<div dir="ltr"><div><div><div><div>I use FT8900 with rear packet minidim with URI DMK <br></div>so I will change<br></div>ctssfrom=no/usb <br></div>carrierfrom=usb or usbinvert/dsp( I think the yaesu use cor low but anyway the uri work nice with ptt and audio from internet the problem is only the audio from my rig to internet is deaf)<br>
</div>rxdemod=flat/no<br><div><br></div></div><div class="gmail_extra"><br><br><div class="gmail_quote">2014-02-08 22:43 GMT+00:00 REDBUTTON_CTRL <span dir="ltr"><<a href="mailto:jrorke@cogeco.ca" target="_blank">jrorke@cogeco.ca</a>></span>:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div bgcolor="#FFFFFF" text="#000000">
Oh and set ctcssfrom=no<br>
That way it wont be looking for a tone decoder output to let audio
in.<br>
Jon RQ<div><div class="h5"><br>
<br>
On 2/8/2014 5:39 PM, REDBUTTON_CTRL wrote:
<blockquote type="cite">
If this is your usb radio.conf file then it is missing a couple of
things.<br>
<br>
You need the following:<br>
<br>
carrierfrom=usb (or usbinvert if your cor is active low)<br>
<br>
and the rxdemod must be set to speaker or flat<br>
<br>
That should get tit listening to rx audio to start.<br>
<br>
Jon VA3RQ<br>
<br>
On 2/8/2014 5:31 PM, ea8ee wrote:
<blockquote type="cite">
<div dir="ltr">
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>usb27305<br>
</div>
rxboost=1<br>
</div>
txboost=1<br>
</div>
rxctcssrelax=1<br>
</div>
txctcssdefault=88.5<br>
</div>
rxctcssfreqs=88.5<br>
</div>
;rxctcssoverride=0<br>
</div>
ctcssfrom=usb<br>
</div>
rxdemod=no<br>
</div>
txprelim=no<br>
</div>
txlimonly=no<br>
</div>
txtoctype=notone<br>
</div>
txmixa=composite<br>
</div>
txmixb=composite <br>
</div>
invertptt=0<br>
</div>
duplex=0<br>
</div>
rxondelay=o<br>
</div>
rxnoisefiltype=0<br>
</div>
eeprom=1<br>
<br>
The DMK works nice in TX but in RX not receive nothing<br>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div><br>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
<div class="gmail_extra"><br>
<br>
<div class="gmail_quote">2014-02-08 20:02 GMT+00:00 Doug
Crompton <span dir="ltr"><<a href="mailto:doug@crompton.com" target="_blank">doug@crompton.com</a>></span>:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div>
<div dir="ltr"><font face="Tahoma">I think it found your
adapter as you said you had audio in one direction.
