[App_rpt-users] Remote Bases

[R. Wayne]

Where can I find a list of frequency agile radios?

-----Original Message----- 
From: mike at midnighteng.com
Sent: Friday, July 17, 2015 8:16 PM
To: app_rpt-users at ohnosec.org
Subject: Re: [App_rpt-users] Remote Bases


It would be hard to know what type of remote base you are setting up to
help because you did not state it.

Basically, it is just another node.Set-up everything a node needs.

If it is a freq agile remote base you need:

To tell app_rpt what it is and the method of communications (com/usb
ports) to it (except rbi-1 is parport only)

Such as but not limited to depending on remote type-

ioport=/dev/ttyUSB0            ; Serial port for control (usb serial 1)
iospeed=19200                  ; io speed for port
iobase = 0x378                  ; Specify IO port for parallel port
remote=ic706                    ; Remote Radio Type
civaddr=72                    ; ic706 dev address

Command structure for control included in that nodes set-up.
(you may not need all of these depending on what you are using)
0=remote,1           ; Retrieve Memory
1=remote,2           ; Set freq. VFO MMMMM*KKK*O   (Mhz digits, Khz
digits, Offset)
2=remote,3           ; Set tx PL tone PL Tone HHH*D*
3=remote,4           ; Set rx PL tone         HHH*D*

6=remote,6           ; Set mode 1=FM 2=USB 3=LSB 4=AM

40=remote,100        ; Rx PL off
41=remote,101        ; Rx PL on
42=remote,102        ; Tx PL off
43=remote,103        ; Tx PL on
44=remote,104        ; Low Power
45=remote,105        ; Medium Power
46=remote,106        ; High Power

51=remote,5          ; Long status query
52=remote,140        ; Short status query
67=remote,210        ; Send a *
69=remote,211        ; Send a #

79=remote,119        ; Tune (brief AM transmission for automatic antenna
tuner)

711=remote,107       ; Bump -20
714=remote,108       ; Bump -100
717=remote,109       ; Bump -500
713=remote,110       ; Bump +20
716=remote,111       ; Bump +100
719=remote,112       ; Bump +500
721=remote,113       ; Scan - slow
724=remote,114       ; Scan - quick
727=remote,115       ; Scan - fast
723=remote,116       ; Scan + slow
726=remote,117       ; Scan + quick
729=remote,118       ; Scan + fast


If it is a stand alone RB or a party-line type of node...
If one connection at a time, use ",y" at the definition line:
29261 = radio at 127.0.0.1/29261,NONE,y   ;y=remote base


If connecting to it from other node, you will want to use *5(node#) for
control of it from the other node. There are some other ways of doing that
depending on your set-up.

Can't write the book here so I hope that helps some.

...mike/kb8jnm

> Better yet, does anyone have any examples they could share?  Looking to
> have a regular node and remote base on the same server.  I think I have
> most of it right, just want to make sure.
>
> Jamey
> WR4JW
> ________________________________
> From: app_rpt-users-bounces at ohnosec.org
> [app_rpt-users-bounces at ohnosec.org] on behalf of Jamey Wright
> [Jamey.Wright at morgan911.org]
> Sent: Friday, July 17, 2015 8:23 PM
> To: APP RPT ý[app_rpt-users at ohnosec.org]ý
> Subject: [App_rpt-users] Remote Bases
>
> I am getting ready to set up a remote base.  I have been reading through
> the docs on the site and I have most of it but just wanted to verify that
> remote base node stanza info goes into the rpt.conf config file.
>
> Thanks
>
> Jamey
> WR4JW
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
> to the bottom of the page. Enter your email address and press the
> "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.


_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit 
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to 
the bottom of the page. Enter your email address and press the "Unsubscribe 
or edit options button"
You do not need a password to unsubscribe, you can do it via email 
confirmation. If you have trouble unsubscribing, please send a message to 
the list detailing the problem.