[App_rpt-users] Long Squelch tail problem

[George Csahanin]

How about setting the RXGAIN in usbradio.conf? That usually fixes this problem for me.

GeorgeC
W2DB


  ----- Original Message ----- 
  From: Bill Hurlock 
  To: Tim Sawyer 
  Cc: app_rpt-users at ohnosec.org list 
  Sent: Friday, October 04, 2013 11:17 AM
  Subject: Re: [App_rpt-users] Long Squelch tail problem


  The 736R seems to be lacking in the HF noise area as I can't make it to the 27000 number the program is looking for. It almost gets there. About 26231. I'll have to run a SQ open point test on the radio and see where the SQ opens. I have the test gear to do that.

  Thanks

   

  Bill Hurlock

   

  From: Tim Sawyer [mailto:tim.sawyer at me.com] 
  Sent: Friday, October 04, 2013 10:49 AM
  To: Bill Hurlock
  Cc: app_rpt-users at ohnosec.org list
  Subject: Re: [App_rpt-users] Long Squelch tail problem

   

  Wouxon HTs seem to do that even on systems with perfectly good squelch. Maybe they slowly reduce the transmit power or something. It seems worse when you're close to the receiver. 

   

  As far as your usbradio long squelch tail problem; some radios just don't have enough high frequency noise to drive the DSP properly. In that case you have to use simpleUSB.

   

  Also please note that even with a properly working DSP squelch quickly kerchunking will produce a long squelch tail... just like MICOR squelch will do. 

  --

  Tim

  :wq

   

  On Oct 4, 2013, at 7:05 AM, Bill Hurlock <bill.hurlock at cpcomms.com> wrote:





  I have tried tightening the SQ but then I start to have decode issues with some of the connecting radios. The current signal strength reading, no carrier present, is 776 and SQ setting is 900. This does eliminate the SQ tail but I'm sure this is going to affect RX sensitivity over all being so high. There appears to be a very narrow range of SQ levels that provide no SQ tail and decode is fair. Most problematic are the Wouxon radios.

   

  Bill Hurlock

   

  From: Corey Dean [mailto:n3fe at repeater.net] 
  Sent: Friday, October 04, 2013 12:30 AM
  To: Bill Hurlock; app_rpt-users at ohnosec.org
  Subject: RE: Long Squelch tail problem

   

  Have you tried increasing the squelch level?  What is the current squelch level?

   

  Corey  N3FE

   

  From: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Bill Hurlock
  Sent: Thursday, October 03, 2013 7:46 PM
  To: app_rpt-users at ohnosec.org
  Subject: [App_rpt-users] Long Squelch tail problem

   

  I had to go back to my URI interface and my FT-736R. I have it set up to do tone encode and decode using the URI. All the encode and decode are working however when I unkey there is a squelch tail that lasts about 1 to 2 seconds. I'm allowing the URI to determine COR thru DSP. The connections are setup for raw audio both ways with the node supplying the pre and de emphasis. I have played with the settings but nothing changes the problem. It isn't a consistent duration of tail. I know it is in tone decode mode because if I turn tone off on the portable I can't open the squelch thru the node. Anyone have any ideas..

   

  Bill Hurlock

  CPCommunications

  856-234-1661 Office

  856-264-1010 Cell

  www.cpcomms.com

  WA2TQI

   


  -- 
  This message was scanned and is believed to be clean. 
  Click here to report this message as spam.

  _______________________________________________
  App_rpt-users mailing list
  App_rpt-users at ohnosec.org
  http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

   
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20131005/371cd791/attachment.html>