<div dir="ltr">I don't have the test equipment to go through all of the dirty Local Oscilator, SINAD, etc., so I will have to wait on that a few weeks before the president of the club gets back in town. <div><br></div><div>WHEN I bypassed the capacitor and resistor ( 1k and .03µ) , the RTCM was able to calibrate squelch. The LED flashed several times and then was steady. Maybe the capacitor is the wrong value. There was no code on it, but based on the resistor code, the value was correct. </div><div><br></div><div>73</div><div>Skyler</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Mon, Mar 28, 2016 at 4:08 PM, Joe Leikhim <span dir="ltr"><<a href="mailto:rhyolite@leikhim.com" target="_blank">rhyolite@leikhim.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">If you are using an external reference, you cannot make up for the 2nd LO error if it is wildly off. There is an easy SINAD related test in EIA-603 that is called Offset Acceptance Bandwidth that would indicate if the IF were off center. Things that could go wrong apart from simple misalignment of the Quad Detector coil could include the LO crystal being way off frequency, the IF filters being wrong BW or off spec pass frequency.<br>
<br>
Given the symptoms, I am putting my money on a misadjusted quad coil.<span class="HOEnZb"><font color="#888888"><br>
<br>
Joe</font></span><span class="im HOEnZb"><br>
<br>
On 3/28/2016 5:06 PM, Bryan Fields wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
On 3/28/16 2:51 PM, Joe Leikhim wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
1) Make sure the receiver First Local Oscillator is adjusted correctly<br>
on frequency. (Fo -10.700 MHz) Likewise the second LO should be at<br>
around 10.2450 MHz. The second LO is not adjustable, so any minor error<br>
would have to be made up with the TCXO U3. After this second step:<br>
<br>
Then :<br>
<br>
2) Make sure the general alignment is set properly, especially the<br>
discriminator coil T2 which responds to 10.7000 MHz from a signal<br>
generator, has an S curve response.  In my experience with these sort of<br>
Quadrature  Detector chips, you can get a false sense of IF centering<br>
where the noise component is suppressed. You might try adjusting for<br>
maximum noise first without the 10.7000 MHz signal. Be careful you don't<br>
jam the coil slug.<br>
</blockquote>
These are both very good points i didn't consider.  I normally don't check my<br>
reference oscillators in the hamtronics as they are using an external 10MHz<br>
source.<br>
<br>
You will want to check SINAD on it as well, if it's not making spec (and those<br>
hamtronics are very sensitive), something else is wrong with it.<br>
<br>
</blockquote>
<br>
-- <br></span><span class="im HOEnZb">
Joe Leikhim<br>
<br>
<br>
Leikhim and Associates<br>
<br>
Communications Consultants<br>
<br>
Oviedo, Florida<br>
<br>
JLeikhim@Leikhim.com<br>
<br>
<a href="tel:407-982-0446" value="+14079820446" target="_blank">407-982-0446</a><br>
<br>
<a href="http://WWW.LEIKHIM.COM" rel="noreferrer" target="_blank">WWW.LEIKHIM.COM</a><br>
<br></span><div class="HOEnZb"><div class="h5">
_______________________________________________<br>
App_rpt-users mailing list<br>
<a href="mailto:App_rpt-users@ohnosec.org" target="_blank">App_rpt-users@ohnosec.org</a><br>
<a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" rel="noreferrer" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a><br>
<br>
To unsubscribe from this list please visit <a href="http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users" rel="noreferrer" target="_blank">http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"<br>
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. </div></div></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature"><div dir="ltr"><font face="arial narrow, sans-serif" color="#38761d">Skyler Fennell</font><div><font face="arial narrow, sans-serif" color="#38761d"><a href="http://amsatnet.info" target="_blank">amsatnet.info</a></font></div><div><font face="arial narrow, sans-serif" color="#38761d">KDØWHB</font></div><div><font face="arial narrow, sans-serif" color="#38761d"><a href="mailto:electricity440@gmail.com" target="_blank">electricity440@gmail.com</a></font></div></div></div>
</div>