<div dir="ltr"><div class="gmail_default" style="font-size:xx-large">Using the channel driver usbradio, did you run radio-tune-menu and adjust the squelch?<br>It sounds to me, like the squelch is wide open, and you're using usbradio.conf to define the pl tone(s). If your squelch is wide open, you will hear that bit of squelch crash after the tone is dropped, and before the repeater drops.<br><br>There are 2 ways to go on the settings, and I don't remember which is which so there's a 50/50 shot at this... but "as I recall" (and I'm not remembering well, these days) the Lower the number, the 'looser' the squelch. <br><br>For experimentation, you might try turning the tone requirement for the receiver off, and adjusting that value, while listening to the output of the repeater (while not hooked up to anyone) and determine where the squelch level should be.<br><br>best of luck es 73<br>-Geoff/W5OMR (29655)</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Wed, Jun 6, 2018 at 5:37 AM, John W Benedict <span dir="ltr"><<a href="mailto:John@ke5rs.com" target="_blank">John@ke5rs.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div lang="EN-US" link="blue" vlink="purple">
<div class="m_163611607075566894WordSection1">
<p class="MsoNormal">Thank you Chuck and Mike,<u></u><u></u></p>
<p class="MsoNormal"><u></u> <u></u></p>
<p class="MsoNormal">Chuck,<u></u><u></u></p>
<p class="MsoNormal">Yes… I thought USBRadio with more complexity, not simple would be what was needed… I am using pin 9 now from the 15 pin and going to pin 21 at the URIx. I will look at what you show below and see if that is the direction to go. As you
described “Best results”, I will check into grabbing the discriminator audio being a little nervous with my skill set
<span style="font-family:"Segoe UI Emoji",sans-serif">😊</span><u></u><u></u></p>
<p class="MsoNormal"><u></u> <u></u></p>
<p class="MsoNormal">Thank you.<u></u><u></u></p>
<p class="MsoNormal"><u></u> <u></u></p>
<p class="MsoNormal">Mike,<u></u><u></u></p>
<p class="MsoNormal">I did play some with the “rxondelay” but with no luck. What I remember, adding time to “rxondelay “ gave me a short burst of initial audio out the front speaker with more time getting a longer audio burst before it gets muted. This audio
burst would only happen if the squelch tale drops completely from the previous transmission. I did not hear a difference with what was heard on the air from the transmitter including the squelch crash was still present.<u></u><u></u></p>
<p class="MsoNormal"><u></u> <u></u></p>
<p class="MsoNormal">Thank you for your reply…<u></u><u></u></p><span class="">
<p class="MsoNormal" style="margin-right:0in;margin-bottom:18.75pt;margin-left:0in;background:white">
<span style="font-family:"Arial",sans-serif;color:black">John de KE5RS<br>
_._ . ..... ._. ...<u></u><u></u></span></p>
<p class="MsoNormal"><u></u> <u></u></p>
</span><p class="MsoNormal"><b>From:</b> App_rpt-users <<a href="mailto:app_rpt-users-bounces@lists.allstarlink.org" target="_blank">app_rpt-users-bounces@lists.<wbr>allstarlink.org</a>>
<b>On Behalf Of </b>Chuck Henderson<br>
<b>Sent:</b> Tuesday, June 5, 2018 10:45 PM<br>
<b>To:</b> Users of Asterisk app_rpt <<a href="mailto:app_rpt-users@lists.allstarlink.org" target="_blank">app_rpt-users@lists.<wbr>allstarlink.org</a>><br>
<b>Subject:</b> Re: [App_rpt-users] Squelch Tail Crash Elimination<u></u><u></u></p><div><div class="h5">
<p class="MsoNormal"><u></u> <u></u></p>
<div>
<p class="MsoNormal">I think that if you feed direct discriminator audio to the usb interface and use usbradio then it automatically takes care of the necessary delays and avoids loosing any audio in the process. For best results you can grab the direct discriminator
audio from the cable that runs from inside the Receiver Unit to the Filter Unit (shown below), I can't remember if I used the L-in or the R-in. Or second best you can use the DSP processed discriminator output in the DB15 connector (center pin in center row,
pin 8) but it isn't as good and has more delay.<u></u><u></u></p>
<div>
<p class="MsoNormal"><u></u> <u></u></p>
<div>
<div>
<p class="MsoNormal"><img width="425" height="405" style="width:4.427in;height:4.2187in" id="m_163611607075566894_x0000_i1025" src="cid:image002.png@01D3FD53.7BAAA450"><u></u><u></u></p>
</div>
<p class="MsoNormal"><u></u><u></u></p>
</div>
</div>
</div>
<div>
<p class="MsoNormal"><u></u> <u></u></p>
<div>
<p class="MsoNormal">On Tue, Jun 5, 2018 at 9:41 PM, Mike <<a href="mailto:mm@midnighteng.com" target="_blank">mm@midnighteng.com</a>> wrote:<u></u><u></u></p>
<blockquote style="border:none;border-left:solid #cccccc 1.0pt;padding:0in 0in 0in 6.0pt;margin-left:4.8pt;margin-right:0in">
