<div dir="ltr">Given that the repeaters don't overlap you might benefit to setup simulcast even though you're not syncing the transmitters. Anywhere you do have overlap, like on the ridge tops, you're going to get out of sync signals but I'm guessing that is a low percentage of coverage area. If you could get one transmitter to capture your receiver, even just a little, you should have mostly intelligible reception at those locations. Maybe walking down from the ridge top a little ways. <div><br></div><div>Alternatively, do you have a location that can cover all the ridge tops? Use a different transmit frequency to cover those spots that the psuedo-simulcast causes interference at. Instead of the many different channels you would end up programming and using with separate input tones, you would now have only two, the main channel and the secondary transmitter channel.</div><div><br></div><div>The receiver at this alternate site could be the same frequency and voted, or just have transmit only since the other voted receivers would be providing coverage.</div><div><br></div><div>--------</div><div><br></div><div>Those commands in your linked message look to be easily scripted from an external control script. I haven't played with the RTCM's yet but can you somehow see which site is being voted from the command line? Doesn't AllMon do this? If so it should be relatively easy to watch the voted sites and pick the appropriate transmitter. Might need a little special logic built-in.</div><div><br></div><div>Brett KQ9N</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Mon, Jul 20, 2015 at 3:46 PM, Tom Hayward <span dir="ltr"><<a href="mailto:tom@tomh.us" target="_blank">tom@tomh.us</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><span class="">On Mon, Jul 20, 2015 at 12:54 PM, David McGough <<a href="mailto:kb4fxc@inttek.net">kb4fxc@inttek.net</a>> wrote:<br>
><br>
> Hi Tom,<br>
><br>
</span><span class="">> AllStar nor RTCM's implement this functionality, as far as I know.<br>
<br>
</span>It's not a terribly complex operation, just activating a single<br>
transmitter instead of many. Maybe this configuration could be<br>
adapted:<br>
<a href="http://ohnosec.org/pipermail/app_rpt-users/2015-April/011662.html" rel="noreferrer" target="_blank">http://ohnosec.org/pipermail/app_rpt-users/2015-April/011662.html</a><br>
<span class=""><br>
> Honestly, I'm not sure that this type of system would be a good fit for a<br>
> ham radio repeater system--all it would take is one mischievous Kerchunker<br>
> to greatly impair the systems operation (by "locking out" all but the site<br>
> the Kerchunker is closest to). The Kerchunker might not even realize that<br>
> Emergency Comms were in progress on a distant repeater, which they<br>
> couldn't hear.<br>
><br>
> Just being curious, what kind of repeaters are you currently running, and<br>
> how many, over how big an area?<br>
<br>
</span>We have a few homebrew repeaters with S-COM 7330 controllers. The<br>
transmitters and receivers are various from Motorola and Kenwood. We<br>
would standardize on just one model before implementing voting. We'd<br>
probably eliminate the 7330 too, in favor of just RTCMs and app_rpt.<br>
<br>
We'd like to serve a ring around Mt. Rainier. The area is mostly<br>
wilderness with no inhabitance and deep valleys. There would be almost<br>
no overlap between transmitters--just at the tops of ridges.<br>
<br>
Many similar systems in the region use a different tone for each<br>
repeater. We could do it this way, but I'd prefer to let a computer<br>
make the decision about which site is best.<br>
<div class="HOEnZb"><div class="h5"><br>
Tom KD7LXL<br>
_______________________________________________<br>
App_rpt-users mailing list<br>
<a href="mailto:App_rpt-users@ohnosec.org">App_rpt-users@ohnosec.org</a><br>
<a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" rel="noreferrer" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a><br>
<br>
To unsubscribe from this list please visit <a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" rel="noreferrer" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"<br>
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.<br>
</div></div></blockquote></div><br></div>