[App_rpt-users] Tx on Rx
Scott Weis
kb2ear at kb2ear.net
Mon Dec 6 22:57:50 UTC 2010
Have you tried duplex=0 in your node stanza? By default is duplex=2 and I
don't see it in your config.
73 de
Scott KB2EAR
-----Original Message-----
From: app_rpt-users-bounces at qrvc.com [mailto:app_rpt-users-bounces at qrvc.com]
On Behalf Of Nathan Roberts (T75)
Sent: Monday, December 06, 2010 5:44 PM
To: app_rpt-users at qrvc.com
Subject: [App_rpt-users] Tx on Rx
I'm using ACID for the first time setting up a remote (simplex) base
station, which I connect to with iaxrpt. ROIP initiated transmit works fine,
but on RF receive COR goes to 1 (from the debug), and immediately TX
activates - as if its trying to operate as a repeater. I've looked through
the settings and am at a loss.
Any advice much appreciated. Config files below.
Regards
Nathan
rpt.conf
; Radio Repeater configuration file (for use with app_rpt) ;
;
; Your Repeater
;
[1999] ; Change this to your assigned node
number
rxchannel = Radio/usb ; Rx audio/signalling channel
irxgain=-10 ; IRLP receive gain adjustment
; Note: Gain is in db-volts
(20logVI/VO)
itxgain=10 ; IRLP transmit gain adjustment
; Note: Gain is in db-volts
(20logVI/VO)
erxgain=-3 ; Echolink receive gain adjustment
; Note: Gain is in db-volts
(20logVI/VO)
etxgain=3 ; Echolink transmit gain adjustment
; Note: Gain is in db-volts
(20logVI/VO)
;controlstates=controlstates ; system control state list
;scheduler=schedule; ; scheduler entries
functions=functions ; Repeater Function Table
phone_functions=functions ; Repeater Function Table
link_functions=functions ; Link Function Table
telemetry=telemetry ; Telemetry descriptions
wait_times=wait-times ; Wait times
context = radio ; dialing context for phone
;;callerid = "Repeater" <0000000000> ; callerid for phone calls
;;idrecording = |iid ; id recording or morse string
;;accountcode=RADIO ; account code (optional)
hangtime=50 ; squelch tail hang time (in ms)
(optional)
althangtime=4000 ; longer squelch tail
totime=170000 ; transmit time-out time (in ms)
(optional)
;;idtime=540000 ; id interval time (in ms)
(optional)
; The default values for hangtime, time-out time, and id interval time are ;
5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms) ;
respectively
politeid=30000 ; time in milliseconds before ID
timer
; expires to try and ID in the tail.
; (optional, default is 30000).
;;idtalkover=|iid ; Talkover ID (optional)
default is none
;;unlinkedct=ct2 ; unlinked courtesy tone
(optional) default is none
;;remotect=ct3 ; remote linked courtesy tone
(indicates a remote is in the list of links)
;;linkunkeyct=ct8 ; sent when a transmission
received over the link unkeys
;nolocallinkct=0 ; Send unlinkedct instead if another
local node is connected to this node (hosted on the same PC).
;irplann=1 ; Default: 1 = Play irlp connect and
disconnect announcements
; 0 = Disable irlp connect and
disconnect announcements
;eannmode=1 ; Default: 1 = Say only node number
on echolink connects
; 2 = say phonetic call sign only on
echolink connects
; 3 = say phonetic call sign and
node number on echolink connects
[functions]
1=ilink,1 ; Specific link disconnect
2=ilink,2 ; Specific Link connect - monitor
only
3=ilink,3 ; Specific Link connect - transceive
4=ilink,4 ; Enter command mode on a specific
link
5=macro,1 ; Command macros (Defined in the
macro section)
7=ilink,5 ; Link status
984=ilink,7 ; Last node to key us up
950=autopatchup,noct=1,quiet=1,farenddisconnect=1,context=my-ip,exten=s ; ip
address readback (requires CURL and asterisk compiled to use CURL).
80=status,1 ; System info
81=status,2 ; Time
82=status,3 ; app_rpt.c Version
;841=meter,daq-cham-1,1,lm34f ; uChameleon temperature readback on
channel 1 using lm34f meter face.
