[App_rpt-users] Linking two nodes together

Mon Dec 8 01:11:53 UTC 2014

It would be in usbradio.conf or simpleusb.conf ,  which ever one you are
using.

;carrierfrom=no   <<<<<<<<<<<<<<<<<<<<use this line loren (uncommented)
;carrierfrom=dsp
;carrierfrom=pp
carrierfrom=ppinvert  <<<<if using this line, change to above or comment
out with a ;
;carrierfrom=usb
;carrierfrom=usbinvert
;carrierfrom=vox

Passing tones is not hard to do but I think you mean dtmf tones and good
luck as they will not pass. If from one app_rpt node to other app_rpt
node for control, you only need to connect in command mode to control
it.

use dtmf:
*4 (#nodenum#) to connect to node in command mode, issue commands, and
use # to exit command mode when you are done.

No need to pass dtmf audio wise from node to node. Commands will travel
in iax stream when in command mode.

...mike/kb8jnm

> -------- Original Message --------
> Subject: Re: [App_rpt-users] Linking two nodes together
> From: Loren Tedford <lorentedford at gmail.com>
> Date: Sun, December 07, 2014 7:29 pm
> To: Chris Curtis <demoman at rollanet.org>
> Cc: app_rpt mailing list <app_rpt-users at ohnosec.org>
> 
> 
> I hate to bug everyone again on the forums here about this but I need to
> also know how to pass through tones from a particular node to the repeater
> node as well... Also cor=no did not work for the repeater side still kinda
> baffled as to why not.. Where does the cor=no go is it the Rpt.conf or is
> it the usbradio.conf file.. Thanks so much for everyone’s help! Oh the
> reason for wanting to pass DTMF through the RX node is to be able to use my
> auto patch that i have set up on the 2 meter side.. Really bites not having
> the duplexers tuned..
> 
> Loren Tedford (KC9ZHV)
> Email: lorentedford at gmail.com
> 
> http://kc9zhv.lorentedford.com
> 
> 
> On Sat, Dec 6, 2014 at 9:04 AM, Chris Curtis <demoman at rollanet.org> wrote:
> 
> > I like to use:
> >
> > COR=NO
> >
> > To make it stop receiving things
> >
> > Chris
> > KB0WLF
> >
> >
> > > -----Original Message-----
> > > From: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-
> > > bounces at ohnosec.org] On Behalf Of mike at midnighteng.com
> > > Sent: Friday, December 05, 2014 4:25 PM
> > > To: app_rpt-users at ohnosec.org
> > > Subject: Re: [App_rpt-users] Linking two nodes together
> > >
> > >
> > > Loren,
> > >
> > > It's really not about what radios you have but the signal logic of the
> > > COR line.
> > >
> > > If the logic for your controller is low=true meaning
> > > a 0v or low voltage level means it is actively receiving,
> > >
> > > The when you disconnect it,
> > >
> > > It will be true and bring up the repeater as if it was rxing a signal
> > > when you disconnect it because it is not getting a high level signal to
> > > say it is inactive.
> > >
> > > So...
> > > when you disconnect it,
> > > change the logic of the signal for cor input so it does not make the
> > > controller think the rx is active after you disconnect it.
> > >
> > > Example set the controller for high=true or a voltage level is a signal
> > > for active rx when/after disconnecting the rx.
> > >
> > > perhaps someone else can explain it better than I.
> > >
> > > ...mike/kb8jnm
> > >
> > >
> > > > -------- Original Message --------
> > > > Subject: Re: [App_rpt-users] Linking two nodes together
> > > > From: Loren Tedford <lorentedford at gmail.com>
> > > > Date: Fri, December 05, 2014 5:02 pm
> > > > To: mike at midnighteng.com
> > > > Cc: app_rpt mailing list <app_rpt-users at ohnosec.org>
> > > >
> > > >
> > > > All of my current radios are CM200s VHF and UHF on both repeater
> > > systems
> > > > node radios are a combination of CM200s and I do have one Maxtrac VHF
> > > > floating around here at the house.. Yes when i disconnect the RX side
> > > or
> > > > turn off the RX radio it seems to hang open the transmitter with a