If not see below.<br>
<br>
Did you select the active usb device in the config
utility before you tried to make changes?<br>
<br>
<br>
If the adapter is not being found at all try
this....<br>
<br>
The following USB interfaces are defined in usbradio
-<br>
<br>
#define C108_VENDOR_ID 0x0d8c<br>
#define C108_PRODUCT_ID 0x000c<br>
#define C108AH_PRODUCT_ID 0x013c<br>
#define C119_PRODUCT_ID 0x0008<br>
#define C119A_PRODUCT_ID 0x013a<br>
#define N1KDO_PRODUCT_ID 0x6a00<br>
#define C108_HID_INTERFACE 3<br>
<br>
When you boot up you should see one of these
initialized in the messages. After boot do -<br>
<br>
dmesg | more<br>
<br>
and page through and see if it found your adapter.<br>
<br>
I am using the DMK and it looks like this -<br>
<br>
[root@WA3DSP_Allstar wa3dsp]# dmesg | grep Sound<br>
input: C-Media Electronics Inc. USB PnP Sound
Device as /class/input/input0<br>
input,hidraw0: USB HID v1.00 Device [C-Media
Electronics Inc. USB PnP Sound Device] on
usb-0000:00:1d.0-1<br>
<br>
</font>
<div><b><font style="font-size:16pt" size="4">73
Doug</font><font style="font-size:16pt" size="4"><br>
</font><font style="font-size:16pt" size="4">WA3DSP</font><font style="font-size:16pt" size="4"><br>
</font><font style="font-size:16pt" size="4"><a href="http://www.crompton.com/hamradio" target="_blank">http://www.crompton.com/hamradio</a></font></b><font style="font-size:16pt" size="4"><br>
</font><br>
<br>
</div>
<div>
<hr>From: <a href="mailto:ea8ee1@gmail.com" target="_blank">ea8ee1@gmail.com</a><br>
Date: Sat, 8 Feb 2014 19:14:56 +0000<br>
To: <a href="mailto:app_rpt-users@ohnosec.org" target="_blank">app_rpt-users@ohnosec.org</a><br>
Subject: Re: [App_rpt-users] audio radio to internet
issue
<div>
<div><br>
<br>
<div dir="ltr">I tried with cli and radio tune
rxnoise and the pc says the device usb27305
currectly not active ! any suggestion?<br>
<div><br>
<br>
<div>2014-02-08 8:51 GMT+00:00 jose <span dir="ltr"><<a href="mailto:ea8ee1@gmail.com" target="_blank">ea8ee1@gmail.com</a>></span>:<br>
<blockquote style="border-left:1px solid rgb(204,204,204);padding-left:1ex">
<div>
<div>Hi Doug! the ptt and audio from
internet to radio works nicely the
problem is about the audio from
radio to internet not audio neither
the node receive the dmtf from radio
or webstransceiver<br>
<br>
El 08/02/2014 6:31, Doug Crompton
escribió:<br>
</div>
<div>
<blockquote><font face="Tahoma">You
need to set - <br>
<br>
duplex=1 ; Simplex, no
telelmetry<br>
duplex=0 ; Simplex, telelmetry<br>
<br>
in rpt.conf if you are running
simplex. <br>
<br>
Also make sure the polarity is
correct in your usbradio or
simpleusb file for the PTT and
COS if you are using it.<br>
</font></blockquote>
<br>
</div>
</div>
</blockquote>
</div>
<br>
</div>
</div>
<br>
</div>
</div>
<div>_______________________________________________
App_rpt-users
mailing list <a href="mailto:App_rpt-users@ohnosec.org" target="_blank">App_rpt-users@ohnosec.org</a> <a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a>
To unsubscribe from this list please visit <a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a>
and scroll down to the bottom of the page. Enter
your email address and press the "Unsubscribe or
edit options button" You do not need a password to
unsubscribe, you can do it via email confirmation.
If you have trouble unsubscribing, please send a
message to the list detailing the problem.</div>
</div>
</div>
</div>
</blockquote>
</div>
<br>
</div>
<br>
<fieldset></fieldset>
<br>
<pre>_______________________________________________
App_rpt-users mailing list
<a href="mailto:App_rpt-users@ohnosec.org" target="_blank">App_rpt-users@ohnosec.org</a>
<a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a>
To unsubscribe from this list please visit <a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. </pre>
</blockquote>
<br>
<fieldset></fieldset>
<br>
<pre>_______________________________________________
App_rpt-users mailing list
<a href="mailto:App_rpt-users@ohnosec.org" target="_blank">App_rpt-users@ohnosec.org</a>
<a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a>
To unsubscribe from this list please visit <a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
</pre>
</blockquote>
</div></div></div>
<br>_______________________________________________<br>
App_rpt-users mailing list<br>
<a href="mailto:App_rpt-users@ohnosec.org">App_rpt-users@ohnosec.org</a><br>
<a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a><br>
<br>
To unsubscribe from this list please visit <a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"<br>
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. <br></blockquote></div><br></div>