<html>
<head>
<style><!--
.hmmessage P
{
margin:0px;
padding:0px
}
body.hmmessage
{
font-size: 12pt;
font-family:Calibri
}
--></style></head>
<body class='hmmessage'><div dir='ltr'><font style="" color="#000000" face="Tahoma,sans-serif">Go into the Asterisk client. Type - asterisk -rvvv - at the Linux prompt. You should see the 'hungup' status when you release the carrier - COR untrue - not when you key. If you are not seeing the hungup command with COS change then there is either something setup wrong or a hardware problem. At least in simpleusb.conf you either set carrierfrom= usb or usbinvert - usb is high +5 COS on signal and usbinvert is low (0V) on signal. It has to be a good low!!! Less than .5 volts and preferably close to 0V in that direction.<br><br>If you can isolate the COS line and connect it to +5 and ground alternately you should see the hungup status in the client. If the logic is backwards the system thinks it is always keyed and will hold all output messages. When you are in that state it can be very confusing because nothing seems to work right. <br id="FontBreak"></font><br><b><font style="font-size:16pt;" size="4">73 Doug</font><font style="font-size:16pt;" size="4"><br></font><font style="font-size:16pt;" size="4">WA3DSP</font><font style="font-size:16pt;" size="4"><br></font><font style="font-size:16pt;" size="4">http://www.crompton.com/hamradio</font></b><font style="font-size:16pt;" size="4"><br></font><br><br><div>> Date: Fri, 26 Jun 2015 22:34:23 -0400<br>> From: w2ibc435@gmail.com<br>> To: app_rpt-users@ohnosec.org<br>> Subject: Re: [App_rpt-users] node issues..<br>> <br>> its new install, and yes it is the DMK URI. and yes repeater is hooked<br>> up.<br>> <br>> receiver COR is active high (+5V when signal is detected) but it is<br>> doing this without any signal from the receiver cor and with signal<br>> from cor. <br>> <br>> in usbradio.conf for COR detect I have tried DSP,USB,USBINVERTED<br>> nothing changes with the output.<br>> <br>> <br>> <br>> <br>> <br>> On Fri, 26 Jun 2015 22:17:31 -0400<br>> Robert Newberry <N1XBM@amsat.org> wrote:<br>> <br>> > Is this a brand new install? Is there a radio hooked to your sound<br>> > card? I've run into this once where the COR pin was active high, thus<br>> > disconnecting the DB25 caused it to think there was a signal on the<br>> > input thus causing PTT. Are you using a DMK URI? Are you getting ptt<br>> > indication?<br>> > <br>> > N1XBM<br>> > Apparare Scientor<br>> > Paratus Communicare<br>> > Allstar Node # 27086, 41540, 41812<br>> <br>> _______________________________________________<br>> App_rpt-users mailing list<br>> App_rpt-users@ohnosec.org<br>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users<br>> <br>> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"<br>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. <br>> <br></div> </div></body>
</html>