> > > silent
> > > > hang.. Not sure about the whole cor thing didnt really change any
> > > settings
> > > > on the radios or the URI at least related to cor.. If you have any
> > > ideas
> > > > feel free to let me know will be testing a few things maybe it was
> > > because
> > > > it was in Duplex=2 mode at the tx site when i did this test not sure
> > > when i
> > > > changed the that line in the Rpt.conf to Duplex=1
> > > >
> > > > Loren Tedford (KC9ZHV)
> > > > Email: lorentedford at gmail.com
> > > > http://kc9zhv.lorentedford.com
> > > >
> > > >
> > > > On Fri, Dec 5, 2014 at 12:28 PM, <mike at midnighteng.com> wrote:
> > > >
> > > > >
> > > > >
> > > > > I don't know what you are "unhooking" for the rx at rptr site but
> > > it
> > > > > could perhaps be
> > > > > "if the logic on the cor is inverted",
> > > > > it would say the rx is active when not present/disconnected.
> > > > >
> > > > > ...mike/kb8jnm
> > > > >
> > > > >
> > > > > > -------- Original Message --------
> > > > > > Subject: Re: [App_rpt-users] Linking two nodes together
> > > > > > From: Loren Tedford <lorentedford at gmail.com>
> > > > > > Date: Fri, December 05, 2014 1:14 pm
> > > > > > To: Corey Dean <n3fe at repeater.net>, app_rpt mailing list
> > > > > > <app_rpt-users at ohnosec.org>
> > > > > >
> > > > > >
> > > > > > Corey,
> > > > > > Noticed one problem if i unhook the RX side at the repeater for
> > > some
> > > > > reason
> > > > > > it hangs the transmitter open not sure exactly what i am missing
> > > here but
> > > > > > if you think of some thing let me know love the *2 for connect
> > > think
> > > > > thats
> > > > > > a great idea
> > > > > >
> > > > > >
> > > > > > Loren Tedford (KC9ZHV)
> > > > > > Email: lorentedford at gmail.com
> > > > > > Email: lorentedford at live.com
> > > > > > Email: lorentedford at aol.com
> > > > > > Email: LorenCS at Ltcraft.net
> > > > > > Email: lorentedford at yahoo.com
> > > > > > Email: loren at lorentedford.com <loren at lorentedford.com>
> > > > > > Email: loren at richlandcountycomputers.com
> > > > > > Phone: 618-553-0806
> > > > > > http://www.lorentedford.com
> > > > > > http://www.Ltcraft.net <http://www.ltcraft.net/>
> > > > > > http://www.richlandcountycomputers.com
> > > > > > http://kc9zhv.lorentedford.com
> > > > > >
> > > > > >
> > > > > > On Fri, Dec 5, 2014 at 12:00 PM, Corey Dean <n3fe at repeater.net>
> > > wrote:
> > > > > >
> > > > > > > Unhook the rx from the repeater site and unhook the tx from
> > > your house
> > > > > and
> > > > > > > the. Just connect them together.  You can also disable the rx
> > > at the
> > > > > > > repeater and do a *2 for receive only to the site at your
> > > house.
> > > > > > >
> > > > > > > Corey
> > > > > > >
> > > > > > > On Dec 5, 2014, at 12:54 PM, Loren Tedford
> > > <lorentedford at gmail.com>
> > > > > wrote:
> > > > > > >
> > > > > > > Yes Doug was looking to link via Internet for now till I can
> > > find some
> > > > > one
> > > > > > > that really knows how to tune Duplexers.. lol... yea I have had
> > > bad
> > > > > look
> > > > > > > with 7 different radio communication companies around here
> > > getting this
> > > > > > > done either they lock open the repeater or you cant hear anyone
> > > > > through the
> > > > > > > recieve side of the system.. So my goal was to setup a node at
> > > the
> > > > > house
> > > > > > > for just RX use only and set up the Transmitter at the repeater
> > > site
> > > > > for
> > > > > > > now.. Internet link them Voice over ip node to node.. I have
> > > two URIs
> > > > > and
> > > > > > > two cables however one cable is a repeater cable suppose i
> > > could
> > > > > probably
> > > > > > > use this on the RX side then use the other one for the
> > > transmitter..
> > > > > Just
> > > > > > > guessing Special Thanks goes out to Chris Curtis will try this
