[App_rpt-users] Help PTT

[FERNANDO VILLARROEL]

Dear.

I have a local ACID config connected with a Motorola GM300 and URI


I am using the follow cable:

URI (USB Radio Interface) to Motorola
Maxtrac, GM300 or M120 16 Pin Repeater

I am trying to doing PTT from a Zoiper Softphone to handy device, but not works (*99), i am follow the next howto:

http://allstarnode.com/viewtopic.php?f=5&t=67

But *99 not works for me.

My usbradio.conf:

[general]

[usb]
hdwtype=0               ; Leave this set to 0 for USB sound fobs modified using
                        ; the instructions from usbfob.pdf. Use a setting of
                        ; 1 is for Dingotel/Sph interfaces.

rxboost=1               ; 0 = 20db attenuator inserted, 1= 20db attenuator removed
                        ; Set to 1 for additonal gain if using a low-level receiver output

rxctcssrelax=1          ; reduce talkoff from radios w/o CTCSS Tx HPF
                        ; Do not change this, leave this as a 1

txctcssdefault=100.0    ; default tx ctcss freq, any frequency permitted

;rxctcssfreqs=100.0     ; rx ctcss freqs in floating point. must be in table
;txctcssfreqs=100.0     ; tx ctcss freqs, any frequency permitted

carrierfrom=dsp         ; no,usb,usbinvert,dsp,vox
                        ; no - no carrier detection at all
                        ; usb - from the COR line on the modified USB sound fob
                        ; usbinvert - from the inverted COR line on the modified USB sound fob
                        ; dsp - from RX noise using dsp techniques
                        ; vox - voice activated from RX audio

ctcssfrom=usb           ; no,usb,dsp
                        ; no - CTCSS decoding, system will be carrier squelch
                        ; usb - CTCSS decoding using input from USB FOB
                        ; (currently not supported)
                        ; dsp - CTCSS decoding using RX audio in DSP.
                        ; rxdemod option must be set to flat for this to work.

rxdemod=flat            ; input type from radio: no,speaker,flat
                        ; no - RX audio input not used
                        ; flat - Use RX audio from discriminator
                        ; speaker - use de-emphasized audio

txprelim=no             ; Audio processing on left output channel: no,yes
                        ; no - Audio is not pre-emphasized and limited.
                        ; Suitable for use on a microphone input
                        ; yes - Audio is pre-emphasized and limited.
txprelim=no             ; Audio processing on left output channel: no,yes
                        ; no - Audio is not pre-emphasized and limited.
                        ; Suitable for use on a microphone input
                        ; yes - Audio is pre-emphasized and limited.
                        ; Suitable for direct connection to an FM modulator

txtoctype=notone        ; Transmit tone control type: no,phase,notone
                        ; no - CTCSS tone encoding with no hang time
                        ; phase - encode CTCSS and reverse phase
                        ; AKA ("reverse burst") before unkeying TX
                        ; notone - encode CTCSS and stop sending tone before unkeying TX
                        ; AKA ("chicken burst")

txmixa=composite        ; Left channel output: no,voice,tone,composite,auxvoice
                        ; no - Do not output anything
                        ; voice - output voice only
                        ; tone - CTCSS tone only
                        ; composite - voice and tone
                        ; auxvoice - auxiliary voice output at headphone level for monitoring

txmixb=no               ; Right channel output: no,voice,tone,composite, auxvoice
                        ; See txmixa above.

invertptt=0             ; Invert PTT 0 = ground to transmit, 1 = open to transmit
                        ; This is the collector lead of the 2n4401 on the modified
                        ; usb sound fob.
                        ; please refer to the howto for the procedure to do this.

duplex=2                ; Full Duplex


I hope you could tell me how i can do or what is the best config for usbradio.conf, URI and Motorola GM300?

I hope any idea.

Fernando.