[App_rpt-users] Audio detection circuit to generate 'COR'

[Steve Zingman]

Steve,
Be aware that those transmitters are dirty.
There is a note about a module using the same RF circuit on Doug's 
HAMVIOP site.
He suggests a filter. REQUIRED if you are going to drive a amp or even 
connect it to a antenna!

73, Steve N4IRS

On 10/6/2015 9:13 AM, Steven Donegan wrote:
> Thanks. For my first full duplex repeater (for test/learning purposes) 
> I am going with 2 of those modules and a 6 cavity duplexor (likely of 
> the 'notch' variety). If it works out may put my Mirage BD-35 on the 
> TX side before the duplexor and get ~16 watts for giggles.
> Steven Donegan
> KK6IVC General Class FCC License
> Silver State Car #86
> www.sscc.us
>
> ------------------------------------------------------------------------
> *From:* Steve Zingman <szingman at msgstor.com>
> *To:* Steven Donegan <donegan at donegan.org>
> *Sent:* Tuesday, October 6, 2015 6:10 AM
> *Subject:* Re: Audio detection circuit to generate 'COR'
>
> I'll send you the info tonight when I get home. I have a couple of them.
>
>
>
> On 10/6/2015 9:10 AM, Steven Donegan wrote:
>> Thanks Steve! I'll look into that as well.
>> Steven Donegan
>> KK6IVC General Class FCC License
>> Silver State Car #86
>> www.sscc.us <http://www.sscc.us/>
>>
>> ------------------------------------------------------------------------
>> *From:* Steve Zingman <szingman at msgstor.com> 
>> <mailto:szingman at msgstor.com>
>> *To:* Steven Donegan <donegan at donegan.org> 
>> <mailto:donegan at donegan.org>; "app_rpt-users at ohnosec.org" 
>> <mailto:app_rpt-users at ohnosec.org> <app_rpt-users at ohnosec.org> 
>> <mailto:app_rpt-users at ohnosec.org>
>> *Cc:* "app_rpt-users at ohnosec.org" <mailto:app_rpt-users at ohnosec.org> 
>> <app_rpt-users at ohnosec.org> <mailto:app_rpt-users at ohnosec.org>
>> *Sent:* Tuesday, October 6, 2015 6:06 AM
>> *Subject:* Audio detection circuit to generate 'COR'
>>
>> Steve COR or actually RUS "Receiver Un Squelch" is available in that 
>> radio. You have to unsolder the shield to get to it.
>>
>> 73, Steve
>>
>>
>>
>> On 10/6/2015 8:56 AM, Steven Donegan wrote:
>>> Well, it is a generic question - any radio without COR. The specific 
>>> model in my case is a UHF radio module model # SA-828U: 
>>> http://www.alibaba.com/product-detail/1W-5km-distance-SA828-U-uhf_60092524887.html?spm=a2700.7724857.29.62.Xbg6c5
>>> Steven Donegan
>>> KK6IVC General Class FCC License
>>> Silver State Car #86
>>> www.sscc.us <http://www.sscc.us/>
>>>
>>> ------------------------------------------------------------------------
>>> *From:* Skyler Fennell <electricity440 at gmail.com> 
>>> <mailto:electricity440 at gmail.com>
>>> *To:* Steven Donegan <donegan at donegan.org> <mailto:donegan at donegan.org>
>>> *Cc:* app_rpt-users at ohnosec.org <mailto:app_rpt-users at ohnosec.org>
>>> *Sent:* Tuesday, October 6, 2015 5:47 AM
>>> *Subject:* Re: [App_rpt-users] Audio detection circuit to generate 'COR'
>>>
>>> http://www.aaroncake.net/circuits/vidswitch.asp
>>>
>>> That might work, I use it for packet.
>>>
>>> What radio are you on?
>>>
>>> Sent from my iPhone
>>>
>>>
>>>
>>> On Oct 6, 2015, at 6:29 AM, Steven Donegan <donegan at donegan.org 
>>> <mailto:donegan at donegan.org>> wrote:
>>>
>>>> Does anyone have a circuit that will take audio from a radio and 
>>>> generate a pseudo COR signal for the URI-x? If so would you share 
>>>> the circuit diagram?
>>>>
>>>> TIA
>>>> Steven Donegan
>>>> KK6IVC General Class FCC License
>>>> Silver State Car #86
>>>> www.sscc.us <http://www.sscc.us/>
>>>> _______________________________________________
>>>> App_rpt-users mailing list
>>>> App_rpt-users at ohnosec.org <mailto:App_rpt-users at ohnosec.org>
>>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>>
>>>> To unsubscribe from this list please visit 
>>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and 
>>>> scroll down to the bottom of the page. Enter your email address and 
>>>> press the "Unsubscribe or edit options button"
>>>> You do not need a password to unsubscribe, you can do it via email 
>>>> confirmation. If you have trouble unsubscribing, please send a 
>>>> message to the list detailing the problem.
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> App_rpt-users mailing list
>>> App_rpt-users at ohnosec.org <mailto:App_rpt-users at ohnosec.org>
>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>
>>> To unsubscribe from this list please visithttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users  and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
>>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
>>
>>
>>
>
>
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20151006/921725c4/attachment.html>