[App_rpt-users] URI GPIO

[David McGough]

Probably not (lets hope!)....It's worthwhile to test the URI GPIO pins 
with a voltmeter/multimeter before proceeding! Check the voltage to 
ground, and flip the logic bit back and forth a few times in software.

73, David KB4FXC


On Mon, 4 Jun 2018, Scott Weis wrote:

> Hopefully I didn't blow anything up...

-----Original Message-----
From: App_rpt-users [mailto:app_rpt-users-bounces at lists.allstarlink.org] On Behalf Of David McGough
Sent: Monday, June 4, 2018 12:05 AM
To: Users of Asterisk app_rpt <app_rpt-users at lists.allstarlink.org>
Subject: Re: [App_rpt-users] URI GPIO


Scott,

The URI GPIO pins are connected to the DB-25 without any buffering, etc. 
They are 3.3V logic, but based on the datasheet are considered to be 5V tolerant.

You'll most likely need a level converter on each GPIO pin used to drive a
CDM1250 pin. A simple open-collector or open-drain transistor buffer on each used GPIO pin will work nicely.

There are dozens of acceptable ways to accomplish the buffering. Here is one sample schematic using an NPN bipolar transistor and includes LED's for visual feedback. Note that this circuit inverts the logic, so logic 0 becomes 1 and vice-versa.

https://hamvoip.org/docs/ptt-driver-example.png


73, David KB4FXC



On Sun, 3 Jun 2018, Scott Weis wrote:

> Isn’t the URI 5v logic?
> 
>  
> 
> From: App_rpt-users 
> [mailto:app_rpt-users-bounces at lists.allstarlink.org] On Behalf Of 
> Bryan Fields
> Sent: Sunday, June 3, 2018 7:06 PM
> To: Users of Asterisk app_rpt <app_rpt-users at lists.allstarlink.org>
> Subject: Re: [App_rpt-users] URI GPIO
> 
>  
> 
> Do you have a buffer from the 3.3v to 5v logic?
> 
> --
> 
> Bryan Fields
> 
> M: +1-727-409-1194
> 
> 
> On Jun 3, 2018, at 18:27, Scott Weis <kb2ear at kb2ear.net <mailto:kb2ear at kb2ear.net> > wrote:
> 
> I'm trying to set up channel steering for a Motorola CDM1250 and have 
> the radio working without a URI. If I ground the channel pins the 
> channels change on the radio fine.  Now when I connect the pins to a 
> URI-x gpio1
> gpio2 gpio5 and gpio6 It dosent seem to work. I have gpio1=out0 , 
> gpio2=out0, gpio5=out0, gpio6=out0 and when I do a *584=cop,61,GPIO5=1 
> or
> *585=cop,61,GPIO5=0  nothing seems to change on the URI, either state 
> I see
> +5v on the URI. Should it not get pulled to ground?
> 
> Am I doing something wrong?
> 
> Thanks & 73
> de Scott KB2EAR
> 
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org 
> <mailto:App_rpt-users at lists.allstarlink.org>
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
> 
> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. 
> 
> 

_______________________________________________
App_rpt-users mailing list
App_rpt-users at lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. 

_______________________________________________
App_rpt-users mailing list
App_rpt-users at lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.