<div dir="ltr">I should be asleep, or maybe I am. I just re-read your message and now I see you said that you do have GPS lock so ignore what I said about TX and RX.<div>If you only have that problem when you telnet into the board, I have seen that when I have a poor quality network connection between the pc and the voter board. I think that the board gets too busy with re-sending on the ethernet and then has trouble reading the serial port data from the GPS. If they are on the same LAN then use a switch instead of a hub and make sure that duplex is correct for everything on the LAN segment. Also make sure that your netmask is set correctly (the same) on everything on the LAN.</div><div>Also just go with the default NEMA messages, you do not need any other than the default.</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Sat, Nov 15, 2014 at 12:36 AM, Chuck Henderson <span dir="ltr"><<a href="mailto:rpt2@chuck.midlandsnetworking.com" target="_blank">rpt2@chuck.midlandsnetworking.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr">An easy error is having the TX and RX swapped where you connect the GPS to the voter board. Try it the other way.</div><div class="HOEnZb"><div class="h5"><div class="gmail_extra"><br><div class="gmail_quote">On Sat, Nov 15, 2014 at 12:27 AM, Chuck Henderson <span dir="ltr"><<a href="mailto:rpt2@chuck.midlandsnetworking.com" target="_blank">rpt2@chuck.midlandsnetworking.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr">set the bootloader IP to be the same as the voter board IP, or make it different than anything else on the network. It is the IP that the voter board uses when it is running the bootloader code. It can not have the same IP as your laptop. That will not work.</div><div><div><div class="gmail_extra"><br><div class="gmail_quote">On Sat, Nov 15, 2014 at 12:10 AM, Corey <span dir="ltr"><<a href="mailto:kc7mrq@bresnan.net" target="_blank">kc7mrq@bresnan.net</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><br>
I built a through hole voter board and interfaced it to a GPS 18 LVC and my server. I set the board up as a master, transmit. The LED shows the GPS locked and 98 command shows the GPS,<br>
but I am getting the following error when telnetting into the board:<br>
<br>
Warning: GPS Data time period elapsed.<br>
<br>
The error is timestamped and occurs every second. I made sure the data format was NMEA per archived messages on here by connecting the GPS to SNSRCFG. The config appears to be set up correctly.<br>
What other areas do I need to look at to fix this warning?<br>
<br>
I did notice you can choose quite a few NMEA messages in the SNSRCFG profile. Does it matter if all are checked?<br>
<br>
I have a second issue with updating the firmware. The board is at Rev 1.41. I tried updating it, but haven't had any luck so far. Nothing happens when I click on the "capture target" button after resetting the voter board. The target ip is the voter board and the bootloader ip in the voter is my laptop with ENC_Loader.<br>
<br>
The IC(s) were originally programmed by a friend in another state so I never experienced what it take to do the initial programming.<br>
<br>
<br>
Thanks for your help,<br>
Corey<br>
______________________________<u></u>_________________<br>
App_rpt-users mailing list<br>
<a href="mailto:App_rpt-users@ohnosec.org" target="_blank">App_rpt-users@ohnosec.org</a><br>
<a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/<u></u>mailman/listinfo/app_rpt-users</a><br>
<br>
To unsubscribe from this list please visit <a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/<u></u>mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"<br>
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. </blockquote></div><br></div>
</div></div></blockquote></div><br></div>
</div></div></blockquote></div><br></div>