<div dir="ltr">Lu, <div><br></div><div>This is for a simplex/half duplex link radio but it should be similar to what you're looking for.</div><div><br></div><div>simpleusb.conf</div><div><div>;</div><div>; Usbradio channel driver Configuration File</div><div>;</div><div><br></div><div>[general]</div><div><br></div><div><br></div><div>[usb1968]<span class="" style="white-space:pre"> </span>; Methodist Mountain</div><div><br></div><div>gpio1=in</div><div>hdwtype=0<span class="" style="white-space:pre"> </span>; Leave this set to 0 for USB sound fobs modified using</div><div><span class="" style="white-space:pre"> </span>; the instructions from usbfob.pdf. Use a setting of </div><div><span class="" style="white-space:pre"> </span>; 1 is for Dingotel/Sph interfaces.</div><div> </div><div>rxboost=1<span class="" style="white-space:pre"> </span>; 0 = 20db attenuator inserted, 1= 20db attenuator removed</div><div><span class="" style="white-space:pre"> </span>; Set to 1 for additonal gain if using a low-level receiver output</div><div><br></div><div>rxctcssrelax=1<span class="" style="white-space:pre"> </span>; reduce talkoff from radios w/o CTCSS Tx HPF</div><div><span class="" style="white-space:pre"> </span>; Do not change this, leave this as a 1</div><div><br></div><div>carrierfrom=usbinvert<span class="" style="white-space:pre"> </span>; no,usb,usbinvert,dsp,vox </div><div><span class="" style="white-space:pre"> </span>; no - no carrier detection at all</div><div><span class="" style="white-space:pre"> </span>; usb - from the COR line on the modified USB sound fob</div><div><span class="" style="white-space:pre"> </span>; usbinvert - from the inverted COR line on the modified USB sound fob</div><div><span class="" style="white-space:pre"> </span>; dsp - from RX noise using dsp techniques</div><div><span class="" style="white-space:pre"> </span>; vox - voice activated from RX audio</div><div><br></div><div>ctcssfrom=no<span class="" style="white-space:pre"> </span>; no,usb,dsp</div><div><span class="" style="white-space:pre"> </span>; no - CTCSS decoding, system will be carrier squelch</div><div><span class="" style="white-space:pre"> </span>; usb - CTCSS decoding using input from USB FOB </div><div><span class="" style="white-space:pre"> </span>; (currently not supported)</div><div><span class="" style="white-space:pre"> </span>; dsp - CTCSS decoding using RX audio in DSP.</div><div><span class="" style="white-space:pre"> </span>; rxdemod option must be set to flat for this to work.</div><div><br></div><div>txmixa=voice <span class="" style="white-space:pre"> </span> <span class="" style="white-space:pre"> </span>; Left channel output:no,voice,tone,composite,auxvoice</div><div><span class="" style="white-space:pre"> </span>; no - Do not output anything</div><div><span class="" style="white-space:pre"> </span>; voice - output voice only</div><div><span class="" style="white-space:pre"> </span>; tone - CTCSS tone only</div><div><span class="" style="white-space:pre"> </span>; composite - voice and tone</div><div><span class="" style="white-space:pre"> </span>; auxvoice - auxiliary voice output at headphone level for monitoring</div><div><br></div><div>txmixb=no<span class="" style="white-space:pre"> </span>; Right channel output: no,voice,tone,composite, auxvoice</div><div><span class="" style="white-space:pre"> </span>; See txmixa above.</div><div><br></div><div>invertptt=0<span class="" style="white-space:pre"> </span>; Invert PTT 0 = ground to transmit, 1 = open to transmit</div><div><span class="" style="white-space:pre"> </span>; This is the collector lead of the 2n4401 on the modified</div><div><span class="" style="white-space:pre"> </span>; usb sound fob.</div><div><span class="" style="white-space:pre"> </span>; please refer to the howto for the procedure to do this.</div><div><br></div><div>duplex=0<span class="" style="white-space:pre"> </span>; Full Duplex</div><div><br></div><div>rxondelay=65<span class="" style="white-space:pre"> </span>; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging"</div><div><span class="" style="white-space:pre"> </span>; or "Relay Racing".</div><div><span class="" style="white-space:pre"> </span>; A positive value here will instruct the usbradio driver to ignore the</div><div><span class="" style="white-space:pre"> </span>; COR line for a specified number of 20mSec intervals following the</div><div><span class="" style="white-space:pre"> </span>; release of PTT. Use this only on simplex nodes, and leave commented</div><div><span class="" style="white-space:pre"> </span>; out for repeaters or other full duplex nodes.