<p>I have the same issue.  First with a home brew interface so I searched hi and low for the "actual" interface board with the same issue as Kirk describes.</p>
<p>De k0jsc</p>
<div class="gmail_quote">On Jun 11, 2013 9:41 PM, "Monty" <<a href="mailto:monty@ke7jvx.com">monty@ke7jvx.com</a>> wrote:<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Hi Kyle,<div><br></div><div>I fixed the syntax error, still no joy.  I did have a usbradio node and the 707 on simpleusb, so I migrated the 707 to usbradio and removed all the simpleusb configs, still no joy.  Any other ideas?<br clear="all">


<div><br>Monty</div>
<br><br><div class="gmail_quote">On Tue, Jun 11, 2013 at 6:42 PM, K&R Yoksh <span dir="ltr"><<a href="mailto:yokshs@gmail.com" target="_blank">yokshs@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">


Hello Monty,<br>
While not specific to the remote operation, I see one thing that might make app_rpt lose it's mind.<br>
<br>
The rxchannel parameter is very picky about syntax, especially the upper and lower case letters. The correct format is:<br>
<br>
rxchannel=SimpleUSB/usb1010<br>
<br>
Another thing I've learned is to never (NEVER) have usbradio.conf and simpleusb.conf exist in /etc/asterisk at the same time. This will<br>
confuse app_rpt at the least, or crash it altogether.<br>
<br>
73,<br>
<br>
Kyle Yoksh<br>
K0KN<br>
Olathe, KS<br>
Allstar 2210-2219<br>
--- Original Message ---Hello Everyone,<div><div><br>
<br>
I have tried two Kenwood G707s with three of Jim's URI Adapter cards and<br>
two URIs on two different computers.  I am able to get three or four<br>
commands (freq, pl tone, etc) then I will get Allison saying "Invalid<br>
Frequency" and the CLI shows:<br>
<br>
"WARNING[7925]: app_rpt.c:13876 serial_remote_io: -99999 Serial device not<br>
responding on node 1010"<br>
<br>
The radio will not steer or accept commands anymore until I power cycle the<br>
707.  The after power cycle three or four commands and will not steer<br>
again.  I have tried the same computer with a VHF Syntor with an xcat and<br>
will accept every command without issue.  Also one of my 707s now lives on<br>
a Quad PCI card and steers with every command without issue.  Has anyone<br>
else seen this or know the remedy?  Below is my rpt.conf with the URI:<br>
<br>
[1010]<br>
archivedir=/etc/asterisk/qso<br>
rxchannel = simpleusb/usb1010<br>
duplex=0<br>
ioport = /dev/ttyS0<br>
remote = kenwood<br>
authlevel = 1<br>
memory=memory<br>
remote_inact_timeout=5400<br>
remote_timeout=5400<br>
functions=remote-functions<br>
phone_functions=remote-<u></u>functions<br>
link_functions=remote-<u></u>functions <br></div></div><div><div>
______________________________<u></u>_________________<br>
App_rpt-users mailing list<br>
<a href="mailto:App_rpt-users@ohnosec.org" target="_blank">App_rpt-users@ohnosec.org</a><br>
<a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/<u></u>mailman/listinfo/app_rpt-users</a><br>
</div></div></blockquote></div><br></div>
<br>_______________________________________________<br>
App_rpt-users mailing list<br>
<a href="mailto:App_rpt-users@ohnosec.org">App_rpt-users@ohnosec.org</a><br>
<a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a><br>
<br></blockquote></div>