[App_rpt-users] Rpi3 on 29655
ARS W5OMR
ars.w5omr at gmail.com
Mon Feb 19 03:27:28 UTC 2018
I'm at my wit's end...
Somewhere between asterisk -Rcvvvv and modules.conf and 'usbradio.conf
... ARRRHGGG!
I know, you've been there, too - I've not had this stuff up and
running for over 3 years, I've forgotten some of the most important
things I knew...
Steve/N4IRS, great guy that he is, helped me tremendously the other
day and all was 'ok'. It wasn't quite done, but at the time, I felt
confident it was merely minor tweeking... I still had to make an
interface cable for the repeater to the URIx but, even without a radio
connected, I was connecting (monitor mode) to other nodes. That was
cool! It was PROGRESS!
But, the red LED on the URI stayed on. Even though there wasn't a
radio connected, I knew it wasn't supposed to be on. That meant it
was sending the 'xmit' signal out. Hell, even in the node status,
it's saying it's timing out and I don't know where else to tell
allstar that it's not even receiving a signal. First thing I did, was
modify usbradio.conf and inverted PTT and that shut it off. The
voltage on the output of the URI (Pins 1 (PTT) and 13 (GND)) 'floats'
somewhere around 0.65 to 0.72v, but when it's transmitting, it is
pulled DOWN to 0v. That's opposite of inverting PTT from 0 to 1.
(head scratch)
This is on a Raspberry Pi3 connecting to a Motorola R100 repeater.
Here are the .conf files, if someone wouldn't mind having a gander....
iax.conf
----------
; Inter-Asterisk eXchange driver definition
; http://docs.allstarlink.org/drupal/node/15
; ulaw, alaw, GSM and ADPCM should only be used,
; the rest of the standard Asterisk codecs
; (speex, ilbc, lpc10, etc) should be avoided.
; The ulaw and alaw codecs have the best audio quality,
; followed by ADPCM, and lastly GSM,
; Bandwidth used is in the reverse order to audio quality.
; GSM uses the least bandwidth, and alaw/ulaw the most.
; CODEC AUDIO QUALITY BANDWIDTH (including IP and
Ethernet headers)
; ULAW best 87 kbps
; ADPCM good 55 kbps
; GSM mediocre 36 kbps
[general]
bindport = 4569 ; bindport and bindaddr may be specified
; NOTE: bindport must be specified BEFORE
; bindaddr or may be specified on a specific
; bindaddr if followed by colon and port
; (e.g. bindaddr=192.168.0.1:4569)
; bindaddr = 192.168.0.1 ; more than once to bind to multiple
; addresses, but the first will be the
; default
disallow = all ; The permitted codecs for outgoing connections
; Audio Quality Bandwidth
allow = ulaw ; best 87 kbps
allow = adpcm ; good 55 kbps
allow = gsm ; medicore 36 kbps
jitterbuffer = yes
forcejitterbuffer = yes
dropcount = 2
maxjitterbuffer = 4000
maxjitterinterps = 10
resyncthreshold = 1000
maxexcessbuffer = 80
minexcessbuffer = 10
jittershrinkrate = 1
tos = 0x1E
autokill = yes
delayreject = yes
; iaxthreadcount = 30
; iaxmaxthreadcount = 150
register = 29655:xxxxx at register.allstarlink.org ; This must be changed
to your node number, password
; remove the leading ";"
; Incoming radio connections
[radio]
type = user
disallow = all
allow = ulaw
allow = adpcm
allow = gsm
codecpriority = host
context = radio-secure
transfer = no
[iaxrpt] ; Connect from iaxrpt Username field
(PC AllStar Client)
type = user ; Notice type is user here <---------------
context = iaxrpt ; Context to jump to in extensions.conf
auth = md5
secret = Your_Secret_Pasword_Here
host = dynamic
disallow = all
allow = ulaw
allow = adpcm
allow = gsm
transfer = no
[iaxclient] ; Connect from iax client (Zoiper...)
