<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 TRANSITIONAL//EN">
<HTML>
<HEAD>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; CHARSET=UTF-8">
<META NAME="GENERATOR" CONTENT="GtkHTML/4.4.4">
</HEAD>
<BODY>
Sorry, didn't notice that was off list.....<BR>
Copied below.<BR>
<TABLE CELLSPACING="0" CELLPADDING="0" WIDTH="100%">
<TR>
<TD>
-- <BR>
<I>Robert A. Poff</I><BR>
<I>Loganville, PA</I><BR>
<BR>
<B><I><A HREF="http://wb3awj.hobby-site.org/loon.htm">S/V Loon</A></I></B><BR>
<I><FONT SIZE="2">1983 Hunter 34</FONT></I><BR>
<I><FONT SIZE="2">Havre de Grace, MD.</FONT></I><BR>
<BR>
WB3AWJ<I> - Allstar 27784</I><BR>
<I>Powered by Linux</I> <BR>
<BR>
</TD>
</TR>
</TABLE>
-------- Forwarded Message --------<BR>
<B>From</B>: Tim Sawyer <<A HREF="mailto:Tim%20Sawyer%20%3ctim.sawyer@me.com%3e">tim.sawyer@me.com</A>><BR>
<B>To</B>: Robert A. Poff WB3AWJ <<A HREF="mailto:%22Robert%20A.%20Poff%20WB3AWJ%22%20%3cwb3awj@comcast.net%3e">wb3awj@comcast.net</A>><BR>
<B>Subject</B>: Re: [App_rpt-users] Frequency Agile Remote - Continued<BR>
<B>Date</B>: Fri, 26 Jul 2013 22:31:53 -0700<BR>
<BR>
Here's my Xcat config... if it helps any.
<BR>
<BR>
<BR>
<BR>
<BR>
<BR>
[2535] ; Change this to your assigned node number
<BR>
<BR>
rxchannel = Simpleusb/usb ; Rx audio/signalling channel
remote = xcat
civaddr = 32
functions = functions-remote
lconn = PP3=1
ldisc = PP3=0
memory = memory ; Section to hold memory entries (optional)
; remote=ft897 for Yaesu FT-897 or
; remote=rbi for Doug Hall RBI1
; remote=kenwood for Kenwood mobiles such as the TMG707A
; remote=ic706 for the Icom IC-706
ioport = /dev/ttyS0 ; Specify port for serial port (optional)
iospeed = 19200
dusbabek = yes
<BR>
<BR>
;iobase = 0x378 ; Specify IO port for parallel port (optional)
authlevel = 2 ; Remote base authentication level
;; authlevel = 0 : Anyone can use it
;; authlevel = 1 : Requires log in, Waits for Tx key to ask for it
;; authlevel = 2 : Requires log in, asks for it automously
;mars = 0 ; set=1 for IC-706 w/MARS mods (optional)
<BR>
<BR>
remote_inact_timeout=1800 ; Inactivity timer for remote base nodes only (set to 0 to disable).
remote_timeout=5400 ; Session time out for remote base. (set to 0 to disable)
;remote_timeout=120 ; Session time out for remote base. (set to 0 to disable)
;remote_timeout_warning=30
<BR>
<BR>
--<BR>
Tim<BR>
:wq
<BR>
On Jul 26, 2013, at 9:21 PM, Robert A. Poff WB3AWJ <<A HREF="mailto:wb3awj@comcast.net">wb3awj@comcast.net</A>> wrote:
<BR>
<BLOCKQUOTE TYPE=CITE>
Still can't set the frequency on an XCAT.<BR>
<BR>
I've done a complete clean install.<BR>
<BR>
By running Asterisk in the foreground and turning up the debug levels, I see the CIV command being <BR>
sent to the XCAT is
<PRE>
FE FE 20 E0 08 01 FD
</PRE>
Which if I'm right is trying to retrieve memory #1 from the radio. Not write to the VFO (function 05 instead of 08). <BR>
In rpt.conf I have the remote defined as xcat (remote = xcat).<BR>
<BR>
So what gives?<BR>
<BR>
Again, this was working before I updated from a version of app_rpt from about a year ago, to current.<BR>
<BR>
</BLOCKQUOTE>
<BLOCKQUOTE TYPE=CITE>
</BLOCKQUOTE>
<BLOCKQUOTE TYPE=CITE>
Robert A. Poff<BR>
Loganville, PA.<BR>
<BR>
<BR>
"Lieutenant, target the offending power boat and launch photon torpedoes"
</BLOCKQUOTE>
<BLOCKQUOTE TYPE=CITE>
<BR>
<BR>
</BLOCKQUOTE>
<BLOCKQUOTE TYPE=CITE>
_______________________________________________<BR>
App_rpt-users mailing list<BR>
<A HREF="mailto:App_rpt-users@ohnosec.org">App_rpt-users@ohnosec.org</A><BR>
<A HREF="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</A><BR>
<BR>
</BLOCKQUOTE>
<BR>
</BODY>
</HTML>