[App_rpt-users] Low Band Remote Base

[Monty]

Just upgraded remotely, and will try it this evening.  Thanks Jim.

Monty


On Fri, Dec 16, 2011 at 2:27 PM, Jim Duuuude <telesistant at hotmail.com>wrote:

>  If it was, you would know.
>
> Please follow the instructions at the following link:
>
> https://allstarlink.org/support.html#astupgrade
>
> ------------------------------
> From: monty at ke7jvx.com
> Date: Fri, 16 Dec 2011 14:19:36 -0700
>
> Subject: Re: [App_rpt-users] Low Band Remote Base
> To: telesistant at hotmail.com
> CC: app_rpt-users at ohnosec.org
>
>
> I may not be.  Is there a way to check the version via CLI?
>
> Monty
>
>
> On Fri, Dec 16, 2011 at 12:32 PM, Jim Duuuude <telesistant at hotmail.com>wrote:
>
>  are you using the current sources from SVN?
>
> ------------------------------
> From: monty at ke7jvx.com
> Date: Fri, 16 Dec 2011 11:55:17 -0700
> To: app_rpt-users at ohnosec.org
> Subject: Re: [App_rpt-users] Low Band Remote Base
>
>
> Been working off list with David on this issue.  Tried the manual split in
> the memory channel:
>
> *06 = 53.720,136.5,1000,h-t
>
> *Still will only do a 0.5 mhz split, even tried 2000 just to make sure.
> In Checking the source, it looks like that only applies to Kenwood radios
> in 2m/70cm.  My question is could this capability be added to accommodate
> the low band Syntors with the Xcat?
>
> Monty
>
>
> On Sat, Dec 10, 2011 at 9:42 PM, David KE6UPI <dshaw at ke6upi.com> wrote:
>
> it does look like 2/70 and kenwood only.
>
>
> David
>
>
> On Fri, Dec 9, 2011 at 8:42 PM, Monty <monty at ke7jvx.com> wrote:
>
> I searched app_rpt.c and found this:
>
> *static int setkenwood(struct rpt *myrpt)
> {
> char rxstr[RAD_SERIAL_BUFLEN],txstr[RAD_SERIAL_BUFLEN],freq[20];
> char mhz[MAXREMSTR],offset[20],band,decimals[MAXREMSTR],band1,band2;
> int myrxpl,mysplit,step;
>
> int offsets[] = {0,2,1};
> int powers[] = {2,1,0};
>
>     if (sendrxkenwood(myrpt,"VMC 0,0\r",rxstr,"VMC") < 0) return -1;
>     split_freq(mhz, decimals, myrpt->freq);
>     mysplit = myrpt->splitkhz;
>     if (atoi(mhz) > 400)
>     {
>         band = '6';
>         band1 = '1';
>         band2 = '5';
>         if (!mysplit) mysplit = myrpt->p.default_split_70cm;
>     }
>     else
>     {
>         band = '2';
>         band1 = '0';
>         band2 = '2';
>         if (!mysplit) mysplit = myrpt->p.default_split_2m;
>     }*
>
> Looks to be only for 2m and 70cm.
>
> Monty
>
>
>
> On Fri, Dec 9, 2011 at 2:50 PM, David KE6UPI <dshaw at ke6upi.com> wrote:
>
> You can check the code (app_rpt.c) and see if there. I bet it is. I don't
> think Jim would have limit for just 2m/70cm bands.
>
> David
>
>
> On Fri, Dec 9, 2011 at 12:03 PM, Monty <monty at ke7jvx.com> wrote:
>
> I know in the config program there is a split that is set, so I might have
> to play with that.  From the webpage you referenced it looks to be only for
> 2m and 440.
>
> Monty
>
>
>
> On Fri, Dec 9, 2011 at 8:44 AM, David KE6UPI <dshaw at ke6upi.com> wrote:
>
> Hello Monty, Sorry I don't know to much about your hardware. I do know
> that the offset works on my TM-G707 kenwood. Could it be a Syntor problem?
>
> David
>
>
> On Wed, Dec 7, 2011 at 8:02 PM, Monty <monty at ke7jvx.com> wrote:
>
> Hey David,
> Thanks for your response.  I tried this:
>
> *06 = 53.720,136.5,1000,h-t*
>
> When I call it up, it still splits to 0.5 mhz (53.220).  Made sure I
> rebooted the node as well.  So for grins I tried this:
>
> *06 = 53.720,136.5,2000,h-t
> *
> Still it transmits at 53.220 instead of 52.720.
>
>
> Monty
>
>
>
> On Wed, Dec 7, 2011 at 9:26 AM, David KE6UPI <dshaw at ke6upi.com> wrote:
>
> Check out this webpage.
>
> http://ohnosec.org/drupal/node/175
>
> You may also specify the offset in a memory channel
> by adding an additional parameter before the options,
> for example:
>
> 01 = 147.435,103.5,1035,h-t  ; This would be for W6NUT in Los Angeles with input of 146.40
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> David
>
> On Sun, Dec 4, 2011 at 2:37 PM, Monty <monty at ke7jvx.com> wrote:
>
> Hello Everyone,
> I have successfully integrated a Low Band Syntor X with an Xcat to app_rpt
> using CI-V.  I have a problem though.  There are currently 6 6m repeaters
> here in Arizona, 3 have 0.5 mhz split and the other 3 have 1 mhz splits.  I
> have only been successful in programing the 0.5 split frequencies in
> App_Rpt memories.  Is there a trick to make it split to 1 mhz or is that
> not possible?
>
> Monty
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>
>
>
>
>
>
>
>
>
> _______________________________________________ App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20111216/47563a33/attachment.html>