type = friend ; Notice type here is friend <--------------
context = iax-client ; Context to jump to in extensions.conf
auth = md5
secret = Your_Secret_Password_Here
host = dynamic
disallow = all
allow = ulaw
allow = adpcm
allow = gsm
transfer = no
[allstar-sys]
type = user
context = allstar-sys
auth = rsa
inkeys = allstar
disallow = all
allow = ulaw
[allstar-public]
type = user
context = allstar-public
auth = md5
secret = allstar
disallow = all
allow = ulaw
allow = gsm
; The following should be un-commented to support Allstar Autopatch service
; [allstar-autopatch]
; type = peer
; host = register.allstarlink.org
; username = <One of the Node numbers on this server>
; secret = <The node password for the above node>
; auth = md5
; disallow = all
; allow = ulaw
; transfer = no
======================================
rpt.conf
---------
; Radio Repeater configuration file (for use with app_rpt)
; Your Repeater
[29655] ; Change this to your assigned node number
; Must also be enabled in modules.conf
; Rx audio/signalling channel. Choose ONLY 1 per node stanza
; Enable the selected channel driver in modules.conf !!!
; rxchannel = dahdi/pseudo ; No radio (hub)
; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel = Pi/1 ; Raspberry Pi PiTA
rxchannel = Radio/usb_29655 ; USBRadio (DSP)
; rxchannel = Dahdi/1 ; PCI Quad card
; rxchannel = Beagle/1 ; BeagleBoard
; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
duplex = 2 ; 0 = Half duplex with no
telemetry tones or hang time.
; Special Case: Full
duplex if linktolink is set to yes.
; This mode is preferred
when interfacing with an external multiport repeater controller.
; Comment out idrecording and idtalkover to suppress IDs also
; 1 = Half duplex with
telemetry tones and hang time. Does not repeat audio.
; This mode is preferred
when interfacing a simplex node.
; 2 = Full Duplex with
telemetry tones and hang time.
; This mode is preferred
when interfacing a repeater.
; 3 = Full Duplex with
telemetry tones and hang time, but no repeated audio.
; 4 = Full Duplex with
telemetry tones and hang time. Repeated audio only when the autopatch
is down.
linktolink = no ; disables forcing physical half-duplex operation of
main repeater while
; still keeping half-duplex semantics (optional)
linkmongain = 0 ; Link Monitor Gain adjusts the audio level of
monitored nodes when a signal from another node or the local receiver
is received.
; If linkmongain is set to a negative number the monitored audio will
decrease by the set amount in db.
; If linkmongain set to a positive number monitored audio will
increase by the set amount in db.
; The value of linkmongain is in db. The default value is 0 db.
erxgain = -3 ; Echolink receive gain adjustment
; Note: Gain is in db-volts (20logVI/VO)
etxgain = 3 ; Echolink transmit gain adjustment
; Note: Gain is in db-volts (20logVI/VO)
;eannmode = 1 ; 1 = Say only node number on
echolink connects (default = 1)
; 2 = say phonetic call sign
only on echolink connects
; 3 = say phonetic call sign
and node number on echolink connects
;controlstates = controlstates ; system control state stanza
scheduler = schedule ; scheduler stanza
functions = functions ; Repeater Function stanza
phone_functions = functions ; Phone Function stanza
link_functions = functions ; Link Function stanza
telemetry = telemetry ; Telemetry stanza
morse = morse ; Morse stanza
wait_times = wait-times ; Wait times stanza
context = radio ; dialing context for phone
callerid = "Repeater" <0000000000> ; callerid for phone calls
accountcode = RADIO ; account code (optional)
hangtime = 1000 ; squelch tail hang time (in ms) (optional, default 5
seconds, 5000 ms)
althangtime = 1000 ; longer squelch tail
totime = 300000 ; transmit time-out time (in ms) (optional, default 3
minutes 180000 ms)
idrecording = |iW5OMR/R ; id recording or morse string
see http://ohnosec.org/drupal/node/87
idtalkover = |iW5OMR ; Talkover ID (optional)
default is none see http://ohnosec.org/drupal/node/129
idtime = 540000 ; id interval time (in ms) (optional) Default 5
minutes (300000 ms)
politeid = 30000 ; time in milliseconds before ID timer expires to try
and ID in the tail. (optional, default 30000)
unlinkedct = ct2 ; Send a this courtesy tone when the user unkeys if
the node is not connected to any other nodes. (optional, default is
none)
remotect = ct3 ; remote linked courtesy tone (indicates a remote is in
the list of links)
linkunkeyct = ct8 ; sent when a transmission received over the link unkeys
;nolocallinkct = 0 ; Send unlinkedct instead if another local node is
connected to this node (hosted on the same PC).
