<html>
<head>
<meta content="text/html; charset=ISO-8859-1"
http-equiv="Content-Type">
</head>
<body bgcolor="#FFFFFF" text="#000000">
Hi Chris, In the usbradio.conf make sure you have
ctcssfrom=usbinvert if your tone decode is active low and uncomment
the ctcss settings as below.<br>
Change the tone as required for your setup. Restart asterisk. and it
should now require both the cor and ctcss to active the repeater
function.<br>
<br>
Jon VA3RQ<br>
<br>
<br>
<blockquote type="cite">[general]<br>
<br>
[usb1234]<br>
<br>
hdwtype=0 ; Leave this set to 0 for USB sound fobs
modified using<br>
; the instructions from usbfob.pdf. Use a setting
of <br>
; 1 is for Dingotel/Sph interfaces.<br>
<br>
rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db
attenuator removed<br>
; Set to 1 for additonal gain if using a low-level
receiver output<br>
txboost=0 ;<br>
<br>
rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx
HPF<br>
; Do not change this, leave this as a 1<br>
<br>
txctcssdefault=103.5 ; default tx ctcss freq, any frequency
permitted<br>
rxctcssfreqs=103.5 ; rx ctcss freqs in floating point. must
be in table<br>
txctcssfreqs=103.5 ; tx ctcss freqs, any frequency
permitted<br>
;rxctcssoverride=0 ; Set to 1 or yes to start out in
carrier squelch mode<br>
<br>
carrierfrom=usbinvert ; no,usb,usbinvert,dsp,vox <br>
; no - no carrier detection at all<br>
; usb - from the COR line on the modified USB
sound fob<br>
; usbinvert - from the inverted COR line on the
modified USB sound fob<br>
; dsp - from RX noise using dsp techniques<br>
; vox - voice activated from RX audio<br>
<br>
ctcssfrom=usbinvert ; no,usb,usbinvert,dsp<br>
; no - CTCSS decoding, system will be carrier
squelch<br>
; usb - CTCSS decoding using input from USB FOB
-active HI<br>
; usbinvert -CTCSS decoding using input from USB
FOB -active LO<br>
; dsp - CTCSS decoding using RX audio in DSP.<br>
; rxdemod option must be set to flat for this to
work.</blockquote>
<br>
<br>
On 12/31/2012 8:55 PM, Chris K7AZ wrote:
<blockquote cite="mid:CD07822C.15AF6%25kilo7AlphaZulu@verizon.net"
type="cite">
<title>URIx Now Repeating Fine But Only Carrier Squelch Mode</title>
<font face="Arial"><span style="font-size:14.0px">First a big
thank you to those that helped get my URIx module to key the
repeater transmitter and allow audio to pass through.<br>
Meanwhile... somewhere it has lost the CTCSS (PL) input
requirement or in other words, it is now a carrier squelch
repeater. <br>
Is there a setting to re-enable the CTCSS (PL) logic?
Manually grounding the CTCSS input does not key the system
but grounding the COS input does blow squelch noise through
just fine. <br>
<br>
Chris K7AZ<br>
<br>
<br>
<br>
<br>
</span></font>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<br>
<pre wrap="">_______________________________________________
App_rpt-users mailing list
<a class="moz-txt-link-abbreviated" href="mailto:App_rpt-users@ohnosec.org">App_rpt-users@ohnosec.org</a>
<a class="moz-txt-link-freetext" href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a>
</pre>
</blockquote>
</body>
</html>