<html>
<head>
<meta content="text/html; charset=ISO-8859-1"
http-equiv="Content-Type">
</head>
<body bgcolor="#FFFFFF" text="#000000">
<br>
USB and USBinvert are used only when you are using hardware signals
from the radio to provide cor and CTCSS decode.<br>
<br>
If you are using DSP for Carrierfrom and CTCSSFROM in your
usbradio.conf file then the usb and usbinvert are not used.<br>
<br>
<br>
If you were to use the hardware signals from the radio then you
would select either usb or usbinvert depending the logic signal the
radio provides.<br>
<br>
For example: If you are using carrierfrom=usb then the cor line on
the URI would need to be connected to the cor (or CAS). If the
signal goes to ground with no signal (Squelched) and goes hi
(unsquelched), the URI will see the logic signal and treat it as the
squelch is open. <br>
<br>
If the radio signal goes low WITH a signal (unsquelched) and goes hi
(squelched) then set the carrierfrom to usbinvert. <br>
<br>
So the usb setting is for signals that go hi (Active hi) and
USBinvert is for signals that go low (Active low).<br>
<br>
the same perameters also apply for the CTCSSfrom seting. for this
the CTCSs decode line must also be connected in the URI.<br>
<br>
One other note: <br>
<br>
When using these hardware signals, it is important to know that the
URI hardware detection depends on the transition going to ground and
not providing a voltage. It is possible some radios will provide a
voltage swing with a squelch or tone decode, but not go to ground
when there is no voltage. <br>
<br>
In the Master II, if I remember, the CTCSS decode does go to ground
with the correct tone but does not provide a voltage. For this
connection the usbinvert would work for ctcssfrom. <br>
<br>
But, the CAS is the opposite and provides a voltage when unsquelched
but doesn go to ground when squelched. <br>
<br>
For this reason I alsways installed a NPN transistor to invert the
signal in the radio to provide me with a Active low signal for CAS.
<br>
<br>
Since you are using DSP for Carrierfrom and ctcssfrom, then you can
ignore the hardware signals. <br>
<br>
Hope this helps, <br>
<br>
Jon VA3RQ<br>
<br>
On 9/20/2015 11:16 AM, Robert Newberry wrote:
<blockquote
cite="mid:CAM09xEZda2Y_U2+v86=ubrGRC6+Fc8u9EEHY2hvzLjiPf0ruDQ@mail.gmail.com"
type="cite">
<p dir="ltr">I've gotten a lot of good info. I've got some work to
do to figure this strange noise out.</p>
<p dir="ltr">I do have one question.</p>
<p dir="ltr">Ctcssfrom=dsp is what I use. I currently use a
DMKURI. I've noticed the USB and USBinvert mention using a USB
fob. Can anyone elaborate on the differences of these two?</p>
<p dir="ltr">N1XBM<br>
Apparare Scientor<br>
Paratus Communicare<br>
Allstar Node # 27086, 41540, 41812, 42086<br>
</p>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<br>
<pre wrap="">_______________________________________________
App_rpt-users mailing list
<a class="moz-txt-link-abbreviated" href="mailto:App_rpt-users@ohnosec.org">App_rpt-users@ohnosec.org</a>
<a class="moz-txt-link-freetext" href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a>
To unsubscribe from this list please visit <a class="moz-txt-link-freetext" href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. </pre>
</blockquote>
</body>
</html>