;connpgm = yourconnectprogram ; Disabled. Execute a program you
specify on connect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being connected to us (them)
;discpgm = yourdisconnectprogram ; Disabled. Execute a program you
specify on disconnect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being disconnected from us (them)
;lnkactenable = 0 ; Set to 1 to enable the link activity timer.
Applicable to standard nodes only.
;lnkacttime = 1800 ; Link activity timer time in seconds.
;lnkactmacro = *52 ; Function to execute when link activity timer expires.
;lnkacttimerwarn = 30seconds ; Message to play when the link activity
timer has 30 seconds left.
;remote_inact_timeout = ; Specifies the amount of time without keying
from the link. Set to 0 to disable timeout. (15 * 60)
;remote_timeout = ; Session time out for remote base. Set to 0 to
disable. (60 * 60)
;remote_timeout_warning_freq = ; 30
;remote_timeout_warning = ; (3 * 60)
;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays.
holdofftelem = 1 ; Hold off all telemetry when signal is present on
receiver or from connected nodes
; except when an ID needs to be done and there is a signal coming from
a connected node.
telemdefault = 1 ; 0 = telemetry output off
; 1 = telemetry output on (default = 1)
; 2 = timed telemetry output
on command execution and for a short time thereafter.
telemdynamic = 1 ; 0 = disallow users to change
the local telemetry setting with a COP command,
; 1 = Allow users to change
the setting with a COP command. (default = 1)
;beaconing = 0 ; Send ID regardless of repeater activity (Required in
the UK, but probably illegal in the US)
parrotmode = 0 ; 0 = Parrot Off (default = 0)
; 1 = Parrot On Command
; 2 = Parrot Always
; 3 = Parrot Once by Command
parrottime = 1000 ; Set the amount of time in milliseconds
; to wait before parroting what was received
;rxnotch=1065,40 ; (Optional) Notch a
particular frequency for a specified
; b/w. app_rpt must have been
compiled with
; the notch option
startup_macro=*982 ; Macro to run at startup (optional)
nodenames = /var/lib/asterisk/sounds/rpt/nodenames ; Point to nodename
sound directory
; *** Status Reporting ***
; Uncomment either group following two statpost lines to report the
status of your node to stats.allstarlink.org
; depending on whether you are running ACID, Debian or Limey Linux.
; The difference is simply where your wget is located.
; ** For ACID and Debian ***
statpost_program =
/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
statpost_url = http://stats.allstarlink.org/uhandler.php ; Status updates
; ** For Limey Linux **
;statpost_program =
/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
;statpost_url = http://stats.allstarlink.org/uhandler.php ; Status updates
[functions]
; Prefix Functions
; *1 Disconnect Link
; *2 Monitor Link
; *3 Connect Link
; *4 Command Mode
; *5 Macros
; *6 User Functions
; *7 Connection Status/Functions
; *8 User Functions
; *9 User Functions
; *0 User Functions
; *A User Functions
; *B User Functions
; *C User Functions
; *D User Functions
; Mandatory Command Codes
; http://docs.allstarlink.org/drupal/node/91
1 = ilink,1 ; Disconnect specified link
2 = ilink,2 ; Connect specified link -- monitor only
3 = ilink,3 ; Connect specified link -- tranceive
4 = ilink,4 ; Enter command mode on specified link
70 = ilink,5 ; System status
99 = cop,6 ; PTT (phone mode only)
; End Mandatory Command Codes
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Macro Commands
5 = macro
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Autopatch Commands
; Note, This may be a good place for other 2 digit frequently used commands
61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up
62 = autopatchdn ;
