<html>
<head>
<meta content="text/html; charset=ISO-8859-1"
http-equiv="Content-Type">
</head>
<body bgcolor="#FFFFFF" text="#000000">
All connections good except for the red one in question.<br>
<br>
Change 22 to pin 21 on the FR 5000 and program the I/O pin 21 as an
output. Then assign function "Analog audible" . <br>
set logic to LOW.<br>
<br>
This will give you an analog COR that is active low when the
receiver is active-should you require it.<br>
<br>
Program I/O pin 19 to an input and select "EPTT" as its function and
set the logic to LOW.<br>
<br>
This will make this pin an external ptt.<br>
<br>
In you uri set up set the following:<br>
<br>
[usb1999]<br>
<br>
hdwtype=0 <br>
rxboost=1<br>
txboost=1<br>
rxctcssrelax=1<br>
txctcssdefault=103.5<br>
rxctcssfreqs=103.5<br>
txctcssfreqs=103.5<br>
;rxctcssoverride=0<br>
carrierfrom=dsp<br>
ctcssfrom=dsp<br>
rxdemod=flat<br>
txprelim=no<br>
txlimonly=yes<br>
txtoctype=phase<br>
txmixa=voice<br>
txmixb=no<br>
invertptt=0<br>
duplex=1<br>
rxondelay=0<br>
rxnoisefiltype=0<br>
eeprom=0<br>
plfilter=yes<br>
<br>
This will set you up using dsp for squelch detection and dsp for rx
tone detection. <br>
<br>
This setup requires the Icom to be programmed to transmit the ctcss
tone (if desired). the URI will only send Voice to the Icom.<br>
<br>
Calibrate your RXnoise, RXvoice and RXtone. Then set TX Voice.<br>
<br>
Save your settings.<br>
<br>
If your squelch is open type this at the prompt:<br>
<br>
repeater*CLI> radio tune rxsquelch<br>
Current Signal Strength is 681<br>
Current Squelch setting is 500<br>
<br>
if your squelch setting is below your signal strength, set the
squelch to something about 25 points above the current signal
strength.<br>
<br>
repeater*CLI> radio tune rxsquelch 700<br>
press enter. <br>
<br>
Save settings. <br>
<br>
This set up will require a ctcss tone of 103.5 Hz to access the
receive.<br>
<br>
Also, if you intend to use the allstar node to repeat then set the
channel in the repeater to "duplex" . <br>
This is to ensure the allstar node is repeating and not the Icom.<br>
<br>
Hope this helps. <br>
<br>
Cheers!<br>
<br>
Jon VA3RQ<br>
<br>
<br>
<br>
<br>
<br>
On 12/8/2018 5:50 AM, Lardizabal David D. wrote:
<blockquote
cite="mid:A539441B-7EE8-4510-93E4-D25E06D721D2@yahoo.com"
type="cite">
<meta http-equiv="Content-Type" content="text/html;
charset=ISO-8859-1">
Hi
<div class=""><br class="">
</div>
<div class="">My name is David Lardizabal HQ2DDL. I am trying to
install and AllstarLink node with a repeater Icom FR 5000 and I
am trying to figure out the pinout / setting on repeater. If
anyone has done this setup would appreciate the help.</div>
<div class=""><br class="">
</div>
<div class="">I have all ready have done some testing but I am
getting a lot of noice, like the squelch is open and
transmitting to connected node, ( I am able to connect to other
nodes via line command, I have not been able to get the DTMF
tones to work to connect/disconnect to nodes.)</div>
<div class=""><br class="">
</div>
<div class="">My current pin out is like this: </div>
<div class=""><br class="">
</div>
<div class=""><br class="">
</div>
<div class="">FR 5000 Repeater<span class="Apple-tab-span"
style="white-space:pre"> </span>DML URI</div>
<div class=""><br class="">
</div>
<div class="">7<span class="Apple-tab-span"
style="white-space:pre"> </span>GND <span
class="Apple-tab-span" style="white-space:pre"> </span>=================>
20<span class="Apple-tab-span" style="white-space:pre"> </span>GND</div>
<div class="">8<span class="Apple-tab-span"
style="white-space:pre"> </span>MOD IN
=================> 22<span class="Apple-tab-span"
style="white-space:pre"> </span>TX AUDIO</div>
<div class="">9<span class="Apple-tab-span"
style="white-space:pre"> </span>DISC OUT ================>
21<span class="Apple-tab-span" style="white-space:pre"> </span>RX
AUDIO</div>
<div class="">14<span class="Apple-tab-span"
style="white-space:pre"> </span>GND<span
class="Apple-tab-span" style="white-space:pre"> </span> =================>
19<span class="Apple-tab-span" style="white-space:pre"> </span>GND</div>
<div class="">19<span class="Apple-tab-span"
style="white-space:pre"> </span>PTT<span
class="Apple-tab-span" style="white-space:pre"> </span>=================>
1<span class="Apple-tab-span" style="white-space:pre"> </span>PTT</div>
<div class=""><font class="" color="#ff2600">22<span
class="Apple-tab-span" style="white-space: pre;"> </span>AF
OUT =================> 8<span class="Apple-tab-span"
style="white-space: pre;"> </span>COR DET (?)</font></div>
<div class=""><br class="">
</div>
<div class="">*** as a Note: I found out in a pin out for RTCM
with an ICOM FR6000 repeater;</div>
<div class=""><br class="">
</div>
<div class="">
<pre style="white-space: pre-wrap; background-color: rgb(255, 255, 255);" class="">I recently connected a Micro-Node RTCM to an ICOM FR6000 UHF repeater.
The FR5000/6000 has a DB25 auxiliary connector on the rear.
Here is the sable pin-out I used. Maybe this helps someone else.
FR6000 RTCM
----------------------------------------------------------------------
Pin 11 - 12VDC Out ------------------ Pin 1 +V In
Pin 8 - MOD IN ------------------------- Pin 2 TX Audio
Pin 9 Discriminator ------------------- Pin 3 RX Audio
Pin 21 Analog Audible Out -------- Pin 4 CTCSS In
Pin 14 GND------------------------------ Pin 5 GND
Pin 19 EPTT ---------------------------- Pin 7 PTT
DB25 Shell --- soldered to braid---DB9 Shell
Programming FR6000.
Configured for CTCSS on Receive, no CTCSS on transmit.
Program Pin 21 I/O for Audible Out which is a signal indication when the
receiver is unmuted by squelch/tone.
Program Pin 19 I/O for EPTT - External PTT</pre>
<div class=""><br class="">
</div>
</div>
<div class="">73</div>
<div class=""><br class="">
</div>
<div class="">David</div>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<br>
<pre wrap="">_______________________________________________
App_rpt-users mailing list
<a class="moz-txt-link-abbreviated" href="mailto:App_rpt-users@lists.allstarlink.org">App_rpt-users@lists.allstarlink.org</a>
<a class="moz-txt-link-freetext" href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users">http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users</a>
To unsubscribe from this list please visit <a class="moz-txt-link-freetext" href="http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users">http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users</a> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
</pre>
</blockquote>
</body>
</html>