> > > > > thanks!! :)
> > > > > > > Any other thoughts or suggestions with this project please let
> > > me
> > > > > know..
> > > > > > >
> > > > > > > Loren Tedford (KC9ZHV)
> > > > > > > Email: lorentedford at gmail.com
> > > > > > > http://kc9zhv.lorentedford.com
> > > > > > >
> > > > > > >
> > > > > > > On Fri, Dec 5, 2014 at 9:50 AM, Doug Crompton
> > > <doug at crompton.com>
> > > > > wrote:
> > > > > > >
> > > > > > >> Do you mean linking via a normal Allstar link? or linking via
> > > RF. It
> > > > > is
> > > > > > >> not clear what you are trying to do.
> > > > > > >>
> > > > > > >> You can link two nodes privately if you know the IP address
> > > and port
> > > > > of
> > > > > > >> each node. You just enter the info for the OTHER node in the
> > > nodes
> > > > > section
> > > > > > >> of rpt.conf. Assuming you have a good Internet path once this
> > > is
> > > > > entered
> > > > > > >> and Asterisk is restarted you should be able to connect. Of
> > > course
> > > > > you also
> > > > > > >> need the port forwards in the routers also.
> > > > > > >>
> > > > > > >> [nodes]
> > > > > > >> ; Note, if you are using automatic update for allstar link
> > > nodes,
> > > > > > >> ; no allstar link nodes should be defined here. Only place a
> > > > > definition
> > > > > > >> ; for your local nodes, and private (off of allstar link)
> > > nodes here.
> > > > > > >>
> > > > > > >> 1998 = radio at ip.address.for.1999:port/1998,NONE
> > > > > > >>
> > > > > > >> This show one end. The other end would be just the opposite.
> > > Port is
> > > > > only
> > > > > > >> needed if it is other than the default 4569.
> > > > > > >>
> > > > > > >>
> > > > > > >>
> > > > > > >> *73 DougWA3DSPhttp://www.crompton.com/hamradio
> > > > > > >> <http://www.crompton.com/hamradio>*
> > > > > > >>
> > > > > > >>
> > > > > > >> ------------------------------
> > > > > > >> Date: Fri, 5 Dec 2014 01:52:39 -0600
> > > > > > >> From: lorentedford at gmail.com
> > > > > > >> To: app_rpt-users at ohnosec.org
> > > > > > >> Subject: [App_rpt-users] Linking two nodes together
> > > > > > >>
> > > > > > >>
> > > > > > >> Need to kinda get some examples of how to link two nodes
> > > together
> > > > > > >> examples lets say node 1 is at the repeater site and node 2 is
> > > at my
> > > > > house
> > > > > > >> and lets say that I cant get some one to tune up my duplexer
> > > > > properly..
> > > > > > >> what is the best way to link two nodes together to make my
> > > repeater at
> > > > > > >> least functional..
> > > > > > >>
> > > > > > >> Thanks in advance
> > > > > > >> Loren Tedford (KC9ZHV)
> > > > > > >> Email: lorentedford at gmail.com
> > > > > > >>
> > > > > > >> http://kc9zhv.lorentedford.com
> > > > > > >>
> > > > > > >>
> > > > > > >> _______________________________________________ App_rpt-users
> > > mailing
> > > > > > >> list App_rpt-users at ohnosec.org
> > > > > > >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To
> > > > > unsubscribe
> > > > > > >> from this list please visit
> > > > > > >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and
> > > scroll
> > > > > > >> down to the bottom of the page. Enter your email address and
> > > press the
> > > > > > >> "Unsubscribe or edit options button" You do not need a
> > > password to
> > > > > > >> unsubscribe, you can do it via email confirmation. If you have
> > > trouble
> > > > > > >> unsubscribing, please send a message to the list detailing the
> > > > > problem.
> > > > > > >>
> > > > > > >> _______________________________________________
> > > > > > >> App_rpt-users mailing list
> > > > > > >> App_rpt-users at ohnosec.org
> > > > > > >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> > > > > > >>
> > > > > > >> To unsubscribe from this list please visit
> > > > > > >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and
