<html>
<head>
<meta content="text/html; charset=utf-8" http-equiv="Content-Type">
</head>
<body bgcolor="#FFFFFF" text="#000000">
<p>Hayden; How are you generating CTCSS tone? <br>
</p>
<br>
<div class="moz-cite-prefix">On 3/13/2017 9:41 PM, Joe Leikhim
wrote:<br>
</div>
<blockquote
cite="mid:1e53fffa-f75b-a939-d343-fe592ae4d06f@leikhim.com"
type="cite">
<meta content="text/html; charset=utf-8" http-equiv="Content-Type">
<p>Wow; <br>
</p>
<p>Great project. I suggest documenting everything and permanently
posting for others to review the system design as a reference.</p>
<p>My background is in Public Safety LMR design so I have dabbled
a bit in VHF, UHF and 800 MHz simulcast both analog and digital.
I might be able to do some computer modelling for you. <br>
</p>
<p>Here is an example, picture two sites x1 and x2 spaced exactly
13 miles apart. <br>
</p>
<p>First: They both need to launch the audio waveform at exactly
the same time T=0 in same phase. This also means that there may
need to be <u>bulk delay</u> to ensure that the most distant
(with respect to the IP back haul network) transmitter site,
receives the entire data payload before it is transmitted. I am
just learning about the RTCM so I believe that bulk delay is
inherent to the process. <br>
</p>
<p>Assuming both sites are exactly synced T=0, then where the wave
fronts meet midway will be in exactly sync even though 35.1us
(6.5 miles x 5.4 us = 35.1 us) has passed due to propagation
delay. <br>
</p>
<p>The wave fronts will also form a pair of theoretical opposing
hyperbolic curves that meet at the center of the two sites like
this: x1 )( x2 with the x representing each site. <br>
</p>
<p>As a mobile travels away from center and along or behind the
hyperbolic curves )(, the time differential will increase,
creating time differential interference (TDI), or intersymbol
interference (ISI) in a digital system. This can be calculated
at any point location by using a map and a mileage scale.<br>
</p>
<p>A mobile very close to or behind either site (paced 13 miles)
will experience the delay of 70.2 us or more. This is somewhat
mitigated by the capture effect of the closest site and the
capture ratio afforded by the modulation index. TDI at 70.2 us
is not too bad for analog FM. 135 us, the distortion might be
intolerable. <br>
</p>
<p>Adding a third site will require consideration that its signal
may arrive earlier or later than the sites described above, In
the event the third site is closer than 6.5 miles, the
adjustment would be to increase the launch delay for the third
site to meet with sites 1 and 2. If it is further than 6.5
miles, the delay of sites 1 and 2 could be increased equally by
the amount required for site 3 to travel.</p>
<p>A variation of this scheme, is one where a central site is
predominant and is ringed by remote sites. In one configuration,
the central site has an omni directional antenna and the remote
sites have directional antennas facing outward. The central site
would be timed to transmit first, and the remote sites would be
delayed until the wavefront reaches them. If the distances are
unequal, the remote sites would be timed +/- the time
differential of the central site reaching them.<br>
</p>
<p>There are a couple very proprietary computer programs for
modeling this, however it can be worked out by hand.</p>
<p>Some thoughts.</p>
<p>1) Don't worry about frequency offset until you are sure the
timing and other parameters are correct. Set everything dead on
with GPS to start. In commercial systems using GPS disciplined
reference frequency offset is usually not performed.<br>
</p>
<p>2) Make 100% sure that the modulators are wired for the same
polarity. It makes no sense to have one transmitter deviating +4
KHz while another is going -4KHz. Same goes for voice and CTCSS
modulation.</p>
<p>3) Are your transmitters the exact same make/model and version?
