[App_rpt-users] Allstar RTCM (Radio Thin Client Module) isnowavailable

Thu Dec 22 18:44:32 UTC 2011

Jim,

You are the only guy in the cell store shopping for slow and weak
coverage!  "yes, but I need it crappy, lots of hops.  Don't you
understand"  (cell guy staring back)

Pete

From: Jim Duuuude [mailto:telesistant at hotmail.com] 
Sent: Thursday, December 22, 2011 10:27 AM
To: Peter Elke; Marshall Oldham; app_rpt mailing list
Subject: RE: [App_rpt-users] Allstar RTCM (Radio Thin Client Module)
isnowavailable

Pete

In fact a Cradlepoint CTR-500 (TravelRouter) and a Virgin Mobile USB
cellular 3G wireless
module is exactly what I have here, and is what I used for testing of
the RTCM in the
mobile/cellular environment. 

The router is VERY cute and small, and sits nicely on top of the RTCM
(its even smaller then
the RTCM). It, like the RTCM is designed to be low power and is a nice
way to go for such
an installation (good for portable use on batteries, etc).

I got my Virgin Mobile card at WalMart, and if you buy one there they
offer a special plan
where for $20 per month you get 1GB of Internet data transfer (WAAAAY
more then enough
for radio usage). In addition, since it is a non-committed prepay plan,
you can only pay for
it on months when you need it. They also have an option, where for $10
you get 10 days
of use and 250MB of data. 

I also chose it for testing, since that particular service from my
particular location up here in
the mountains in the middle of nowhere happens to get no more the "1
bar" of signal
strength on their network, and then only in the "right" spots. In
addition, their connectivity
is double-NATed and hops across the country a couple of times. I wanted
to have a "worst
case scenario" for testing. It great! Even on a latent double-NATed
cellular network, you can
just plug the RTCM into it without any special provisioning and it JUST
WORKS.

Anywhere else outside of this immediate area, it has lots of "bars" and
provides very good service.

JIM WB6NIL

________________________________

Subject: RE: [App_rpt-users] Allstar RTCM (Radio Thin Client Module)
isnowavailable
Date: Thu, 22 Dec 2011 18:13:31 +0000
From: pete.elke at esquared.com
To: ke6pcv at cal-net.org; telesistant at hotmail.com;
app_rpt-users at ohnosec.org

Hi Marshall,

My Verizon mobile hot-spot only supplies internet over WiFi so I had to
come up with a way of getting the Ethernet jack on the module connected
up.  The PicoStation is normally used as a small access point but their
software allow it to be reversed as a WiFi bridge (or client).   A
typical use might be to connect a game console to WiFi at a location
where wires are unavailable.  You basically tell PicoStation the SSID
you want to bridge to and like magic you have a wired Ethernet
connection.

A better way for a dedicated setup would be a USB based Cellular WAN fob
connected to a CradlePoint unit.  That would eliminate the WIFi part and
be a direct connection from RTCM to the cellular network. 

Pete/WI6H

From: Marshall Oldham [mailto:ke6pcv at cal-net.org] 
Sent: Thursday, December 22, 2011 9:39 AM
To: Peter Elke; 'Jim Duuuude'; 'app_rpt mailing list'
Subject: RE: [App_rpt-users] Allstar RTCM (Radio Thin Client Module)
isnowavailable

Pete, 

Thanks for the information on how you have been using the RTCM. It seems
that there are many different applications that one can use these RTCM's
for. 

They are kind of universal in nature. Enjoyed the photo of the portable
traveling node. Just had one question about the Ubiquiti PicoStation set
up as a bridge.

Can you give/explain a little more information on it?   I am interested
in how this works to provide the internet for your setup. 

Thanks 

Marshall 

________________________________

	From: Peter Elke [mailto:pete.elke at esquared.com] 
	Sent: Thursday, December 22, 2011 12:44 AM
	To: Marshall Oldham; Jim Duuuude; app_rpt mailing list
	Subject: RE: [App_rpt-users] Allstar RTCM (Radio Thin Client
Module) isnowavailable

	Hi Marshal,

	We have been running two separate test projects with the module
over the last few weeks.  So far they seem very functional and cut down
on node management if your goal is "perma-link" nodes.

	The first project is to take separate sites and merge them into
one frequency (and one big node).  At this point we have two of the
eight cut over and we have worked out the basic mechanics.  We use Micor
receivers and MSX100 transmitters (that may change).  The transmitters
are frequency locked using MSF5000 UHSO units with the reference source
being a GPS's 10Mhz output.  The UHSO creates 14.4Mhz that is fed into
the MCX units.  In our testing it became very clear that all of the
radios need to be identical.

	The voting is very cool, you can watch as is switches between
the receive sites (very quickly, multiple times in a 1 second period)
and the toggling goes unnoticed  on the repeater's output.   

	Our next phase is to create larger overlapping coverage area to
see how it sounds mixed by adding a third site in the middle of the
current two.  At this point we don't have much simulcast data, the
overlap area is quite small.

	The other project is an upgrade to my portable Beagleboard node
that I use traveling.  The old version was an Astro portable driven by a
LOX board.  The Beagle had a USB WiFi to a Verizon hot spot box.  The
upgrade swaps out the beagle for a RTCM and makes the connection from
the road automatic.  To create the internet for the module the old USB
wifi was switched out for a Ubiquiti PicoStation set up as a bridge.
When there is cell coverage it works and when there is no cell coverage
it's dead, simple, easy, no-dialing.  The first road test was today, all
went well other than some LTE Verizon problems.