Autopatch down
; autopatchup can optionally take comma delimited setting=value pairs:
; context = string ; Override default context with "string"
; dialtime = ms ; Specify the max number of milliseconds between phone
number digits (1000 milliseconds = 1 second)
; farenddisconnect = 1 ; Automatically disconnect when called party hangs up
; noct = 1 ; Don't send repeater courtesy tone during autopatch calls
; quiet = 1 ; Don't send dial tone, or connect messages. Do not send
patch down message when called party hangs up
; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Status Commands
; 1 - Force ID (global)
; 2 - Give Time of Day (global)
; 3 - Give software Version (global)
; 4 - Give GPS location info
; 5 - Last (dtmf) user
; 11 - Force ID (local only)
; 12 - Give Time of Day (local only)
721 = status,1 ; Force ID (global)
722 = status,2 ; Give Time of Day (global)
723 = status,3 ; Give software Version (global)
724 = status,4 ; Give GPS location info
725 = status,5 ; Last (dtmf) user
711 = status,11 ; Force ID (local only)
712 = status,12 ; Give Time of Day (local only)
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Link Commands
; 1 - Disconnect specified link
; 2 - Connect specified link -- monitor only
; 3 - Connect specified link -- tranceive
; 4 - Enter command mode on specified link
; 5 - System status
; 6 - Disconnect all links
; 7 - Last Node to Key Up
; 8 - Connect specified link -- local monitor only
; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.
; 10 - Disconnect all RANGER links (except permalinks)
; 11 - Disconnect a previously permanently connected link
; 12 - Permanently connect specified link -- monitor only
; 13 - Permanently connect specified link -- tranceive
; 15 - Full system status (all nodes)
; 16 - Reconnect links disconnected with "disconnect all links"
; 17 - MDC test (for diag purposes)
; 18 - Permanently Connect specified link -- local monitor only
; ilink commands 1 through 5 are defined in the Mandatory Command section
806 = ilink,6 ; Disconnect all links
807 = ilink,7 ; Last Node to Key Up
808 = ilink,8 ; Connect specified link -- local monitor only
809 = ilink,9,1999,"Testing" ; would send a text message to node 1999
replace 1999 with 0 for all connected nodes
; *** I'll change this later - just
noticed it ge/omr ***
810 = ilink,10 ; Disconnect all RANGER links (except permalinks)
811 = ilink,11 ; Disconnect a previously permanently connected link
812 = ilink,12 ; Permanently connect specified link -- monitor only
813 = ilink,13 ; Permanently connect specified link -- tranceive
815 = ilink,15 ; Full system status (all nodes)
816 = ilink,16 ; Reconnect links disconnected with
"disconnect all links"
817 = ilink,17 ; MDC test (for diag purposes)
818 = ilink 18 ; Permanently Connect specified link -- local
monitor only
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Control operator (cop) functions. Change these to something other
than these codes listed below!
901 = cop,1 ; System warm boot
902 = cop,2 ; System enable
903 = cop,3 ; System disable
904 = cop,4 ; Test tone on/off (toggle)
905 = cop,5 ; Dump system variables on console (debug use only)
907 = cop,7 ; Time out timer enable
908 = cop,8 ; Time out timer disable
909 = cop,9 ; Autopatch enable
910 = cop,10 ; Autopatch disable
911 = cop,11 ; User linking functions enable
912 = cop,12 ; User linking functions disable
913 = cop,13 ; Query system control state
914 = cop,14 ; Set system control state
915 = cop,15 ; Scheduler enable
916 = cop,16 ; Scheduler disable
917 = cop,17 ; User functions enable (time, id, etc)
918 = cop,18 ; User functions disable
919 = cop,19 ; Select alternate hang time (althangtime)
920 = cop,20 ; Select standard hangtime (hangtime)