This can be a non starter. You can get away with different RF
amps, filters etc, but if you have a Micor exciter and a Mastr
II exciter it is going to be funky.</p>
<p>4) The audio chain needs to be identical. Any filters, amps
etc, in the transmitter audio chain must be same at each site.<br>
</p>
<p>5) Adjust the modulation limiting such that the transmitter
audio is never in limiting. For Part 97 work, you could get away
with the limiter adjusted beyond system deviation and set the
RTCM so that deviation is equal to 5 KHz. Voice deviation for
each transmitter must be identical, same with CTCSS.<br>
</p>
<p>For my commercial projects I recommend the entire simulcast
system be staged in a warehouse so that all these parameters can
be set at same time with same test equipment in a controlled
environment. Any errors must track the same direction. You can
do this remotely, but noisy signals will make the setting of
values less than ideal. If you reach a level of frustration,
bring it all home and tweak it.<br>
</p>
I hope this helps!<br>
<br>
<div class="moz-cite-prefix">On 3/13/2017 7:15 PM, Hayden
Honeywood wrote:<br>
</div>
<blockquote
cite="mid:CAC0VLD3XjAnq=j7XQsDOpvcmha5FmD9BORJ8G92EWPXjcVsjQg@mail.gmail.com"
type="cite">
<div dir="ltr">Hi All,
<div>Thanks for all on the list who have given me a hand with
getting the RTCM/voter boards running.</div>
<div><br>
</div>
<div>I currently have 1/3 of my system installed at the sites.
It's as follows:</div>
<div><br>
</div>
<div>A TX only site - running a VOTER board, latest "Chuck"
firmware. 9.6MHz OCXO replacing the onboard crystal and a
10MHz OCXO to keep the transmitter stable all on 53MHz.</div>
<div><br>
</div>
<div>On my bench at home I have an identical setup except with
a receiver in addition. Both radios are the same, audio
injected in the same spot.</div>
<div><br>
</div>
<div>I've been testing various frequency offsets to avoid the
cancelling of the signal due to the inherent propagation
effects at 6 metres. I've been able to run my bench radio
into a dummy load and place it so that another radio nearby
connected to an external antenna is receiving them almost
the same (i.e. overlap). </div>
<div><br>
</div>
<div>Currently 1-2Hz sounds the best. I have been encoding
tone, however there is a very audible hum, as if the CTCSS
tone from each transmitter is not in phase. The tone is
91.5Hz. I've checked/readjusted deviation levels etc, also
checked the 9.6MHz OCXO etc but I cannot seem to null it
out.</div>
<div><br>
</div>
<div>I've also tested the Simulcast Launch Delay.The main site
is about 13 miles away, so I put a value of 330 in there to
represent a delay of 66uS on the bench test radio. This
makes a little bit of improvement, but not an overall huge
improvement. Does anyone have an ideas that I've missed or
more information on the usage of the Simulcast Launch delay?</div>
<div><br>
</div>
<div>Hayden </div>
</div>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<br>
<pre wrap="">_______________________________________________
App_rpt-users mailing list
<a moz-do-not-send="true" class="moz-txt-link-abbreviated" href="mailto:App_rpt-users@lists.allstarlink.org">App_rpt-users@lists.allstarlink.org</a>
<a moz-do-not-send="true" class="moz-txt-link-freetext" href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users">http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users</a>
To unsubscribe from this list please visit <a moz-do-not-send="true" class="moz-txt-link-freetext" href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users">http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. </pre>
</blockquote>
<br>
<pre class="moz-signature" cols="72">--
Joe Leikhim
Leikhim and Associates
Communications Consultants
Oviedo, Florida
<a moz-do-not-send="true" class="moz-txt-link-abbreviated" href="mailto:JLeikhim@Leikhim.com">JLeikhim@Leikhim.com</a>
407-982-0446
<a moz-do-not-send="true" class="moz-txt-link-abbreviated" href="http://WWW.LEIKHIM.COM">WWW.LEIKHIM.COM</a></pre>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<br>
<pre wrap="">_______________________________________________
App_rpt-users mailing list
<a class="moz-txt-link-abbreviated" href="mailto:App_rpt-users@lists.allstarlink.org">App_rpt-users@lists.allstarlink.org</a>
<a class="moz-txt-link-freetext" href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users">http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users</a>
To unsubscribe from this list please visit <a class="moz-txt-link-freetext" href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users">http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. </pre>
</blockquote>
<br>
<pre class="moz-signature" cols="72">--
Joe Leikhim
Leikhim and Associates
Communications Consultants
Oviedo, Florida
<a class="moz-txt-link-abbreviated" href="mailto:JLeikhim@Leikhim.com">JLeikhim@Leikhim.com</a>
407-982-0446
<a class="moz-txt-link-abbreviated" href="http://WWW.LEIKHIM.COM">WWW.LEIKHIM.COM</a></pre>
</body>
</html>