[App_rpt-users] Echolink connection announcement Volume

[kk6ecm]

Precisely, thanks, and understand that function is not supported. I'm thinking holdofftelem=1 is what I need at the moment. Our net operators want to know who is joining in.

Thanks,
Bob
kk6ecm

Sent from iPad


> On Jan 5, 2016, at 1:03 PM, Jon Rorke <jrorke at cogeco.ca> wrote:
> 
> So what you are looking for is the announcement level to duck to 50 % when somebody is talking at the same time? But normally full level when nobody is talking? Is that what you mean when you say the repeater is in use?
> 
> If so, right now DIAL and ACID distros dont do that.
> 
> What I have done is set telemdefault to2 and holdofftelem=1.
> 
> Setting Telemdefault to 2 makes the telemetry announce if a command is initially sent from the node as per normal, then after a time of inactivity the telemetry goes quiet so you wont hear any connections if somebody connects.
> 
> This is good for ongoing nets so that incoming stations joining don't distract conversations.
> 
> The holdofftelem=1 just holds off any pending announcements its going to make until the transmitting station unkeys.
> 
> If you are looking for the announcements ducking lower when somebody keys, only the XIPPAR distro suports that.
> 
> Jon VA3RQ
> 
>> On 1/5/2016 2:26 PM, kk6ecm wrote:
>> I'll take a look at it. Our issue boils down to the fact all the volumes are the same, announcements and user voice, and we'd like to have the announcements about half the volume when the repeater is in use. I'm looking at holdofftelem=1 as well as http://docs.allstarlink.org/drupal/node/126 to see if we can achieve a workable compromise.
>> 
>> Thanks,
>> Bob
>> kk6ecm
>> 
>> Sent from iPad
>> 
>> 
>> On Jan 5, 2016, at 11:11 AM, Ken <ke2n at cs.com> wrote:
>> 
>>>> The audio was setup using the prescribed method, without the "MK-1
>>> calibrated ear."
>>>> If we raised the rx level, and reduced the tx level, then we'd have
>>>> difficulty hearing the station id. I suspect the level of our custom
>>>> recordings is too high, an I was trying to avoid the brute force method of
>>> redoing each one.
>>>> Thanks,
>>>> Bob
>>>> kk6ecm
>>> Record level is tricky in Asterisk.  When seen on any editing program, "full
>>> scale" is -6 dB f.s. or 0.5 on the voltage scale. I suspect the reason for
>>> this is that uLaw only produces about 14 bits when converted to linear and
>>> that is what asterisk expects for full scale.  (I guess losing those two
>>> bits is equivalent to dividing by four or 6 dB down).  Have a look at some
>>> of the Allison GSM files by importing them into Audacity and you will see
>>> the max level is 0.5.  Even this is too loud for most people (as newbie
>>> postings have indicated many times). I think a reasonable level is 3 dB down
>>> from full scale - in other words, minus 9 dB relative to full scale (!) or
>>> about 0.3 on the voltage scale.
>>> 
>>> Ref: http://images.ohnosec.org/app-rpt-audacity.pdf
>>> 
>>> Regards
>>> Ken
>>> KE2N
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>> 
>> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
> 
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> 
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.