaSdNFFhfTRzzsHtXhM9JyJEk8bgH9OHcbUw9sVwovydzsz8FuyTtcJIVUlkP58w/X8KtYpMZU= >> >References: >> >< >>BAY119-F303A3F5827241AD48470C5B1F10 at phx.gbl> >> >X-BeenThere: app_rpt at lists.illiana.net >> >X-Mailman-Version: 2.1.6 >> >Precedence: list >> >List-Id: Asterisk Repeater Controler >> >List-Unsubscribe: >> >,>app_rpt-request at lists.illiana.net?subject=unsubscribe> >> >List-Archive: >> >List-Post: >> >List-Help: >> >List-Subscribe: >> >,>app_rpt-request at lists.illiana.net?subject=subscribe> >> >Errors-To: app_rpt-bounces at lists.illiana.net >> >X-OriginalArrivalTime: 25 Jul 2007 19:46:13.0594 (UTC) >> >FILETIME=[752353A0:01C7CEF4] >> > >> >Wow.. your solution is so incredible that I'm amazed... I'd like to hear >> >from you what the possibilities are. Maybe there is a better way to make >>my >> >network.... >> > >> >I'm my scenario the guy with the portable radio press the PTT and this >>info >> >gets to a management console so that the operator knows that ID 1234 in >> >node >> >1999 has just pushed the PTT. >> > >> >Something like this... >> > >> >RANDOM GUY -> RADIO->QUADPCI ---------------------- REMOTE ASTERISK -> >> >management console >> > >> >Any way, if i can get this ID associated with the respective channel in >>the >> >quadradio, I can relay it to the console... >> > >> >The console does not exist yet. >> > >> >Other thing I could you is ID spoof, so the quadradio passes the ID it >> >receives via IAX or SIP. >> > >> >Thanks again. >> >Renato >> >2007/7/25, Jim Duuuude : >> >> >> >>MDC-1200.. that we can decode easily.. but in what manner do you want >>it >> >>passed to another >> >>repeater. and what to do with it there?? >> >> >> >> >> >> >From: "Renato Ornelas" >> >> >Reply-To: Asterisk Repeater Controler >> >> >To: "Asterisk Repeater Controler" >> >> >Subject: Re: [App_rpt] Can't monitor on node >> >> >Date: Wed, 25 Jul 2007 08:53:07 -0300 >> >> >MIME-Version: 1.0 >> >> >Received: from marauder.illiana.net ([64.212.212.35]) by >> >> >bay0-mc10-f8.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2668); >> >>Wed, >> >> >25 Jul 2007 04:53:24 -0700 >> >> >Received: (qmail 6067 invoked by uid 1484); 25 Jul 2007 10:53:21 >>-0000 >> >> >Received: from 127.0.0.1 by marauder (envelope-from >> >> >, uid 71) with qmail-scanner-2.01 >> >> >(clamdscan: 0.84/2481. Clear:RC:1(127.0.0.1):. Processed in >>0.050474 >> >> >secs); 25 Jul 2007 10:53:21 -0000 >> >> >Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with >>SMTP; >> >>25 >> >> >Jul 2007 10:53:21 -0000 >> >> >Received: (qmail 6000 invoked by uid 1484); 25 Jul 2007 10:53:12 >>-0000 >> >> >Received: from 209.85.134.190 by marauder >> >> >(envelope-from, uid 71) with >> >>qmail-scanner-2.01 >> >> >(clamdscan: 0.84/2481. Clear:RC:0(209.85.134.190):. Processed in >> >>0.045554 >> >> >secs); 25 Jul 2007 10:53:12 -0000 >> >> >Received: from mu-out-0910.google.com (209.85.134.190)by 0 with SMTP; >>25 >> >> >Jul 2007 10:53:11 -0000 >> >> >Received: by mu-out-0910.google.com with SMTP id w9so168324muefor >> >> >; Wed, 25 Jul 2007 04:53:08 -0700 (PDT) >> >> >Received: by 10.82.136.4 with SMTP id >>j4mr364511bud.1185364387131;Wed, >> >>25 >> >> >Jul 2007 04:53:07 -0700 (PDT) >> >> >Received: by 10.82.111.6 with HTTP; Wed, 25 Jul 2007 04:53:07 -0700 >> >>(PDT) >> >> >X-Message-Info: >> >> >txF49lGdW40wFwR9dlynL+Bs/CSQlSh7q6wN9n27ktXY//w4DLvEz/vHba9TlyjO >> >> >Return-Path: >> >> >Delivered-To: mailman-app_rpt at lists.illiana.net >> >> >DKIM-Signature: a=rsa-sha1; c=relaxed/relaxed; d=gmail.com; >> >> >> >> >> >s=beta;h=domainkey-signature:received:received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=ShAt5adC/lNgPlRjTRau0KzAD3HJ+LIbCJ8385Td2EMyoMRW/Ppb12k5fi9Gu+sYwUObjF8Tr+ZUnOadqucv1BID5CFuAcWpk5YbqenE9R1Urx26uW3zIUedPOaStLcjSd/B7yZ06QCH+cA3PwwfUS+ACBtTpHq0OlCLkwz2aBY= >> >> >DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; >> >> >> >> >> >s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:references;b=sNijDh5T2PkdrjizCqTBZWVkryyTvIQ1uMc5xRViqercGaLaeGs9KJJIEVjO8FZhrTbHVTOU5/7zOzcnyqLWmW9FO37rkn0e7u3K+3VXOWtPUIF4FfT78vmQvnlulpJkz2TgtU/xQMr/SYkF+dPl+p8Y0y7vCo6qy6rkEH9Rom0= >> >> >References: >> >> >< >> >>4693DFB4.1020101 at rodgers.sdcoxmail.com>< >> >>d10818e80707240524q29a438c1h90dcad085e0494fd at mail.gmail.com>< >> >>46A617D7.2090200 at rodgers.sdcoxmail.com>< >> >>d10818e80707241046m2d739241vfc69d9eed62c9aaa at mail.gmail.com>< >> >>d10818e80707241232r47a3bc47x7e67838a014476ee at mail.gmail.com>< >> >>46A676E7.102 at rodgers.sdcoxmail.com> >> >> >X-BeenThere: app_rpt at lists.illiana.net >> >> >X-Mailman-Version: 2.1.6 >> >> >Precedence: list >> >> >List-Id: Asterisk Repeater Controler >> >> >List-Unsubscribe: >> >> >,> >>app_rpt-request at lists.illiana.net?subject=unsubscribe> >> >> >List-Archive: >> >> >List-Post: >> >> >List-Help: >> >> >List-Subscribe: >> >> >,> >>app_rpt-request at lists.illiana.net?subject=subscribe> >> >> >Errors-To: app_rpt-bounces at lists.illiana.net >> >> >X-OriginalArrivalTime: 25 Jul 2007 11:53:24.0769 (UTC) >> >> >FILETIME=[68002910:01C7CEB2] >> >> > >> >> >Stephen, >> >> > >> >> >The PTT-ID info gets encoded by the radio using MDC-1200 ( >> >> >http://en.wikipedia.org/wiki/MDC-1200). Does app_rpt have something >>like >> >> >this so you can point me the direction to start making the >>modifications >> >>to >> >> >suit my applications? >> >> > >> >> >Sorry to bother you (again), but this is a very huge project and the >> >>time >> >> >is >> >> >very short. I need this ID stuff to deliver the first prototype the >> >>field >> >> > >> >> >Thanks in Advance, >> >> >Renato >> >> > >> >> > >> >> >2007/7/24, Stephen Rodgers : >> >> >> >> >> >>Renato, >> >> >> >> >> >>app_rpt.c would have to be modified to accept the DTMF sequences. >>There >> >> >>is no support in app_rpt.c to do this. >> >> >> >> >> >>Steve. >> >> >> >> >> >> >> >> >> >> >> >>Renato Ornelas wrote: >> >> >> > Actually what I need is: >> >> >> > >> >> >> > The remote radio send its ID when I press the PTT... I want to >> >>receive >> >> >>this >> >> >> > ID and pass it to another repeater. I believe the ID comes as a >> >>DTMF. >> >> >>Can >> >> >> > the quadradio receive (and decode this remote radio ID)? >> >> >> > >> >> >> > Thanks again.. >> >> >> > >> >> >> > Renato Ornelas >> >> >> > >> >> >> > >> >> >> > >> >> >> >>------------------------------------------------------------------------ >> >> >> > >> >> >> > _______________________________________________ >> >> >> > App_rpt mailing list >> >> >> > App_rpt at lists.illiana.net >> >> >> > http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >> >> >> >>_______________________________________________ >> >> >>App_rpt mailing list >> >> >>App_rpt at lists.illiana.net >> >> >>http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >> >> >> >> >> >> >> >_______________________________________________ >> >> >App_rpt mailing list >> >> >App_rpt at lists.illiana.net >> >> >http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >> >> >> >>_______________________________________________ >> >>App_rpt mailing list >> >>App_rpt at lists.illiana.net >> >>http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >> >> >> >_______________________________________________ >> >App_rpt mailing list >> >App_rpt at lists.illiana.net >> >http://lists.illiana.net/mailman/listinfo/app_rpt >> >> >>_______________________________________________ >>App_rpt mailing list >>App_rpt at lists.illiana.net >>http://lists.illiana.net/mailman/listinfo/app_rpt >> >_______________________________________________ >App_rpt mailing list >App_rpt at lists.illiana.net >http://lists.illiana.net/mailman/listinfo/app_rpt