;842=meter,daq-cham-1,1,batvolts ; uChameleon battery voltage
readback on channel 2 using volts meter face
87=ilink,15 ; long range sensors
;6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
;0=autopatchdn ; Autopatch down
;99=cop,4 ; Test tone
98=cop,6 ; Phone TX key
[telemetry]
; Telemetry entries can be shared across all repeaters, or defined for each
repeater.
; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape
sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1,
freq2, duration, amplitude) ; Single frequencies are created by setting
freq1 or freq2 to zero.
;
; |m - Morse escape sequence
;
; Sends Morse code at the telemetry amplitude and telemetry frequency as
defined in the ; [morse] section.
;
; Follow with an alphanumeric string
;
; |i - Morse ID escape sequence
;
; Sends Morse code at the ID amplitude and ID frequency as defined in the ;
[morse] section.
;
; Follow with an alphanumeric string
ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2=|t(660,880,150,2048)
ct3=|t(440,0,150,4096)
ct4=|t(550,0,150,2048)
ct5=|t(660,0,150,2048)
ct6=|t(880,0,150,2048)
ct7=|t(660,440,150,2048)
ct8=|t(700,1100,150,2048)
remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
remotemon=|t(1209,0,50,2048)
cmdmode=|t(900,903,200,2048)
functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
patchup=rpt/callproceeding
patchdown=rpt/callterminated
;
; Morse code parameters, these are common to all repeaters.
;
[morse]
speed=20 ; Approximate speed in WPM
frequency=800 ; Morse Telemetry Frequency
amplitude=4096 ; Morse Telemetry Amplitude
idfrequency=1065 ; Morse ID Frequency
idamplitude=1024 ; Morse ID Amplitude
;
; This section allows wait times for telemetry events to be adjusted ; A
section for wait times can be defined for every repeater ;
[wait-times]
telemwait=2000 ; Time to wait before sending most
telemetry
idwait=500 ; Time to wait before starting ID
unkeywait=2000 ; Time to wait after unkey before
sending CT's and link telemetry
calltermwait=2000 ; Time to wait before announcing
"call terminated"
;
; This is where you define your nodes which cam be connected to.
;
[nodes]
; Note, if you are using automatic update for allstar link nodes, ; no
allstar link nodes should be defined here. Only place a definition ; for
your locak nodes, and private (off of allstar link) nodes here.
1999 = radio at 127.0.0.1/1999,NONE ; This must be changed to your node
number
; Memories for remote bases
[memory]
; Place command macros here
[macro]
Usbradio.conf
; Usbradio channel driver Configuration File ;
[general]
[usb]
hdwtype=0 ; Leave this set to 0 for USB sound fobs modified
using
; the instructions from usbfob.pdf. Use a setting of
; 1 is for Dingotel/Sph interfaces.
rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator
removed
; Set to 1 for additonal gain if using a low-level
receiver output
;;was 1
rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF
; Do not change this, leave this as a 1
;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted
;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in table
;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted
rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch
mode
;setting usb transmitting during receive, usbinvert breaks transmit
carrierfrom=usb ; no,usb,usbinvert,dsp,vox
; no - no carrier detection at all
; usb - from the COR line on the modified USB sound
fob
; usbinvert - from the inverted COR line on the
modified USB sound fob
; dsp - from RX noise using dsp techniques
; vox - voice activated from RX audio
ctcssfrom=no ; no,usb,dsp
; no - CTCSS decoding, system will be carrier
squelch
; usb - CTCSS decoding using input from USB FOB
; (currently not supported)
; dsp - CTCSS decoding using RX audio in DSP.
; rxdemod option must be set to flat for this to
work.
rxdemod=speaker ; input type from radio: no,speaker,flat
; no - RX audio input not used
; flat - Use RX audio from discriminator (before
de-emphasis)
; speaker - use de-emphasized audio
txprelim=no ; Audio processing on left output channel: no,yes
; no - Audio is not pre-emphasized and limited.
; Suitable for use on a microphone input
; yes - Audio is pre-emphasized and limited.
