<div dir="ltr"><div>2  - VOTER Server Address (FQDN) (<a href="http://voter-demo.allstarlink.org">voter-demo.allstarlink.org</a>)</div><div>3  - VOTER Server Port (667),  4  - Local Port (Override) (0)</div><div>5  - Client Password (rptnopl),  6  - Host Password (rptnopl)</div>
<div>7  - Tx Buffer Length (3000)</div><div>8  - GPS Data Protocol (0=NMEA, 1=TSIP) (0)</div><div>9  - GPS Serial Polarity (0=Non-Inverted, 1=Inverted) (0)</div><div>10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (2)</div>
<div>11 - GPS Baud Rate (4800)</div><div>12 - External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted) (1)</div><div>13 - COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver) (1)</div><div>14 - Debug Level (9)</div><div>15  - Alt. VOTER Server Address (FQDN) ()</div>
<div>16  - Alt. VOTER Server Port (Override) (0)</div><div>17  - DSP/BEW Mode NOT SUPPORTED</div><div>18 - "Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs) (0)</div><div>19 - Simulcast Launch Delay (0) (approx 200 ns, 5 = 1us, > 0 to ENA SC)</div>
<div>97 - RX Level,  98 - Status,  99 - Save Values to EEPROM</div><div>i - IP Parameters menu, o - Offline Mode Parameters menu</div><div>q - Disconnect Remote Console Session, r - reboot system, d - diagnostics</div><div>
<br></div><div>Enter Selection (1-27,97-99,r,q,d) : <System Time Not Set>  Using Primary Voter Host (72.0.177.212)</div><div><System Time Not Set>  Voter Host DNS Resolved to 96.36.57.202</div><div><System Time Not Set>  Connection Using Voter Host (96.36.57.202)</div>
<div><System Time Not Set>  Using Primary Voter Host (96.36.57.202)</div><div><br></div><div><br></div><div><br></div><div><div>Select the following Diagnostic functions:</div><div><br></div><div>1  - Set Initial Tone Level (and assert PTT)</div>
<div>2  - Display Value of DIP Switches</div><div>3  - Flash LED's in sequence</div><div>4  - Run entire diag suite</div><div>c  - Show Diagnostic Cable Pinouts</div><div>x -  Exit Diagnostic Menu (back to main menu)</div>
<div>q - Disconnect Remote Console Session, r - reboot system</div><div><br></div><div>Enter Selection (1-4,c,x,q,r) : 4^M</div><div> </div><div>Running Diagnostics...</div><div><br></div><div>Testing PTT/External CTCSS</div>
<div>Error - Failed to read PTT/CTCSS in un-asserted state</div><div><b>Testing GPS UART</b></div><div><b>Error - Failed to read data from GPS UART</b></div><div>Testing level at 100 Hz for Normal Audio</div><div>^C</div>
<div><br></div><div><br></div><div>Select the following Diagnostic functions:</div></div><div><br></div><div><br></div><div>--- No the LED's do not come on for GPS/HST</div><div>rechecked the wiring all looks right </div>
<div>assuming GTX is transmit that goes to the GPS rx line and vice versa</div><div><br></div><div>GPPS pin 7 is labeled as PTT out in the documentation - not sure what that means, I thought it was Gps 1pps?</div><div><br>
</div><div><a href="http://206.212.254.21/unode_docs/rtcm_%20manual.pdf">http://206.212.254.21/unode_docs/rtcm_%20manual.pdf</a><br></div><div><br></div><div><div>P2 - DB15F D-Shell connector for the RS-232 (console @57600 bps, DCE) and GPS </div>
<div>1 - NC </div><div>2 - Console Transmit Data </div><div>3 - Console Receive Data </div><div>4 - NC </div><div>5 - Gnd </div><div>6 - GPS Receive Data   (to White TXD on - GPS)</div><div>7 - PTT Out   (to Yellow Measurement Pulse output - on GPS)</div>
<div>8 - Gnd    (to Black - on GPS) all appear common - </div><div>9 - NC </div><div> 10 - Console Request To Send (RTS) </div><div> 11 - Console Clear To Send (CTS) </div><div> 12 - NC </div><div> 13 - GPS Power Output (5Vdc @ 800ma MAX) - (Red on - GPS) </div>
<div> 14 - GPS Transmit Data (to green RCV  on - GPS)</div><div> 15 – External Reset </div></div><div><br></div><div><br></div><div>And Yes the gps works fine in windows - not sure what I am missing -</div><div><br></div>
<div><br></div><div><br></div><div class="gmail_extra"><div class="gmail_quote"><br></div></div></div>