> > > scroll
> > > > > > >> down to the bottom of the page. Enter your email address and
> > > press the
> > > > > > >> "Unsubscribe or edit options button"
> > > > > > >> You do not need a password to unsubscribe, you can do it via
> > > email
> > > > > > >> confirmation. If you have trouble unsubscribing, please send a
> > > > > message to
> > > > > > >> the list detailing the problem.
> > > > > > >>
> > > > > > >
> > > > > > > _______________________________________________
> > > > > > > App_rpt-users mailing list
> > > > > > > App_rpt-users at ohnosec.org
> > > > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> > > > > > >
> > > > > > > To unsubscribe from this list please visit
> > > > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and
> > > scroll
> > > > > down
> > > > > > > to the bottom of the page. Enter your email address and press
> > > the
> > > > > > > "Unsubscribe or edit options button"
> > > > > > > You do not need a password to unsubscribe, you can do it via
> > > email
> > > > > > > confirmation. If you have trouble unsubscribing, please send a
> > > message
> > > > > to
> > > > > > > the list detailing the problem.
> > > > > > >
> > > > > > ><hr>_______________________________________________
> > > > > > App_rpt-users mailing list
> > > > > > App_rpt-users at ohnosec.org
> > > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> > > > > >
> > > > > > To unsubscribe from this list please visit
> > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and
> > > scroll down
> > > > > to the bottom of the page. Enter your email address and press the
> > > > > "Unsubscribe or edit options button"
> > > > > > You do not need a password to unsubscribe, you can do it via
> > > email
> > > > > confirmation. If you have trouble unsubscribing, please send a
> > > message to
> > > > > the list detailing the problem.
> > > > > _______________________________________________
> > > > > App_rpt-users mailing list
> > > > > App_rpt-users at ohnosec.org
> > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> > > > >
> > > > > To unsubscribe from this list please visit
> > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and
> > > scroll down
> > > > > to the bottom of the page. Enter your email address and press the
> > > > > "Unsubscribe or edit options button"
> > > > > You do not need a password to unsubscribe, you can do it via email
> > > > > confirmation. If you have trouble unsubscribing, please send a
> > > message to
> > > > > the list detailing the problem.
> > > > >
> > > _______________________________________________
> > > App_rpt-users mailing list
> > > App_rpt-users at ohnosec.org
> > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> > >
> > > To unsubscribe from this list please visit http://ohnosec.org/cgi-
> > > bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the
> > > page. Enter your email address and press the "Unsubscribe or edit
> > > options button"
> > > You do not need a password to unsubscribe, you can do it via email
> > > confirmation. If you have trouble unsubscribing, please send a message
> > > to the list detailing the problem.
> >
> > _______________________________________________
> > App_rpt-users mailing list
> > App_rpt-users at ohnosec.org
> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> >
> > To unsubscribe from this list please visit
> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
> > to the bottom of the page. Enter your email address and press the
> > "Unsubscribe or edit options button"
> > You do not need a password to unsubscribe, you can do it via email
> > confirmation. If you have trouble unsubscribing, please send a message to
> > the list detailing the problem.
> ><hr>_______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> 
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.