[App_rpt-users] TM-271 remote base setup

[Scott Weis]

I can see when the commands are given that there are no responses from the 
radio. Like I said I think there is a sequence missing, I believe there 
should be some control character that wakes up the radio for serial data, 
which is not being sent from app_rpt.c. I am running  version 0.203 
9/12/2009. Here is the output of the debug:

[Sep 29 11:56:13] WARNING[12195]: chan_usbradio.c:1436 hidthread: Loaded 
parameters from usbradio_tune_usb1.conf for device usb1 .
[Sep 29 11:56:13] NOTICE[12194]: app_rpt.c:4040 openserial: Opened serial 
port /dev/ttyS0
[Sep 29 11:56:13] NOTICE[12205]: app_rpt.c:4230 send_usb_txt: send_usb_txt 
SETFREQ 0.0 0.0 0.0 0.0 L
[Sep 29 11:56:13] NOTICE[12205]: app_rpt.c:11117 serial_remote_io: 
ioport=/dev/ttyS0 baud=13 iofd=0x46
[Sep 29 11:56:14] WARNING[12205]: app_rpt.c:11140 serial_remote_io: Serial 
device not responding on node 2555
[Sep 29 11:56:14] NOTICE[12205]: app_rpt.c:11117 serial_remote_io: 
ioport=/dev/ttyS0 baud=13 iofd=0x46
[Sep 29 11:56:15] WARNING[12205]: app_rpt.c:11140 serial_remote_io: Serial 
device not responding on node 2555
[Sep 29 11:56:15] NOTICE[12205]: app_rpt.c:11117 serial_remote_io: 
ioport=/dev/ttyS0 baud=13 iofd=0x46
[Sep 29 11:56:16] WARNING[12205]: app_rpt.c:11140 serial_remote_io: Serial 
device not responding on node 2555
[Sep 29 11:56:16] NOTICE[12205]: app_rpt.c:11117 serial_remote_io: 
ioport=/dev/ttyS0 baud=13 iofd=0x46
[Sep 29 11:56:17] WARNING[12205]: app_rpt.c:11140 serial_remote_io: Serial 
device not responding on node 2555
[Sep 29 11:56:17] NOTICE[12205]: app_rpt.c:11117 serial_remote_io: 
ioport=/dev/ttyS0 baud=13 iofd=0x46
[Sep 29 11:56:18] WARNING[12205]: app_rpt.c:11140 serial_remote_io: Serial 
device not responding on node 2555
[Sep 29 11:56:18] NOTICE[12205]: app_rpt.c:6616 wait_interval: Delay 
interval = 1000
[Sep 29 11:56:19] NOTICE[12205]: app_rpt.c:6620 wait_interval: Delay 
complete
    -- <Zap/pseudo-94643657> Playing 'rpt/invalid-freq' (language 'en')

----- Original Message ----- >
> What version of app_rpt.c are you running?
>
> I'm no the expert on the TM-271 code or its protocol, but after a brief
> look, it seems to me like the code is attempting send a VF command
> (which it should do) and is never receiving an acknowledge response from
> the radio!  This explains the 5 VF attempts seen in the capture as the
> Kenwood retry count is set to 5 in the code. You should be able to
> confirm this by going in to the Asterisk CLI and sending the  CLI command:
>
> rpt debug level 5
>
> Then connect to the remote base and capture the cli output.
>
> Another thing to try is to monitor the serial data going from the radio
> back to the PC and try to see if you can see any acknowledgement data
> being transmitted by the radio.
>
> Steve
> WA6ZFT
>
>
>