[App_rpt-users] Passing DTMF to another controller
C B
harvard5362 at yahoo.com
Sun Sep 8 17:51:58 UTC 2013
Tim
Thank you that was the step I was missing!!!!
After following your instructions it worked.
Chris
________________________________
From: Tim Sawyer <tim.sawyer at me.com>
To: C B <harvard5362 at yahoo.com>
Cc: "app_rpt-users at ohnosec.org" <app_rpt-users at ohnosec.org>
Sent: Sunday, September 8, 2013 10:42 AM
Subject: Re: [App_rpt-users] Passing DTMF to another controller
This works by connecting to the node that has propagate_dtmf=yes (node 29876 in your case). Then do *40 to enter the command mode. From then on any touch tones (except * and #) will pas out the TX. Then press # to exit command mode and then (*10 to) disconnect.
--
Tim
:wq
On Sep 8, 2013, at 10:03 AM, C B <harvard5362 at yahoo.com> wrote:
Hi
>
>I am trying to get DTMF from other ALLSTAR nodes to pass to a controller connected to a node.
>My configuration is a beagle board with the controller on port 2 (another controller will ne on port 1 latter).
>
>I have set in the RPT.CONF
>
>linktolink=yes
>propagate_dtmf=yes
>
>On both nodes.
>
>Below I have copied my RPT.CONF information in case I have placed them in the wrong place or I have a syntax error or some other error.
>
>Thank you in advance for any help.
>
>
>Chris
>
>
>; Radio Repeater configuration file (for use with app_rpt)
>;
>
>;
>; Your
Repeater
>;
>
>[29876] ; Change this to your assigned node number
>rxchannel=Beagle/beagle29876
>duplex=0
>erxgain=-3
>etxgain=3
>;controlstates=controlstates
>scheduler=schedule29876
>morse=morse29876
>macro=macro29876
>functions=functions29876
>phone_functions=functions29876
>link_functions=functions29876
>telemetry=telemetry
>wait_times=wait-times
>context = radio
>callerid = "Repeater" <0000000000>
>idrecording =
|iN6LXX
>accountcode=RADIO
>hangtime=001
>althangtime=100
>totime=170000
>idtime=540000
>politeid=3000
>linktolink=yes
>propagate_dtmf=yes
>idtalkover=|iN6LXX
>unlinkedct=ct2
>remotect=ct3
>linkunkeyct=ct8
>;nolocallinkct=0
>;eannmode=1
>;connpgm=yourconnectprogram
>;discpgm=yourdisconnectprogram
>;lnkactenable=0
>;lnkacttime=1800
>;lnkactmacro=*52
>;lnkacttimerwarn=30seconds
>;remote_inact_timeout=1800
>;remote_timeout=3600
>nounkeyct=1
>;holdofftelem=0
>beaconing=0
>;
>; *** Status Reporting ***
>;
>; Uncomment the either group following two statpost lines to report the status of your node to stats.allstarlink.org
>; depending on whether you are running ACID or Limey Linux.
>; ** For ACID ***
>statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
>statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>; ** For Limey Linux **
>;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
>;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>;
>; Morse code parameters, these are common to all repeaters.
