<HTML><HEAD></HEAD>
<BODY dir=ltr>
<DIV dir=ltr>
<DIV style="FONT-FAMILY: 'Calibri'; COLOR: #000000; FONT-SIZE: 12pt"><FONT
face="Times New Roman">As I am reading this thread about the RC210 and the
software a question come <BR>to mind..<BR><BR>Is a controler mandatory to use
the app_rpt software?? your getting me
<BR>confuse..<BR><BR><BR><BR>-----Original Message----- <BR>From: Doug
Hutchison<BR>Sent: Friday, May 27, 2011 5:13 PM<BR>To: </FONT><A
href="mailto:App_rpt-users@ohnosec.org"><FONT
face="Times New Roman">App_rpt-users@ohnosec.org</FONT></A><BR><FONT
face="Times New Roman">Subject: Re: [App_rpt-users] Allstar Node and RC210
Issues<BR><BR>Have you adjusted the TX audio pot on the 210? Port 2 must be
simplex<BR>(non repeat) as Matt said.<BR><BR>D<BR><BR><BR><BR>On 27/05/2011
21:59:34, Charles Rader (</FONT><A href="mailto:kc5dgc@centurytel.net"><FONT
face="Times New Roman">kc5dgc@centurytel.net</FONT></A><FONT
face="Times New Roman">) wrote:<BR>> Monty,<BR>><BR>> Thank you. The
conf file you sent me was a big help. I wished mine<BR>conf files was commented
like the one you had. That explains a lot. I<BR>made the changes you said to
make in the rpt.conf. It helped increase my<BR>audio and it sounds much better
for some reason now. I am still having<BR>issues with the link UHF repeater
though.<BR>> Here is my setup:<BR>> RC210 Port 1 UHF Repeater, Port 2 URI
(allstar)<BR>><BR>> URI to RC210 Port2<BR>> Pin 1 (PTT) to Pin 7 (RX
COS)<BR>> Pin 8 (COR DET) to Pin 3 (TX PTT)<BR>> Pin 13 (GND) to Pin 9
(GND)<BR>> Pin 21 (MIC IN AC) to Pin 4 (TX AUDIO)<BR>> Pin 22 (LEFT OUT
AC) to Pin 5 (AUDIO INPUT)<BR>><BR>> RC210 Port 1 and Port 2
Linked<BR>> Port 2 setup- Hang Timer=0; Transmitter Enabled; Receiver
Enabled;<BR>Repeater Mode; DTMF Enabled; Monitor Mix; Access Mode=
Carrier<BR>><BR>> I can Link my Allstar node to an active Allstar Mode and
I have great<BR>audio repeater on the UHF Repeater. But when I key up to
transmit on my<BR>UHF repeater I am getting PTT Lights on Port 2 on the
controller but I<BR>am not getting a keyup or audio on the Allstar node either
locally (via<BR>iaXrpt) or through Webtransciever. Also I can’t connect or send
any<BR>commands via the UHF port to Allstar.<BR>><BR>> Any ideas? I was
told that I shouldn’t program port 2 on the RC210 as<BR>Repeater
mode?<BR>><BR>> Thanks for all your time and help.<BR>><BR>> From:
Monty<BR>> Sent: Friday, May 27, 2011 2:12 PM<BR>> To: Charles
Rader<BR>> Subject: Re: [App_rpt-users] Allstar Node and RC210
Issues<BR>><BR>> Hi Charles,<BR>> I have interfaced Allstar to my
RC-210. I had a couple of problems.<BR>One was my wiring, everything is
backwards. PTT on the arcom goes to COR<BR>on URI, Audio out to audio in, etc.
So i would check that.. Also if you<BR>haven't done any config on your allstar
node, that might
be<BR>_______________________________________________<BR>App_rpt-users mailing
list<BR></FONT><A href="mailto:App_rpt-users@ohnosec.org"><FONT
face="Times New Roman">App_rpt-users@ohnosec.org</FONT></A><BR><A
href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users"><FONT
face="Times New Roman">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</FONT></A><FONT
face="Times New Roman"> </FONT><BR></DIV></DIV></BODY></HTML>