</div></div><div><br></div><div>rpt.conf</div><div><br></div><div><div>; Radio Repeater configuration file (for use with app_rpt)</div><div>;</div><div> </div><div>[1968]</div><div>rxchannel=SimpleUSB/usb1968</div><div>duplex=1</div><div>;controlstates=controlstates</div><div>scheduler=schedule1968</div><div>functions=functions1968</div><div>phone_functions=functions1968</div><div>;link_functions=functions-remote</div><div>;memory = memory</div><div>;split2m = 600</div><div>;split70cm = 5000</div><div>telemetry=telemetry</div><div>callerid="K0JSC Repeater" <7193150434></div><div>accountcode=RADIO</div><div>idtime=540000</div><div>;ioport = /dev/ttyS0<span class="" style="white-space:pre"> </span>; Serial port for control</div><div>;remote = kenwood<span class="" style="white-space:pre"> </span>; Radio Type</div><div>;dusbabek = yes</div><div>;authlevel = 0<span class="" style="white-space:pre"> </span>; Authorization level </div><div>politeid=30000</div><div>remote_inact_timeout=1800<span class="" style="white-space:pre"> </span>; Inactivity timer for remote base nodes only (set to 0 to disable).</div><div>remote_timeout=3600<span class="" style="white-space:pre"> </span>; Session time out for remote base. (set to 0 to disable)</div><div>;beaconing=0</div><div>;idrecording = |iWZ0N/M<span class="" style="white-space:pre"> </span>; id recording or morse string</div><div>;eannmode=0</div><div>;idtalkover=|iid<span class="" style="white-space:pre"> </span>; Talkover ID (optional) default is none</div><div>;nounkeyct=0</div><div>;holdofftelem=1<span class="" style="white-space:pre"> </span>; Hold off all telemetry when signal is present on receiver or from connected nodes</div><div>telemdynamic=1</div><div>nolocallinkct=1</div><div>linkunkeyct=ct5</div><div>unlinkedct=ct2</div><div>totime=180000</div><div>wait_times=wait-times</div><div>erxgain=-3</div><div>etxgain=3</div><div>context=radio</div><div>;idrecording = /var/lib/asterisk/sounds/rpt/nodenames/1970</div><div>remotect=ct3</div><div>;connpgm=yourconnectprogram<span class="" style="white-space:pre"> </span>; Default: Disabled. Execute a program you specify on connect.</div><div><span class="" style="white-space:pre"> </span>; passes 2 command line arguments to your program: </div><div><span class="" style="white-space:pre"> </span>; 1. node number in this stanza (us)</div><div><span class="" style="white-space:pre"> </span>; 2. node number being connected to us (them)</div><div>;discpgm=yourdisconnectprogram<span class="" style="white-space:pre"> </span>; Default: Disabled. Execute a program you specify on disconnect.</div><div><span class="" style="white-space:pre"> </span>; passes 2 command line arguments to your program: </div><div><span class="" style="white-space:pre"> </span>; 1. node number in this stanza (us)</div><div><span class="" style="white-space:pre"> </span>; 2. node number being disconnected from us (them)</div><div>;lnkactenable=0<span class="" style="white-space:pre"> </span>; Set to 1 to enable the link activity timer. Applicable to standard nodes only.</div><div>;lnkacttime=1800<span class="" style="white-space:pre"> </span>; Link activity timer time in seconds.</div><div>;lnkactmacro=*52<span class="" style="white-space:pre"> </span>; Function to execute when link activity timer expires.</div><div>;lnkacttimerwarn=30seconds<span class="" style="white-space:pre"> </span>; Message to play when the link activity timer has 30 seconds left.</div><div>;</div><div>althangtime=0</div><div>hangtime=0</div><div>telemdefault=2</div><div>events=events1968</div><div><br></div><div>; Morse code parameters, these are common to all repeaters.</div><div><br></div><div>[morse1968]</div><div>speed=20</div><div>frequency=700</div><div>amplitude=2096</div><div>idfrequency=700</div><div>idamplitude=1500</div><div><br></div><div><br></div><div><br></div><div>;</div><div>[functions1968]</div><div>99=cop,6</div><div>989=cop,4</div><div>0=autopatchdn</div><div>6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000<span class="" style="white-space:pre"> </span>; Autopatch up</div><div>83=cop,61,GPIO1=1</div><div>*D0001=f|f|RPT_URI_GPIO1 ;door open</div><div>*D0002=f|t|RPT_URI_GPIO1 ;door closed</div><div>1=ilink,1</div><div>2=ilink,2</div><div>3=ilink,3</div><div>4=ilink,4</div><div>5=macro,3</div><div>70=ilink,5</div><div>71=ilink,6</div><div>72=ilink,7</div><div>73=ilink,15</div><div>74=ilink,16</div><div>75=ilink,8</div><div>80=status,1</div><div>81=status,2</div><div>951=ilink,11 ; Permanent link disconnect</div><div>952=ilink,12 ; Permanent link receive</div><div>953=ilink,13 ; Permanent link transceive</div><div>980=status,3</div><div>;</div><div>;</div><div>[events1968]</div><div>;*D00001=f|f|RPT_URI_GPIO1 ;DOOR OPEN</div><div>;*D00002=f|t|RPT_URI_GPIO1 ;DOOR CLOSED</div><div> </div><div>[macro1967]</div><div>575=*C11 ; call clear wx alerts</div><div>516=*9124<span class="" style="white-space:pre"> </span>;Reboot</div><div>551 = *428299*D50#<span class="" style="white-space:pre"> </span>;Start Master flip script for Normal</div><div>552 = *428299*D51#<span class="" style="white-space:pre"> </span>;Start Master flip script for Net</div><div>553 = *428299*D52# ;Start Master flip script for ARES</div><div>554 = *428299*D53# ;Start Master flip script for Exercise</div><div>555 = *428299*D54# ;Start Master flip script for Skywarn</div><div>560 = *428299*D40#<span class="" style="white-space:pre"> </span> : Start News broadcast</div><div>586 = *82882,*41967*82882#,*41970*82882#,*41971*82882#*41974*82882# ;Send Alert Tones to all nodes</div><div><br></div><div>; Telemetry entries can be shared across all , repeaters or defined for each repeater.</div><div>; Can be a tone sequence, morse string, or a file</div><div>;</div><div>; |t - Tone escape sequence</div><div>;</div><div>; Tone sequences consist of 1 or more 4-tuple entries -freq1, freq2, duration, amplitude-</div><div>; Single frequencies are created by setting freq1 or freq2 to zero.</div><div>;</div><div>; |m - Morse escape sequence</div><div>; </div><div>; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the</div><div>; [morse] section.</div><div>;</div><div>; Follow with an alphanumeric string</div><div>;</div><div>; |i - Morse ID escape sequence</div><div>;</div><div>; Sends Morse code at the ID amplitude and ID frequency as defined in the</div><div>; [morse] section.</div><div>;</div><div>; Follow with an alphanumeric string</div><div><br></div><div>[telemetry]</div><div>ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)</div><div>ct2=|t(660,880,150,2048)</div><div>ct3=|t(440,0,150,4096)</div><div>ct4=|t(550,0,150,2048)</div><div>ct5=|iF</div><div>ct6=|t(880,0,150,2048)</div><div>ct7=|t(660,440,150,2048)</div><div>ct8=|t(600,00,75,1000)(0,0,75,0)(600,0,150,1000)(0,0,75,0)(600,0,75,1000)(0,0,75,0)(600,0,75,1000)</div><div>remotetx=|iK</div><div>remotemon=|t(1209,0,50,2048) </div><div>cmdmode=|t(900,903,200,2048)</div><div>functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)</div><div>patchup=rpt/callproceeding</div><div>patchdown=rpt/callterminated</div><div>; This section allows wait times for telemetry events to be adjusted</div><div>; A section for wait times can be defined for every repeater</div><div>;</div><div><br></div><div>[wait-times]</div><div>telemwait=2000 ; Time to wait before sending most telemetry</div><div>idwait=500 ; Time to wait before starting ID</div><div>unkeywait=1000 ; Time to wait after unkey before sending CTs and link telemetry</div><div>calltermwait=2000 ; Time to wait before announcing "call terminated"</div><div><br></div><div>;</div><div>; This is where you define your nodes which cam be connected to.</div><div>;</div><div><br></div><div>[nodes]</div><div>; Note, if you are using automatic update for allstar link nodes,</div><div>; no allstar link nodes should be defined here. Only place a definition for</div><div>; your local nodes, and private off of allstar link nodes here.</div><div><br></div><div>1968 = <a href="http://radio@127.0.0.1/1968,NONE,y">radio@127.0.0.1/1968,NONE,y</a><span class="" style="white-space:pre"> </span>; This must be changed to your node number</div><div><br></div><div>#includeifexists custom/rpt.conf</div></div><div><br></div><div><br></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Sun, Jun 7, 2015 at 12:05 PM, Lu Vencl <span dir="ltr"><<a href="mailto:luvencl8@gmail.com" target="_blank">luvencl8@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Can somebody send me an example USB file on how you should configure a no that is not running off solely the discriminator processing? I am running discriminator but I am trying to use CTCSS off my repeater. It is tied to pin number seven on the URI, however no matter if I use USB or USB invert I can't seem to get the signaling straightened out. My repeater sends out 12v when CTCSS is detected. I have cor set to no.<br>
Anyone have any ideas or can provide a sample for me please?<br>
<br>
Lu Vencl<br>
_______________________________________________<br>
App_rpt-users mailing list<br>
<a href="mailto:App_rpt-users@ohnosec.org">App_rpt-users@ohnosec.org</a><br>
<a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a><br>
<br>
To unsubscribe from this list please visit <a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"<br>
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.<br>
</blockquote></div><br></div>