>;
>[morse29876]
>speed=18
>frequency=800
>amplitude=4096
>idfrequency=750
>idamplitude=1024
>[schedule29876]
>;dtmf_function = m h dom mon dow ; ala cron, star is implied
>
>[functions29876]
>1=ilink,1
>2=ilink,2
>3=ilink,3
>4=ilink,4
>5=macro,1
>70=ilink,5
>71=ilink,6
>72=ilink,7
>73=ilink,15
>74=ilink,16
>75=ilink,8
>80=status,1
>81=status,2
>6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
>0=autopatchdn ; Autopatch down
>989=cop,4
>980=status,3
>99=cop,6
>; Place command macros here
>[macro29876]
>
>
>[29877] ; Change this to your assigned node
number
>rxchannel=Beagle/beagle29877
>duplex=0
>erxgain=-3
>etxgain=3
>;controlstates=controlstates
>scheduler=schedule29877
>morse=morse29877
>macro=macro29877
>functions=functions29877
>phone_functions=functions29877
>link_functions=functions29877
>telemetry=telemetry
>wait_times=wait-times
>context = radio
>callerid = "Repeater" <0000000000>
>idrecording = |iN6LXX
>accountcode=RADIO
>hangtime=100
>althangtime=100
>totime=170000
>idtime=540000
>politeid=3000
>linktolink=yes
>propagate_dtmf=yes
>idtalkover=|iN6LXX
>unlinkedct=ct2
>remotect=ct3
>linkunkeyct=ct8
>;nolocallinkct=0
>;eannmode=1
>;connpgm=yourconnectprogram
>;discpgm=yourdisconnectprogram
>;lnkactenable=0
>;lnkacttime=1800
>;lnkactmacro=*52
>;lnkacttimerwarn=30seconds
>;remote_inact_timeout=1800
>;remote_timeout=3600
>nounkeyct=0
>;holdofftelem=0
>beaconing=0
>;
>; *** Status Reporting
***
>;
>; Uncomment the either group following two statpost lines to report the status of your node to stats.allstarlink.org
>; depending on whether you are running ACID or Limey Linux.
>; ** For ACID ***
>statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
>statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>; ** For Limey Linux **
>;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
>;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>;
>; Morse code parameters, these are common to all
repeaters.
>;
>[morse29877]
>speed=18
>frequency=800
>amplitude=4096
>idfrequency=750
>idamplitude=1024
>[schedule29877]
>;dtmf_function = m h dom mon dow ; ala cron, star is implied
>
>[functions29877]
>1=ilink,1
>2=ilink,2
>3=ilink,3
>4=ilink,4
>5=macro,1
>70=ilink,5
>71=ilink,6
>72=ilink,7
>73=ilink,15
>74=ilink,16
>75=ilink,8
>80=status,1
>81=status,2
>6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
>0=autopatchdn ; Autopatch down
>989=cop,4
>980=status,3
>99=cop,6
>; Place command macros here
>[macro29877]
>
>
>[telemetry]
>ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
>ct2=|t(660,880,150,2048)
>ct3=|t(440,0,150,4096)
>ct4=|t(550,0,150,2048)
>ct5=|t(660,0,150,2048)
>ct6=|t(880,0,150,2048)
>ct7=|t(660,440,150,2048)
>ct8=|t(700,1100,150,2048)
>remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
>remotemon=|t(1209,0,50,2048)
>cmdmode=|t(900,903,200,2048)
>functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
>patchup=rpt/callproceeding
>patchdown=rpt/callterminated
>;
>; This section allows wait times for telemetry events to be adjusted
>; A section for wait times can be defined for every
repeater
>;
>[wait-times]
>telemwait=2000
>idwait=500
>unkeywait=2000
>calltermwait=2000
>;
>; This is where you define your nodes which cam be connected to.
>;
>[nodes]
>; Note, if you are using automatic update for allstar link nodes,
>; no allstar link nodes should be defined here. Only place a definition
>; for your locak nodes, and private (off of allstar link) nodes here.
>29876 = radio at 127.0.0.1/29876,NONE
>29877 = radio at 127.0.0.1/29877,NONE
>; Memories for remote bases
>[memory]
>;00 = 146.580,100.0,m
>;01 = 147.030,103.5,m+t
>;02 = 147.240,103.5,m+t
>;03 = 147.765,79.7,m-t
>;04 = 146.460,100.0,m
>;05 = 146.550,100.0,m
>
>#includeifexists custom/rpt.conf
>
> _______________________________________________
>App_rpt-users mailing list
>App_rpt-users at ohnosec.org
>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20130908/b6107312/attachment.html>
More information about the App_rpt-users
mailing list