[App_rpt-users] CTCSS Drop Out Time

Sun Dec 25 15:41:34 UTC 2011

I got the same results.

Merry Christmas!
73
Jim W7RY

From: Lu Vencl 
Sent: Sunday, December 25, 2011 4:33 AM
To: 'Ken' ; 'Jim Duuuude' ; w7ry at centurytel.net ; 'app_rpt mailing list' 
Subject: RE: [App_rpt-users] CTCSS Drop Out Time

Thanks Ken, but this did not work..

Here is what I did..

[root at KA4EPS-R-Margate xpmr]# cd /usr/src/asterisk/asterisk/channels/xpmr

[root at KA4EPS-R-Margate xpmr]# pwd

/usr/src/asterisk/asterisk/channels/xpmr

[root at KA4EPS-R-Margate xpmr]# make

make: *** No targets specified and no makefile found.  Stop.

[root at KA4EPS-R-Margate xpmr]# make install

make: *** No rule to make target `install'.  Stop.

[root at KA4EPS-R-Margate xpmr]#

I assume I have the correct directory?

From: Ken [mailto:ke2n at cs.com] 
Sent: Sunday, December 25, 2011 12:26 AM
To: 'Lu Vencl'; 'Jim Duuuude'; w7ry at centurytel.net; 'app_rpt mailing list'
Subject: RE: [App_rpt-users] CTCSS Drop Out Time

Lu

You make the change to the file, save it and then go to the Linux command line (usually in the source directory above) and type

make

you will see a number of lines scroll by followed by: 

make[1]: Leaving directory `/usr/src/astsrc/asterisk/main'

+--------- Asterisk Build Complete ---------

+ Asterisk has successfully been built, and

+ can be installed by running:              

 +                                           

 +               make install               

 +-------------------------------------------+

So then you type 

make install

and again a bunch of stuff scrolls by, ending with 

+---- Asterisk Installation Complete -------+

+                                           

+    YOU MUST READ THE SECURITY DOCUMENT    

+                                           

+ Asterisk has successfully been installed. 

+ If you would like to install the sample   

+ configuration files (overwriting any      

+ existing config files), run:              

+                                           

+               make samples                

+                                           

+-----------------  or ---------------------

+                                           

+ You can go ahead and install the asterisk 

+ program documentation now or later run:   +\

+                                           

+              make progdocs                

+                                           

+ **Note** This requires that you have      

+ doxygen installed on your local system    

+-------------------------------------------

The you type 

astres.sh

And you are good to go

Merry Christmas

Ken

From: Lu Vencl [mailto:vencl at att.net] 
Sent: Saturday, December 24, 2011 11:20 PM
To: 'Ken'; 'Jim Duuuude'; w7ry at centurytel.net; 'app_rpt mailing list'
Subject: RE: [App_rpt-users] CTCSS Drop Out Time

Yeap, I was the one that brought that up several months ago, but I never could figure out how to "make / make install"  .

I have no clue what that means.. If someone could help me out with that, I will finally get this to 1200 MS which will cover my Yasue radios.

Thanks!

KA4EPS

From: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Ken
Sent: Saturday, December 24, 2011 9:02 PM
To: 'Jim Duuuude'; w7ry at centurytel.net; 'app_rpt mailing list'
Subject: Re: [App_rpt-users] CTCSS Drop Out Time

Notone AKA chicken burst gives you carrier with no tone at the end.

But some radios are too slow in closing the CTCSS and still make noise.

There was a posting on here a while back that pointed the time delay in: 

/usr/src/asterisk/asterisk/channels/xpmr/xpmr.h

The default is 600 ms.  Some radios might be slower than this.

You could change (increase) it, then  make / make install and restart asterisk.

My Alinco DR-?35 series seem to want to give you a small squelch tail no matter what you do, however.

73

Ken

From: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Jim Duuuude
Sent: Saturday, December 24, 2011 6:17 PM
To: w7ry at centurytel.net; app_rpt mailing list
Subject: Re: [App_rpt-users] CTCSS Drop Out Time

try

txtoctype = notone

in usbradio.conf

JIM WB6NIL

--------------------------------------------------------------------------------

From: w7ry at centurytel.net
To: app_rpt-users at ohnosec.org
Date: Sat, 24 Dec 2011 13:55:51 -0800
Subject: [App_rpt-users] CTCSS Drop Out Time

Anyone know if there is an adjustment of the time the transmitter stays keyed, and the PL tone drops out and where that setting is?

With my rigs, I still here the squelch crash after the repeater drops out. I would like to cut the PL off a little sooner or delay the transmitter a little longer.

BTW, I'm all up and running with the repeater function and the node!  Thanks to all that helped me get past the learning curve!

Thanks!

Merry Christmas

73 Jim W7RY

_______________________________________________ App_rpt-users mailing list App_rpt-users at ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

No virus found in this message.
Checked by AVG - www.avg.com
Version: 2012.0.1901 / Virus Database: 2109/4701 - Release Date: 12/24/11
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20111225/2e45d453/attachment.html>