921 = cop,21 ; Enable Parrot Mode
922 = cop,22 ; Disable Parrot Mode
923 = cop,23 ; Birdbath (Current Parrot Cleanup/Flush)
924 = cop,24 ; Flush all telemetry
925 = cop,25 ; Query last node un-keyed
926 = cop,26 ; Query all nodes keyed/unkeyed
930 = cop,30 ; Recall Memory Setting in Attached Xcvr
931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr
932 = cop,32 ; Touchtone pad test: command + Digit string + # to
playback all digits pressed
933 = cop,33 ; Local Telemetry Output Enable
934 = cop,34 ; Local Telemetry Output Disable
935 = cop,35 ; Local Telemetry Output on Demand
936 = cop,36 ; Foreign Link Local Output Path Enable
937 = cop,37 ; Foreign Link Local Output Path Disable
938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry
939 = cop,39 ; Foreign Link Local Output Path on Demand
942 = cop,42 ; Echolink announce node # only
943 = cop,43 ; Echolink announce node Callsign only
944 = cop,44 ; Echolink announce node # & Callsign
945 = cop,45 ; Link Activity timer enable
945 = cop,46 ; Link Activity timer disable
947 = cop,47 ; Reset "Link Config Changed" Flag
948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis)
949 = cop,49 ; Disable incoming connections (control state noice)
950 = cop,50 ; Enable incoming connections (control state noicd)
951 = cop,51 ; Enable sleep mode
952 = cop,52 ; Disable sleep mode
953 = cop,53 ; Wake up from sleep
954 = cop,54 ; Go to sleep
955 = cop,55 ; Parrot Once if parrot mode is disabled
956 = cop,56 ; Rx CTCSS Enable
957 = cop,57 ; Rx CTCSS Disable
958 = cop.58 ; Tx CTCSS On Input only Enable
959 = cop,59 ; Tx CTCSS On Input only Disable
960 = cop,60 ; Send MDC-1200 Burst
(cop,60,type,UnitID[,DestID,SubCode])
; Type is 'I' for PttID, 'E'
for Emergency, and 'C' for Call
; (SelCall or Alert), or 'SX'
for STS (ststus), where X is 0-F.
; DestID and subcode are only
specified for the 'C' type message.
; UnitID is the local systems
UnitID. DestID is the MDC1200 ID of
; the radio being called, and
the subcodes are as follows:
; Subcode '8205' is Voice
Selective Call for Spectra ('Call')
; Subcode '8015' is Voice
Selective Call for Maxtrac ('SC') or
; Astro-Saber('Call')
; Subcode '810D' is Call Alert
(like Maxtrac 'CA')
961 = cop,61 ; Send Message to USB to
control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
962 = cop,62 ; Send Message to USB to
control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)
963 = cop,63 ; Send pre-configred APRSTT
notification (cop,63,CALL[,OVERLAYCHR])
964 = cop,64 ; Send pre-configred APRSTT
notification, quietly (cop,64,CALL[,OVERLAYCHR])
965 = cop,65 ; Send POCSAG page (equipped
channel types only)
982 = playback,rpt/node_enabled ; Report node enabled to transmitter
[functions-remote]
0 = remote,1 ; Retrieve Memory
1 = remote,2 ; Set freq.
2 = remote,3 ; Set tx PL tone
3 = remote,4 ; Set rx PL tone
40 = remote,100 ; Rx PL off
41 = remote,101 ; Rx PL on
42 = remote,102 ; Tx PL off
43 = remote,103 ; Tx PL on
44 = remote,104 ; Low Power
45 = remote,105 ; Medium Power
46 = remote,106 ; High Power
711 = remote,107 ; Bump -20
714 = remote,108 ; Bump -100
717 = remote,109 ; Bump -500
713 = remote,110 ; Bump +20
716 = remote,111 ; Bump +100
719 = remote,112 ; Bump +500
721 = remote,113 ; Scan - slow
724 = remote,114 ; Scan - quick
727 = remote,115 ; Scan - fast
723 = remote,116 ; Scan + slow
726 = remote,117 ; Scan + quick
729 = remote,118 ; Scan + fast
79 = remote,119 ; Tune
51 = remote,5 ; Long status query
52 = remote,140 ; Short status query
67 = remote,210 ; Send a *
69 = remote,211 ; Send a #
;91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login.
; Define a different dtmf
sequence for each user which is
; authorized to use the remote
base to control access to it.