<div>
<p><u></u> <u></u></p>
<p>Well, I don't want to lead you astray... as I'm not for sure on this...<u></u><u></u></p>
<p>Had to think on it a while...<u></u><u></u></p>
<p>You might try adding some time to rxondelay (ms) but I'm not sure that will delay the repeated audio.<u></u><u></u></p>
<p>I think it may only delay the cor activation time.<u></u><u></u></p>
<p>But, if nobody chimes in with the 'right stuff' give it a try. <u></u><u></u></p>
<p>I'm thinkin you might need to create a special audio delay.<u></u><u></u></p>
<p>73,<u></u><u></u></p>
<p>...mike/kb8jnm<u></u><u></u></p>
<div>
<div>
<p class="MsoNormal"><u></u> <u></u></p>
<div>
<p class="MsoNormal">On 6/5/2018 10:10 PM, John W Benedict wrote:<u></u><u></u></p>
</div>
</div>
</div>
<blockquote style="margin-top:5.0pt;margin-bottom:5.0pt">
<div>
<div>
<div>
<p class="MsoNormal">Hello,<u></u><u></u></p>
<p class="MsoNormal"> <u></u><u></u></p>
<p class="MsoNormal">I have ASL running a Dell Slim Form computer all seems to be work quite well, connections, Echolink and local repeater with great audio reports however… I like to know how to eliminate
the squelch crash on the tail maybe adding some milliseconds to the receiver audio?<u></u><u></u></p>
<p class="MsoNormal"> <u></u><u></u></p>
<p class="MsoNormal">The system is a Yaesu DR-1X interfaced with the URIx controller using SimpleUSB in ASL version 20180417
<u></u><u></u></p>
<p class="MsoNormal">The computer: Dell SFF Version 4.9.0-6-amd64 #1 SMP Debian 4.9.88-1+deb9u1 (2018-05-07) x86_64.<u></u><u></u></p>
<p class="MsoNormal"> <u></u><u></u></p>
<p class="MsoNormal">I am very novice with Linux and Asterisk but learning bits and pieces…<u></u><u></u></p>
<p class="MsoNormal"> <u></u><u></u></p>
<p class="MsoNormal">Thank you<u></u><u></u></p>
<p class="MsoNormal" style="margin-bottom:18.75pt;background:white">
<span style="font-family:"Arial",sans-serif;color:black">John de KE5RS <br>
_._ . ..... ._. ...</span><u></u><u></u></p>
<p class="MsoNormal"> <u></u><u></u></p>
</div>
<p class="MsoNormal" style="margin-bottom:12.0pt"><u></u> <u></u></p>
</div>
</div>
<pre>______________________________<wbr>_________________<u></u><u></u></pre>
<pre>App_rpt-users mailing list<u></u><u></u></pre>
<pre><a href="mailto:App_rpt-users@lists.allstarlink.org" target="_blank">App_rpt-users@lists.<wbr>allstarlink.org</a><u></u><u></u></pre>
<pre><a href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://lists.allstarlink.org/<wbr>cgi-bin/mailman/listinfo/app_<wbr>rpt-users</a><u></u><u></u></pre>
<pre><u></u> <u></u></pre>
<pre>To unsubscribe from this list please visit <a href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://lists.allstarlink.org/<wbr>cgi-bin/mailman/listinfo/app_<wbr>rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"<u></u><u></u></pre>
<pre>You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. <u></u><u></u></pre>
</blockquote>
<p class="MsoNormal"><u></u> <u></u></p>
</div>
<p class="MsoNormal"><br>
______________________________<wbr>_________________<br>
App_rpt-users mailing list<br>
<a href="mailto:App_rpt-users@lists.allstarlink.org" target="_blank">App_rpt-users@lists.<wbr>allstarlink.org</a><br>
<a href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">http://lists.allstarlink.org/<wbr>cgi-bin/mailman/listinfo/app_<wbr>rpt-users</a><br>
<br>
To unsubscribe from this list please visit <a href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users" target="_blank">
http://lists.allstarlink.org/<wbr>cgi-bin/mailman/listinfo/app_<wbr>rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"<br>
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
<u></u><u></u></p>
</blockquote>
</div>
<p class="MsoNormal"><u></u> <u></u></p>
</div>
</div></div></div>
</div>
<br>______________________________<wbr>_________________<br>
App_rpt-users mailing list<br>
<a href="mailto:App_rpt-users@lists.allstarlink.org">App_rpt-users@lists.<wbr>allstarlink.org</a><br>
<a href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users" rel="noreferrer" target="_blank">http://lists.allstarlink.org/<wbr>cgi-bin/mailman/listinfo/app_<wbr>rpt-users</a><br>
<br>
To unsubscribe from this list please visit <a href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users" rel="noreferrer" target="_blank">http://lists.allstarlink.org/<wbr>cgi-bin/mailman/listinfo/app_<wbr>rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"<br>
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. <br></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature" data-smartmail="gmail_signature">Operating your AM rig without a scope is like driving our car at night without headlights. (~K4KYV)<br><br>73 = Best Regards,<br>-Geoff/W5OMR</div>
</div>