<html>
<head>
<style><!--
.hmmessage P
{
margin:0px;
padding:0px
}
body.hmmessage
{
font-size: 12pt;
font-family:Calibri
}
--></style></head>
<body class='hmmessage'><div dir='ltr'><font style="" color="#000000" face="Tahoma,sans-serif">I have never heard DTMF falsing on any node I am involved with and that is many. Not to say it can't happen but if it is happening more that very occasionally then you might have a problem with levels.<br><br>BUT - light bulb went off....<br><br>Also radio_relax should be turned off in the compile of Acid. By default it is turned on. This can be set in makemenu in the asterisk source directory and then asterisk recompiled and reloaded.<br><br>Both the Rpi2 and BBB have had this disabled from the beginning. When it is on muting of the audio due to DTMF falsing is definitely a problem. I don't deal with many Acid nodes and my Acid node has this turned off so I completely forgot about it.<br id="FontBreak"></font><font style="" face="Tahoma,sans-serif"><br></font><font style="" face="Tahoma,sans-serif">Also for message try setting it this way....</font><font style="" face="Tahoma,sans-serif"><br></font><font style="" face="Tahoma,sans-serif"><br></font><font style="" face="Tahoma,sans-serif">holdofftelem=1</font><font style="" face="Tahoma,sans-serif"><br></font><font style="" face="Tahoma,sans-serif">telemdefault=2</font><font style="" face="Tahoma,sans-serif"><br></font><font style="" face="Tahoma,sans-serif"><br></font><font style="" face="Tahoma,sans-serif">in the node definitions in rpt.conf This will allow messages you make at your node but it will mute others after about 30-60 seconds. Again this is the defualt on BBB and RPi2 images from hamvoip.org but not Acid.</font><br><br><b><font style="font-size:16pt;" size="4">73 Doug</font><font style="font-size:16pt;" size="4"><br></font><font style="font-size:16pt;" size="4">WA3DSP</font><font style="font-size:16pt;" size="4"><br></font><font style="font-size:16pt;" size="4">http://www.crompton.com/hamradio</font></b><font style="font-size:16pt;" size="4"><br></font><br><br><div>> Date: Mon, 29 Jun 2015 19:52:58 -0400<br>> From: w2ibc435@gmail.com<br>> To: app_rpt-users@ohnosec.org<br>> Subject: Re: [App_rpt-users] node issues..<br>> <br>> very good, I ended up just muting announcements altogether.<br>> <br>> Audio settings were a bit tricky, ended up having to just experiment<br>> with the settings. now got it where it sounds acceptable to us.<br>> <br>> Now last things to figure out for me now is using a gpio pin on the<br>> URI to trigger the internal pl encoder in the GE, and have it set to<br>> drop 1 second after COS loss from RF and or Internet. <br>> <br>> And to figure out how to turn off DTMF Muting, having a horrid time<br>> with RF users voice falsing the DTMF decoder thus ended up with holes<br>> in the local users transmission. propogate_dtmf=yes don't seem to work<br>> for turning off dtmf mute on local rf<br>> <br>> On Sat, 27 Jun 2015 22:45:59 -0400<br>> mike@midnighteng.com wrote:<br>> <br>> > <br>> > Glad you found it.<br>> > <br>> > Here is how to change connect announcement. In extensions.conf<br>> > example:<br>> > exten => 29283,1,Answer<br>> > exten => 29283,n,Wait(2)<br>> > exten => 29283,n,Playback(rpt/node)<br>> > exten => 29283,n,SayAlpha(kb8jnm)<br>> > exten => 29283,n,Playback(repeater)<br>> > exten => 29283,n,Rpt,29283|P<br>> > <br>> > Chances are that your other inputs are to low if the announcements<br>> > seem to high. Bring inputs up and cut the tx audio. Best served with<br>> > a scope if you have one.<br>> > <br>> > ...mike/kb8jnm<br>> > <br>> > > well we discovered the problem.<br>> > ><br>> > > a broken wire.<br>> > ><br>> > > so it now works, now trying to figure out how to change the<br>> > > connect/disconnect messages from node # to callsign and how to lower<br>> > > the announcement levels without bothering the rx/tx levels<br>> > ><br>> > > On Sat, 27 Jun 2015 19:30:26 -0400<br>> > > Doug Crompton <doug@crompton.com> wrote:<br>> > ><br>> > >> If you have carrierfrom=usb then you should see the hungup status<br>> > >> in the client when you ground pin 8. If you are not you possibly<br>> > >> could possibly have a bad DMK-URI. Make sure you are using pin 8<br>> > >> on the DMK-URI NOT pin 7. Also make sure you have ctcssfrom=no 73<br>> > >> Doug WA3DSP http://www.crompton.com/hamradio<br>> > >><br>> > >><br>> > >> > Date: Sat, 27 Jun 2015 11:20:54 -0400<br>> > >> > From: w2ibc435@gmail.com<br>> > >> > To: doug@crompton.com<br>> > >> > Subject: Re: [App_rpt-users] node issues..<br>> > >> ><br>> > >> > it don't seem to matter what I do on this thing. COR is +5 on<br>> > >> > signal. the thing floats at .7 with no signal. I can force it to<br>> > >> > a ground and the TX still stays locked no messages<br>> > >> ><br>> > >> > carrierfrom=usb is what I am using.<br>> > >> ><br>> > >> > its getting very close to meeting mr 20 pound sledge then going<br>> > >> > to the dump.