; For examble
9139583=remote,99,WB6NIL,G would grant access to
; the remote base and announce
WB6NIL as being logged in.
; Another entry,
9148351=remote,99,WA6ZFT,E would grant access to
; the remote base and announce
WA6ZFT as being logged in.
; When the remote base is
disconnected from the originating node, the
; user will be logged out. The
LICENSETAG argument is used to enforce
; tx frequency limits. See [txlimits] below.
85 = cop,6 ; Remote base telephone key
[telemetry]
; Telemetry entries can be shared across all repeaters, or defined for
each repeater.
; Can be a tone sequence, morse string, or a file
;
; |t - Tone escape sequence
;
; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2,
duration, amplitude)
; Single frequencies are created by setting freq1 or freq2 to zero.
;
; |m - Morse escape sequence
;
; Sends Morse code at the telemetry amplitude and telemetry frequency
as defined in the
; [morse] section.
;
; Follow with an alphanumeric string
;
; |i - Morse ID escape sequence
;
; Sends Morse code at the ID amplitude and ID frequency as defined in the
; [morse] section.
;
ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2 = |t(660,880,150,2048)
ct3 = |t(440,0,150,4096)
ct4 = |t(550,0,150,2048)
ct5 = |t(660,0,150,2048)
ct6 = |t(880,0,150,2048)
ct7 = |t(660,440,150,2048)
ct8 = |t(700,1100,150,2048)
ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)
remotemon = |t(1209,0,50,2048) ;
local courtesy tone when receive only
remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local
courtesy tone when linked Trancieve mode
cmdmode = |t(900,903,200,2048)
functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)
pfxtone = |t(350,440,30000,3072)
patchup = rpt/callproceeding
patchdown = rpt/callterminated
; As far as what the numbers mean,
; (000,000,010,000)
; | | | |-------amplitude
; | | |-------------duration
; | |-------------------Tone 2
; |-------------------------Tone 1
; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.
; Use it for a delay. Fine tuning for how long before telemetry is
sent, in conjunction with the telemdelay parameter)
; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay,
amplitude of 2048.
; Morse code parameters, these are common to all repeaters.
[morse]
speed = 20 ; Approximate speed in WPM
frequency = 800 ; Morse Telemetry Frequency
amplitude = 4096 ; Morse Telemetry Amplitude
idfrequency = 1065 ; Morse ID Frequency
idamplitude = 1024 ; Morse ID Amplitude
;
; This section allows wait times for telemetry events to be adjusted
; A section for wait times can be defined for every repeater
;
[wait-times]
telemwait = 1000 ; Time to wait before sending
most telemetry
idwait = 500 ; Time to wait before starting ID
unkeywait = 500 ; Time to wait after unkey
before sending CT's and link telemetry
calltermwait = 500 ; Time to wait before
announcing "call terminated"
;
; This is where you define your nodes which cam be connected to.
;
[nodes]
; Note, if you are using automatic update for allstar link nodes,
; no allstar link nodes should be defined here. Only place a definition
; for your local nodes, and private (off of allstar link) nodes here.
29655 = radio at 127.0.0.1:4569/29655,NONE ; This must be changed to your
node number
; and iax port number if not the default
; Memories for remote bases
[memory]
;00 = 146.580,100.0,m
;01 = 147.030,103.5,m+t
;02 = 147.240,103.5,m+t
;03 = 147.765,79.7,m-t
;04 = 146.460,100.0,m
;05 = 146.550,100.0,m
; Place command macros here
[macro]
;1 = *32011#
;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#
;3 = *32001*32011*32050*32030*32060#
; Data Acquisition configuration
;[daq-list]
;device = device_name1
;device = device_name2
;Where: device_name1 and device_name2 are stanzas you define in this file
;device = daq-cham-1
; Device name
;[daq-cham-1] ; Defined in [daq-list]
;hwtype = uchameleon ; DAQ hardware type
;devnode = /dev/ttyUSB0 ; DAQ device node (if required)
;1 = inadc ; Pin definition for an ADC channel
;2 = inadc
;3 = inadc
;4 = inadc
;5 = inadc
;6 = inadc
;7 = inadc
;8 = inadc
;9 = inp ; Pin definition for an input with a weak pullup resistor
;10 = inp
;11 = inp
;12 = inp
;13 = in ; Pin definition for an input without a weak pullup resistor
;14 = out ; Pin definition for an output
;15 = out
;16 = out
;17 = out
;18 = out
;[meter-faces]
;face = scale(scalepre,scalediv,scalepost),word/?,...
