[App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20

Johnny Keeker cypresstower at yahoo.com
Fri Oct 11 19:08:29 UTC 2013 

good man!
JK

From: Bryan D. Boyle <bdboyle at bdboyle.com>
To: app_rpt-users at ohnosec.org 
Sent: Friday, October 11, 2013 2:54 PM
Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20



and if you bridge allstar (superior and more flexible) to IRLP (old 1990s technology held together with patches and gyrations), Mr Cameron will get his shorts in a wad and cancel your credentials (but leave you listed as an active node to hide the fact that his numbers of real nodes is less than it was...).  

yeah, it still has some mindshare (especially amongst the dinosaurs in the ARRL, who refuse to acknowledge that allstar exists...and despite the population of a* approaching that of the older stuff, have refused to list our nodes as such in the repeater directory...),  but progress waits for no man.  


--
BryanSent from my iPad

On Oct 11, 2013, at 1:47 PM, Johnny Keeker <cypresstower at yahoo.com> wrote:


Plug in your URI, RIM, or usb sound device and you will see it pop up on the linux screen
>as [root@~]  radio-tune-menu 
>the radio tune menu will allow you to setup your sound devices provided your .conf files are correct
>ACID is a repeater controller if you have 2 URIs or RIMs  you can bridge your IRLP node  
>beside IRLP configured on an ACID install had some audio level issues. Not sure about
>Xipar but it also had configs for IRLP.  I only tested it on ACID
>p.s. Scott I noticed you seen the publicizing for the RIM
>JK   
>
>
>From: Richard Szajkowski <va3rzs at gmail.com>
>To: Johnny Keeker <cypresstower at yahoo.com> 
>Cc: App_rpt Users <app_rpt-users at ohnosec.org> 
>Sent: Friday, October 11, 2013 1:06 PM
>Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
>
>
>
>How will I know if it works after I plug it in ? Is there a script that I need to run it install it 
>
>
>I am finding the docs out of date or not there at all (some links are dead like for the 4 port card)
>
>
>I know IRLP is not supported any more , sad as I run an IRLP node , and would have liked to run all 3 networks on one computer , to save a port for the 220 repeater 
>
>
>I thank you for all your help , 
>
>Richard Szajkowski 
>
>
>
>On Oct 11, 2013, at 12:43 PM, Johnny Keeker <cypresstower at yahoo.com> wrote:
>
>
>I don't know the device but if it has a CM108 or CM119 chip it will.
>>Personally, I use startech sound fobs. They're easily modifiable 
>>using surface mount components and they're reliable. URI's are very
>>good, but have my eye on the RIM as it has advantages over the URI.
>>JK
>>
>>From: Richard Szajkowski <va3rzs at gmail.com>
>>To: Johnny Keeker <cypresstower at yahoo.com> 
>>Sent: Friday, October 11, 2013 11:42 AM
>>Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
>>
>>
>>
>>Do you know if the signal link USB sound card would work ????  I have ordered a uri , but I was asked if I would host a node for another repeater 
>>
>>Richard Szajkowski 
>>
>>
>>
>>On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower at yahoo.com> wrote:
>>
>>
>>At the least you have success.  It takes about 10 minutes or less, when you first boot
>>>before your node reports to all the other on-line nodes. Some of my nodes 
>>>use a static IP and others DHCP with reserved address.  Let us all know how things
>>>work out for you. 
>>>Good luck Richard
>>>JK
>>>
>>>
>>>From: Richard Szajkowski <va3rzs at gmail.com>
>>>To: Johnny Keeker <cypresstower at yahoo.com> 
>>>Sent: Thursday, October 10, 2013 7:02 PM
>>>Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
>>>
>>>
>>>
>>>I now have what I think is a working system , 
>>>
>>>
>>>For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs 
>>>
>>>
>>>If I tell it to pull down the info from the server for he node it dies
>>>
>>>
>>>I need it on a static IP for port fowarding , just like my other VoIP systems 
>>>
>>>
>>>And I did do the info on the web portal to the best I can, I entered in all the info it requested 
>>>
>>>