; Suitable for direct connection to an FM modulator
txlimonly=yes ; Audio limiting with no pre-emphasis on output
channel: no,yes
; no - Audio is not limited.
; yes - Audio is limited.
; Suitable for transmitters with no limiting but
with pre-emphasis.
txtoctype=no ; Transmit tone control type: no,phase,notone
; no - CTCSS tone encoding with no hang time
; phase - encode CTCSS and reverse phase
; AKA ("reverse burst") before unkeying TX
; notone - encode CTCSS and stop sending tone before
unkeying TX
txmixa=voice ; Left channel output:
no,voice,tone,composite,auxvoice
; no - Do not output anything
; voice - output voice only
; tone - CTCSS tone only
; composite - voice and tone
; auxvoice - auxiliary voice output at headphone
level for monitoring
txmixb=no ; Right channel output: no,voice,tone,composite,
auxvoice
; See txmixa above.
invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to
transmit
; This is the collector lead of the 2n4401 on the
modified
; usb sound fob.
; please refer to the howto for the procedure to do
this.
duplex=0 ;was 1 with c&D ; Full Duplex
;rxondelay=20 ; Uncomment and/or adjust for simplex nodes to
eliminate "Ping Ponging"
; or "Relay Racing".
; A positive value here will instruct the usbradio
driver to ignore the
; COR line for a specified number of 20mSec
intervals following the
; release of PTT. Use this only on simplex nodes,
and leave commented
; out for repeaters or other full duplex nodes.
Extensions.conf
[general]
static=yes ; These two lines prevent the command-line interface
writeprotect=yes ; from overwriting the config file. Leave them here.
[globals]
VOIPTERM=yourprovider
HOMENPA=619
NODE=1999
[default]
exten => _1NXXNXXXXXX,1,Dial(IAX2/${VOIPTERM}/${EXTEN},40,L(180000:30000))
exten => _1NXXNXXXXXX,2,Hangup
[radio-secure]
exten => ${NODE},1,rpt,${NODE}
[invalidnum]
exten=s,1,Wait,3
exten=s,n,Playback,ss-noservice
exten=s,n,Wait,1
exten=s,n,Hangup
[radio]
exten=_X11,1,Goto(check_route|${EXTEN}|1);
exten=_NXXXXXX,1,Goto(check_route|1${HOMENPA}${EXTEN}|1)
exten=_1XXXXXXXXXX,1,Goto(check_route|${EXTEN}|1)
[check_route]
exten=_X.,1,Noop(${EXTEN})
; no 800
exten=_1800NXXXXXX,2,Goto(invalidnum|s|1)
exten=_1888NXXXXXX,2,Goto(invalidnum|s|1)
exten=_1877NXXXXXX,2,Goto(invalidnum|s|1)
exten=_1866NXXXXXX,2,Goto(invalidnum|s|1)
; no X00 NPA
exten=_1X00XXXXXXX,2,Goto(invalidnum|s|1)
; no X11 NPA
exten=_1X11XXXXXXX,2,Goto(invalidnum|s|1)
; no X11
exten=_X11,2,Goto(invalidnum|s|1)
; no 555 Prefix in any NPA
exten=_1NXX555XXXX,2,Goto(invalidnum|s|1)
; no 976 Prefix in any NPA
exten=_1NXX976XXXX,2,Goto(invalidnum|s|1)
; no NPA=809
exten=_1809XXXXXXX,2,Goto(invalidnum|s|1)
; no NPA=900
exten=_1900XXXXXXX,2,Goto(invalidnum|s|1)
; okay, route it
exten=_1NXXXXXXXXX,2,Goto(default|${EXTEN}|1)
exten=_X.,2,Goto(invalidnum|s|1)
[my-ip]
exten=s,1,Set(MYADDR=${CURL(http://myip.vg)})
exten=s,2,Wait,1
exten=s,3,SayAlpha(${MYADDR})
exten=s,4,Hangup
[radio-gui]
exten = 1999,1,Rpt,1999|X
_______________________________________________
App_rpt-users mailing list
App_rpt-users at qrvc.com
http://qrvc.com/mailman/listinfo/app_rpt-users
More information about the App_rpt-users
mailing list