	Over all very cool stuff...

	Pete WI6H...

	From: app_rpt-users-bounces at ohnosec.org
[mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Marshall Oldham
	Sent: Wednesday, December 21, 2011 12:23 PM
	To: 'Jim Duuuude'; 'app_rpt mailing list'
	Subject: Re: [App_rpt-users] Allstar RTCM (Radio Thin Client
Module) isnowavailable

	Jim, 

	Okay so one server running Allstar node software at a central
location (like my house) can support a dozen RTCM's being used as
"Generic" conventional 

	full duplex (repeaters) radio interfaces on far away hilltops
even if I do not want to use the RTCM GPS-Timing Multi receiver voting
or Simulcast Transmitter features?

	As long as I have some sort of internet connection at the remote
sites back to my house?

	If I understand this correctly this would mean that:

	1) No cost of computer at the radio site.

	2) No worry about the node computer locking up at the remote
radio site and having to reboot or reset it.

	3) No cost other than the RTCM (Radio Thin Client Module) to
setup an Allstar node at the remote radio site. (no computer, no URI,
no Sound FOB) 

	4) If I use the RTCM (Radio Thin Client Module) I have the
ability to setup a normal Allstar node at the present time and then
later if I want to I can upgrade the hilltop 

	for GPS-Timing Multi receiver voting and Simulcast Transmitter
by simply adding a GPS receiver at the site and reconfiguring the
software.

	If so, this seems like a pretty cool little piece of hardware! 

	Marshall - ke6pcv    

________________________________

		From: Jim Duuuude [mailto:telesistant at hotmail.com] 
		Sent: Wednesday, December 21, 2011 11:52 AM
		To: Marshall Oldham; app_rpt mailing list
		Subject: RE: [App_rpt-users] Allstar RTCM (Radio Thin
Client Module) is nowavailable

		Yeah, that's the general idea. The location of the Linux
server running app_rpt/Asterisk can be
		more or less anywhere within Internet connectivity of
all of the receiver and/or transmitter sites.
		Of course, "Internet" can mean either some sort of
public Internet connection, or a privately-provided
		Internet connection (low-cost microwave link(s), etc).

		The only limitation is that an RTCM/Voter module *must*
be located on the same LAN as the Linux
		server, to at least provide a GPS-based timing
reference. A system could be set up with a server
		located in some sort of datacenter "on the ground", and
all the radios could have an RTCM "on the
		hill" with them, and as long as there is Internet
connectivity of some sort between each of them
		and the server, the system will work nicely. That is
providing that there is an RTCM located at
		the server location also (whether or not that particular
RTCM has radio hardware connected to it
		or not).

		One minimal Linux server can easily support 1 or 2 dozen
RTCM's (on 1 or 2 allstar nodes),
		and a larger server could easily support MANY dozens of
them on dozens of allstar nodes.
		Of course, you REALLY dont want to put too many of them
on a single server, being a potential
		single point of failure. For pretty much any practical
purpose, the reasonable limitation is
		the point of failure/redundancy issue, not technical
limitations.

		I'm not sure if you were clear on this, so I thought I
would mention that the RTCM is not just
		usable as a GPS-timing-based Multi-Receiver Voting
system and/or a Simulcast Transmitter system.
		It can also be used as a "generic" radio interface for a
conventional (non-GPS-based) either simplex
		or full duplex (repeater) radio. The advantage of doing
this would be to not have the Linux
		host "on the hill" with the radio (as mentioned above).
In addition, the RTCM allows for 
		portable/mobile operation with a mobile/portable
Internet connection in both the GPS-based
		and non-GPS-based environments. 

		JIM WB6NIL

________________________________

		From: ke6pcv at cal-net.org
		To: app_rpt-users at ohnosec.org
		Date: Wed, 21 Dec 2011 10:54:18 -0800
		Subject: Re: [App_rpt-users] Allstar RTCM (Radio Thin
Client Module) is nowavailable

		I have been looking at the Allstar RTCM (Radio Thin
Client Module) and it really looks like a GREAT product and addition to
the already cool Allstar hardware. 

		Among all the other cool features of the RTCM (Radio
Thin Client Module) like Transmitter Simulcasting and Receiver Voting,
if I understand the documentation 

		correctly you can use this very small Radio Thin Client
Module at a remote radio site to set up an Allstar repeater node if the
site has internet connection without a COMPUTER at the site?

		Then you can point the node on the hilltop back to a
server on the ground somewhere that is easy to get too? 

		How many total sites can you use Radio Thin Client
Modules on and point back to a single server on the ground?  

		If this is the case, All I can say is WOW, how cool!

		73

		Marshall 

________________________________

			From: app_rpt-users-bounces at ohnosec.org
[mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Mark Guibord
			Sent: Sunday, December 18, 2011 11:03 AM
			To: app_rpt-users at ohnosec.org
			Subject: [App_rpt-users] Allstar RTCM (Radio
Thin Client Module) is nowavailable

			Allstar RTCM Radio Thin-Client Module, an
Open-Source VOIP-Based Voting Multi-Receiver and Simulcast Transmit
System is now available for purchase. 

			For more information visit
http://micro-node.com/thin-m1.html 

			Regards,
			Mark Guibord
			Micro-Node International

		_______________________________________________
App_rpt-users mailing list App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20111222/11a03c7d/attachment.html>