;
; scalepre = offset to add before dividing with scalediv
; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for
20 volts).
; scalepost = offset to add after dividing with scalediv
;
;face = range(X-Y:word,X2-Y2:word,...),word/?,...
;face = bit(low-word,high-word),word/?,...
;
; word/? is either a word in /var/lib/asterisk/sounds or one of its
subdirectories,
; or a question mark which is a placeholder for the measured value.
;
;
; Battery voltage 0-20 volts
;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts
; 4 quadrant wind direction
;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?
; LM34 temperature sensor with 130 deg. F full scale
;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit
; Status poll (non alarmed)
;light = bit(ha/off,ha/on),ha/light,?
;[alarms]
;
;tag = device,pin,node,ignorefirst,func-low,func-hi
;
;tag = a unique name for the alarm
;device = daq device to poll
;pin = the device pin to be monitored
;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it
;node = the node number to execute the function on
;func-low = the DTMF function to execute on a high to low transition
;func-high = the DTMF function to execute on a low to high transition
;
; a '-' as a function name is shorthand for no-operation
;
;door = daq-cham-1,9,1,2017,*7,-
;pwrfail = daq-cham-1,10,0,2017,*911111,-
;
; Control states
; Allow several control operator functions to be changed at once using
one command (good for scheduling)
;
;[controlstates]
;statenum = copcmd,[copcmd]...
;0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation
;1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation
;2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation
; Scheduler - execute a macro at a given time
[schedule]
;dtmf_function = m h dom mon dow ; ala cron, star is implied
;2 = 00 00 * * * ; at midnight, execute macro 2.
==============================================
echolink.conf (not that I think -this- part matters much)
[el0]
call = W5OMR/R ; Change this!
pwd = xxxxx ; Change this!
name = Geoff ; Change this!
qth = Splendora ; Change this!
email = INVALID ; Change this!
node = 004817 ; Change this!
; Data for EchoLink Status Page
lat = 0.0 ; Latitude in decimal degrees
lon = 0.0 ; Longitude in decimal degrees
freq = 0.0 ; not mandatory Frequency in MHz
tone = 0.0 ; not mandatory CTCSS Tone (0 for none)
power = 5 ; 0=0W, 1=1W, 2=4W, 3=9W, 4=16W, 5=25W, 6=36W, 7=49W, 8=64W,
9=81W (Power in Watts)
height = 2 ; 0=10 1=20 2=40 3=80 4=160 5=320 6=640 7=1280 8=2560
9=5120 (AMSL in Feet)
gain = 9 ; Gain in db (0-9)
dir = 0 ; 0=omni 1=45deg 2=90deg 3=135deg 4=180deg 5=225deg 6=270deg
7=315deg 8=360deg (Direction)
maxstns = 5 ; Max Stations
rtcptimeout = 10
recfile = /tmp/echolink_recorded.gsm ;
astnode = 29655 ; Change this!
context = radio-secure ; Default in code is echolink-in
; Max 3 servers
server1 = nasouth.echolink.org
server2 = naeast.echolink.org
server3 = server3.echolink.org
; To deny w6xxx you would add the statement: deny = w6xxx
; To prohibit computer-based connections you would write: permit = *-*
; To allow access to only a select group of callsigns: permit = w6abc,w6def,...
; permit ; comma delimited list of callsign, type (-r)
; deny
; Remote text commands thru netcat:
; o.conip <IPaddress> (request a connect)
; o.dconip <IPaddress> (request a disconnect)
; o.rec (turn on/off recording)
; ipaddr
; port
===============================
So, does anything 'jump out' at ya?
--
73 = Best Regards,
-Geoff/W5OMR
More information about the App_rpt-users
mailing list