[App_rpt-users] no audio from URI

Wed Jun 4 09:42:41 UTC 2014

Have you tried Iain's suggestion to disable the internal audio? See his email.

Thanks,
Bob
kk6ecm

Sent from iPad

On Jun 4, 2014, at 5:24 AM, "torben at klimt-online.com" <torben at klimt-online.com> wrote:

> hi all,
> here the missing information for the machines who don`t work :-(
> is there any ppossibility to run it in the future ? cause the INtel NUC is very nice ;-)
>  
> greetings tom dh6mbt
>  
>  
> PC1:
> Modell   : Intel NUC DC321IYE
> Homepage : http://www.intel.com/content/www/us/en/nuc/nuc-kit-dc3217iye.html
> Processor: Intel Core i3 processor
> Chipset  : Intel QS77 Express Chipset
> 
> PC2 and 3:
> Modell   : Fujitsi Lifebook E780
> Homepage : http://globalsp.ts.fujitsu.com/dmsp/Publications/public/db_profnb_lifebook_e780_de.pdf
> Processor: Intel Core i5 processor
> Chipset  : Intel QM57
>  
>  
> Von: app_rpt-users-bounces at ohnosec.org [app_rpt-users-bounces at ohnosec.org] im Auftrag von torben at klimt-online.com [torben at klimt-online.com]
> Gesendet: Dienstag, 3. Juni 2014 23:33
> An: kk6ecm; App_rpt-users at ohnosec.org
> Betreff: Re: [App_rpt-users] no audio from URI
> 
> IT WORKS NOW
> I tried the next pc (an older one) and it works fine without any config changes. It`s short before midnight and I must go to work tomorrow L
> I will look the next days which CPUs and Chipsets I tried and doesn`t work and which one work now ok ?
>  
> Good n8 tom dh6mbt
>  
> Von: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-bounces at ohnosec.org] Im Auftrag von kk6ecm
> Gesendet: Dienstag, 3. Juni 2014 23:13
> An: App_rpt-users at ohnosec.org
> Betreff: Re: [App_rpt-users] no audio from URI
>  
> Try amplifying the output of the URI in order to drive the speaker. If that does not work, I'd test the URI using a loopback connector and uridiag down loaded from http://www.dmkeng.com/images/URI-FAQs.pdf
> 
> 
> Make sure Asterisk is stopped when uridiag is used. Service asterisk stop on the Linux command line. This is not a test to determine URI health, but the ability of the ACID build on your computer, and the ability to send audio to the URI.
> 
> Thanks,
> Bob
> kk6ecm
>  
> Sent from iPad
>  
> 
> On Jun 3, 2014, at 2:51 PM, "torben at klimt-online.com" <torben at klimt-online.com> wrote:
> 
> Now i tried 3 different computers with 2 URI-Boards and 3 installs
>  
> -          SQL detect by DSP -> ok
> -          DTMF reading -> ok
> -          Transmitting by PTT -> ok
> -          Sending audio -> NO
>  
> I have headphones connectet direct to the URI on Pins 13 (GND) and 22/23 -> no nothing L L
>  
> Von: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-bounces at ohnosec.org] Im Auftrag von kk6ecm
> Gesendet: Dienstag, 3. Juni 2014 14:11
> An: App_rpt-users at ohnosec.org
> Betreff: Re: [App_rpt-users] no audio from URI
>  
> Again, I'm not sure if it is your issue, but the chipset used in your board is of the same family as the one I seemed to have difficulty. When I chose a board with an older generation chipset (NM10, and not the 7x series), the audio worked good.
> 
> Thanks,
> Bob
> kk6ecm
>  
> Sent from iPad
>  
> 
> On Jun 3, 2014, at 4:19 AM, "torben at klimt-online.com" <torben at klimt-online.com> wrote:
> 
> i take this box
>  
> http://www.intel.com/content/dam/www/public/us/en/documents/product-briefs/dc3217iye-product-brief.pdf
>  
> 73 de tom dh6mbt
> Von: app_rpt-users-bounces at ohnosec.org [app_rpt-users-bounces at ohnosec.org] im Auftrag von kk6ecm [kk6ecm at gmail.com]
> Gesendet: Dienstag, 3. Juni 2014 12:59
> An: App_rpt-users at ohnosec.org
> Betreff: Re: [App_rpt-users] no audio from URI
> 
> I'm not sure of your issue, but your experience sounds like mine when I attempted to use a computer with a newer chipset, incompatible withe CentOS 5.10. That was Intel chipset NM 70. When I used a mother board with the older Intel chipset NM 10, I hade no audio issues. I discovered the issue when using DMK Engineering uridiag software on the ACID build (see URI FAQ on the DMK website re uridiag and loopback testing).
> 
> Thanks,
> Bob
> kk6ecm
>  
> Sent from iPad
>  
> 
> On Jun 2, 2014, at 11:01 PM, "torben at klimt-online.com" <torben at klimt-online.com> wrote:
> 
> good morning,
> i connect a headphone to the URI so we don`t need to search the problem on the Motorolas....
>  
> 73...
>  
> Von: David Morley [ab8tn1 at cox.net]
> Gesendet: Dienstag, 3. Juni 2014 07:14
> An: torben at klimt-online.com
> Betreff: Re: [App_rpt-users] no audio from URI
> 
> Are the GM 360s the same as the GM 300s?  Do they have 16 pin connectors 
> 
> Sent from my iPhone
>  
> 
> On Jun 2, 2014, at 2:07 PM, "torben at klimt-online.com" <torben at klimt-online.com> wrote:
> 
> Hi all,
> i think i have a little blackout L
> I would like to set up a repeater with 2 GM360
> <!--[if !supportLists]-->-          <!--[endif]-->SQL detect is ok
> <!--[if !supportLists]-->-          <!--[endif]-->NF to another connectet repeater is ok
> <!--[if !supportLists]-->-          <!--[endif]-->DTMF is ok (looks good on console)
> <!--[if !supportLists]-->-          <!--[endif]-->PTT is ok
> BUT there is no audio out from the URI on Port 22 and or 23 L
> On a windows machine the URI works fine but on the asterisk there is no output
> Any ideas ?
> greetings
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> 
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> 
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> 
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20140604/ef45b81d/attachment.html>