<br>> > >> ><br>> > >> > On Fri, 26 Jun 2015 23:11:00 -0400<br>> > >> > Doug Crompton <doug@crompton.com> wrote:<br>> > >> ><br>> > >> > > Go into the Asterisk client. Type - asterisk -rvvv - at the<br>> > >> > > Linux prompt. You should see the 'hungup' status when you<br>> > >> > > release the carrier - COR untrue - not when you key. If you<br>> > >> > > are not seeing the hungup command with COS change then there<br>> > >> > > is either something setup wrong or a hardware problem. At<br>> > >> > > least in simpleusb.conf you either set carrierfrom= usb or<br>> > >> > > usbinvert - usb is high +5 COS on signal and usbinvert is<br>> > >> > > low (0V) on signal. It has to be a good low!!! Less than .5<br>> > >> > > volts and preferably close to 0V in that direction.<br>> > >> > ><br>> > >> > > If you can isolate the COS line and connect it to +5 and ground<br>> > >> > > alternately you should see the hungup status in the client. If<br>> > >> > > the logic is backwards the system thinks it is always keyed<br>> > >> > > and will hold all output messages. When you are in that state<br>> > >> > > it can be very confusing because nothing seems to work right.<br>> > >> > > 73 Doug WA3DSP http://www.crompton.com/hamradio<br>> > >> > ><br>> > >> > ><br>> > >> > > > Date: Fri, 26 Jun 2015 22:34:23 -0400<br>> > >> > > > From: w2ibc435@gmail.com<br>> > >> > > > To: app_rpt-users@ohnosec.org<br>> > >> > > > Subject: Re: [App_rpt-users] node issues..<br>> > >> > > ><br>> > >> > > > its new install, and yes it is the DMK URI. and yes repeater<br>> > >> > > > is hooked up.<br>> > >> > > ><br>> > >> > > > receiver COR is active high (+5V when signal is detected) but<br>> > >> > > > it is doing this without any signal from the receiver cor and<br>> > >> > > > with signal from cor.<br>> > >> > > ><br>> > >> > > > in usbradio.conf for COR detect I have tried<br>> > >> > > > DSP,USB,USBINVERTED nothing changes with the output.<br>> > >> > > ><br>> > >> > > ><br>> > >> > > ><br>> > >> > > ><br>> > >> > > ><br>> > >> > > > On Fri, 26 Jun 2015 22:17:31 -0400<br>> > >> > > > Robert Newberry <N1XBM@amsat.org> wrote:<br>> > >> > > ><br>> > >> > > > > Is this a brand new install? Is there a radio hooked to<br>> > >> > > > > your sound card? I've run into this once where the COR pin<br>> > >> > > > > was active high, thus disconnecting the DB25 caused it to<br>> > >> > > > > think there was a signal on the input thus causing PTT.<br>> > >> > > > > Are you using a DMK URI? Are you getting ptt indication?<br>> > >> > > > ><br>> > >> > > > > N1XBM<br>> > >> > > > > Apparare Scientor<br>> > >> > > > > Paratus Communicare<br>> > >> > > > > Allstar Node # 27086, 41540, 41812<br>> > >> > > ><br>> > >> > > > _______________________________________________<br>> > >> > > > App_rpt-users mailing list<br>> > >> > > > App_rpt-users@ohnosec.org<br>> > >> > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users<br>> > >> > > ><br>> > >> > > > To unsubscribe from this list please visit<br>> > >> > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and<br>> > >> > > > scroll down to the bottom of the page. Enter your email<br>> > >> > > > address and press the "Unsubscribe or edit options button"<br>> > >> > > > You do not need a password to unsubscribe, you can do it via<br>> > >> > > > email confirmation. If you have trouble unsubscribing,<br>> > >> > > > please send a message to the list detailing the problem.<br>> > >> > > ><br>> > >> > ><br>> > >> ><br>> > >><br>> > > _______________________________________________<br>> > > App_rpt-users mailing list<br>> > > App_rpt-users@ohnosec.org<br>> > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users<br>> > ><br>> > > To unsubscribe from this list please visit<br>> > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and<br>> > > scroll down to the bottom of the page. Enter your email address and<br>> > > press the "Unsubscribe or edit options button"<br>> > > You do not need a password to unsubscribe, you can do it via email<br>> > > confirmation. If you have trouble unsubscribing, please send a<br>> > > message to the list detailing the problem.<br>> > ><br>> > <br>> > <br>> > _______________________________________________<br>> > App_rpt-users mailing list<br>> > App_rpt-users@ohnosec.org<br>> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users<br>> > <br>> > To unsubscribe from this list please visit<br>> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll<br>> > down to the bottom of the page. Enter your email address and press<br>> > the "Unsubscribe or edit options button" You do not need a password<br>> > to unsubscribe, you can do it via email confirmation. If you have<br>> > trouble unsubscribing, please send a message to the list detailing<br>> > the problem. <br>> <br>> _______________________________________________<br>> App_rpt-users mailing list<br>> App_rpt-users@ohnosec.org<br>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users<br>> <br>> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"<br>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. <br>> <br></div> </div></body>
</html>