>>>I even got to install your device now , this will be here Tuesday because of our long weekend 
>>>
>>>
>>>Thanks for all the help
>>>
>>>Richard Szajkowski 
>>>
>>>
>>>
>>>On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower at yahoo.com> wrote:
>>>
>>>
>>>did you Not Create an installation disk???? 
>>>>I thought you were past that point and sitting at the test prompt
>>>>If you completed the ACID install and got the test prompt 
>>>>the password is 'setup' 
>>>>once your in root type passwd and change it 
>>>>nodesetup.sh   will run the script to push your node config files from the allstar server to 
>>>>your node "provided you created and saved the files prior to your ACID installation"
>>>>JK 
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>From: "zeppelin.1 at netzero.com" <zeppelin.1 at netzero.com>
>>>>To: app_rpt-users at ohnosec.org 
>>>>Sent: Thursday, October 10, 2013 5:20 PM
>>>>Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
>>>>
>>>>
>>>>
>>>>Hello Richard and welcome to the Linux world;
>>>>                                                                  You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM.
>>>>73 Anton/ KC2RQR
>>>>Node 29103
>>>>
>>>>---------- Original Message ----------
>>>>From: app_rpt-users-request at ohnosec.org
>>>>To: app_rpt-users at ohnosec.org
>>>>Subject: App_rpt-users Digest, Vol 56, Issue 20
>>>>Date: Thu, 10 Oct 2013 12:00:01 -0400
>>>>
>>>>Send App_rpt-users mailing list submissions to
>>>>app_rpt-users at ohnosec.org
>>>>
>>>>To subscribe or unsubscribe via the World Wide Web, visit
>>>>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>>or, via email, send a message with subject or body 'help' to
>>>>app_rpt-users-request at ohnosec.org
>>>>
>>>>You can reach the person managing the list at
>>>>app_rpt-users-owner at ohnosec.org
>>>>
>>>>When replying, please edit your Subject line so it is more specific
>>>>than "Re: Contents of App_rpt-users digest..."
>>>>
>>>>
>>>>Today's Topics:
>>>>
>>>>  1. Help with new install (Richard Szajkowski)
>>>>
>>>>
>>>>----------------------------------------------------------------------
>>>>
>>>>Message: 1
>>>>Date: Wed, 9 Oct 2013 18:14:55 -0400
>>>>From: Richard Szajkowski <va3rzs at gmail.com>
>>>>To: "app_rpt-users at ohnosec.org" <app_rpt-users at ohnosec.org>
>>>>Subject: [App_rpt-users] Help with new install
>>>>Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D at gmail.com>
>>>>Content-Type: text/plain; charset=us-ascii
>>>>
>>>>Hello to the group
>>>>
>>>>I am trying to get the computer on line while my interface is shipped 
>>>>
>>>>I downloaded the ISO off the website , followed the prompts , I am not at a prompt 
>>>>Test > 
>>>>
>>>>I did not enter a root password as I was not asked 
>>>>
>>>>I can't find a PDF or anything on 1st time installs 
>>>>
>>>>Any help would be great
>>>>
>>>>Thanks
>>>>
>>>>Richard Szajkowski va3rzs
>>>>
>>>>
>>>>
>>>>------------------------------
>>>>
>>>>_______________________________________________
>>>>App_rpt-users mailing list
>>>>App_rpt-users at ohnosec.org
>>>>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>>
>>>>
>>>>End of App_rpt-users Digest, Vol 56, Issue 20
>>>>*********************************************
>>>>
>>>>____________________________________________________________
>>>>NetZero now offers 4G mobile broadband. Sign up now.
>>>>_______________________________________________
>>>>App_rpt-users mailing list
>>>>App_rpt-users at ohnosec.org
>>>>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>>
>>>>
>>>>
>>>_______________________________________________
>>>>App_rpt-users mailing list
>>>>App_rpt-users at ohnosec.org
>>>>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>>
>>>
>>>
>>
>>
>
>
_______________________________________________
>App_rpt-users mailing list
>App_rpt-users at ohnosec.org
>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>

_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20131011/e938c553/attachment.html>

More information about the App_rpt-users mailing list