[FSG-public] Startup issues with DynaDish 5

Edward Erny edwerny at gmail.com
Mon Jan 2 08:30:34 EST 2017


Recently received a new Mikro Tik DynaDish 5 and have not been able to
bring up the configuration page via browser at 192.168.88.1 as the
instructions recommend.

With Bryan's help, I have WinBOX connected via mac address.
In loading the config data, it appears the data is loaded, however several
errors are kicked back, which appear to be systax errors. File attached.

The above two problems might be caused by my unfamiliarity with Mikro Tik
and how it works.  Any ideas or comments would be helpful on getting this
antenna/router working on HamWAN.


Ed Erny

Amateur Radio Call Sign: NZ1Q
St Petersburg Amateur Radio Club <https://www.facebook.com/sparcw4gac/> on
Facebook
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/fsg-public/attachments/20170102/d85361e7/attachment.html>
-------------- next part --------------













  MMM      MMM       KKK                          TTTTTTTTTTT      KKK
  MMMM    MMMM       KKK                          TTTTTTTTTTT      KKK
  MMM MMMM MMM  III  KKK  KKK  RRRRRR     OOOOOO      TTT     III  KKK  KKK
  MMM  MM  MMM  III  KKKKK     RRR  RRR  OOO  OOO     TTT     III  KKKKK
  MMM      MMM  III  KKK KKK   RRRRRR    OOO  OOO     TTT     III  KKK KKK
  MMM      MMM  III  KKK  KKK  RRR  RRR   OOOOOO      TTT     III  KKK  KKK

  MikroTik RouterOS 6.35.4 (c) 1999-2016       http://www.mikrotik.com/

[?]             Gives the list of available commands
command [?]     Gives help on the command and list of arguments

[Tab]           Completes the command/word. If the input is ambiguous,
                a second [Tab] gives possible options

/               Move up to base level
..              Move up one level
/command        Use command at the base level
[admin at MikroTik] > /interface wireless
[admin at MikroTik] /interface wireless> set [ find default-name=wlan1 ] band=5ghz-onlyn channel-width=10m
hz disabled=no \
\... frequency=5180 frequency-mode=superchannel ht-rxchains=0,1 ht-txchains=0,1 \                      
expected end of command (line 2 column 44)
[admin at MikroTik] /interface wireless> l2mtu=2290 mode=station-bridge radio-name=$NZ1Q-StPete scan-list=
HamWAN ssid=HamWAN \
syntax error (line 1 column 6)
[admin at MikroTik] /interface wireless> wireless-protocol=nv2
syntax error (line 1 column 18)
[admin at MikroTik] /interface wireless> /interface vlan
[admin at MikroTik] /interface vlan> add interface=wlan1 l2mtu=2286 name=MGMT-20 vlan-id=20
expected end of command (line 1 column 21)
[admin at MikroTik] /interface vlan> /interface wireless channels
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
0 degrees (north)" \
\... frequency=5920 list=HamWAN name=Sector1-5 width=5                                                 
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
120 degrees (south-east)" \
\... frequency=5900 list=HamWAN name=Sector2-5 width=5                                                 
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
240 degrees (south-west)" \
\... frequency=5880 list=HamWAN name=Sector3-5 width=5                                                 
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
0 degrees (north)" \
\... frequency=5920 list=HamWAN name=Sector1-10 width=10                                               
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
120 degrees (south-east)" \
\... frequency=5900 list=HamWAN name=Sector2-10 width=10                                               
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
240 degrees (south-west)" \
\... frequency=5880 list=HamWAN name=Sector3-10 width=10                                               
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
0 degrees (north)" \
\... frequency=5920 list=HamWAN name=Sector1-5 width=5                                                 
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
120 degrees (south-east)" \
\... frequency=5900 list=HamWAN name=Sector2-5 width=5                                                 
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
240 degrees (south-west)" \
\... frequency=5880 list=HamWAN name=Sector3-5 width=5                                                 
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
0 degrees (north)" \
\... frequency=5920 list=HamWAN name=Sector1-10 width=10                                               
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
120 degrees (south-east)" \
\... frequency=5900 list=HamWAN name=Sector2-10 width=10                                               
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
240 degrees (south-west)" \
\... frequency=5880 list=HamWAN name=Sector3-10 width=10                                               
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
0 degrees (north)" \
\... frequency=5920 list=HamWAN name=Sector1-5 width=5                                                 
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
120 degrees (south-east)" \
\... frequency=5900 list=HamWAN name=Sector2-5 width=5                                                 
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
240 degrees (south-west)" \
\... frequency=5880 list=HamWAN name=Sector3-5 width=5                                                 
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
0 degrees (north)" \
\... frequency=5920 list=HamWAN name=Sector1-10 width=10                                               
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
120 degrees (south-east)" \
\... frequency=5900 list=HamWAN name=Sector2-10 width=10                                               
[admin at MikroTik] /interface wireless channels> add band=5ghz-onlyn comment="Cell sites radiate this at 
240 degrees (south-west)" \
\... frequency=5880 list=HamWAN name=Sector3-10 width=10                                               
[admin at MikroTik] /interface wireless channels> /interface wireless security-profiles
[admin at MikroTik] /interface wireless security-profiles> set [ find default=yes ] supplicant-identity=Mi
kroTik
[admin at MikroTik] /interface wireless security-profiles> /system logging action
[admin at MikroTik] /system logging action> set 3 bsd-syslog=yes remote=44.98.254.1
[admin at MikroTik] /system logging action> /interface bridge port
[admin at MikroTik] /interface bridge port> add bridge=bridge-local interface=ether1
input does not match any value of bridge
[admin at MikroTik] /interface bridge port> add bridge=bridge-local interface=wlan1
input does not match any value of bridge
[admin at MikroTik] /interface bridge port> /ip address 
[admin at MikroTik] /ip address> add address=192.168.88.1/24 comment="default configuration" disabled=yes 
interface=ether1 \
\... network=192.168.88.0                                                                              
[admin at MikroTik] /ip address> /ip dhcp-client
[admin at MikroTik] /ip dhcp-client> add default-route-distance=0 dhcp-options=hostname,clientid disabled=
no interface=MGMT-20
input does not match any value of interface
[admin at MikroTik] /ip dhcp-client> /ip settings
[admin at MikroTik] /ip settings> set ip-forward=no
[admin at MikroTik] /ip settings> /ip upnp
[admin at MikroTik] /ip upnp> set allow-disable-external-interface=no
[admin at MikroTik] /ip upnp> /radius
[admin at MikroTik] /radius> add address=44.98.254.1
[admin at MikroTik] /radius> add address=44.98.254.1 secret=RADIUS-PW-56 service=login
[admin at MikroTik] /radius> /system identity
[admin at MikroTik] /system identity> set name=$NZ1Q
failure: empty identity string
[admin at MikroTik] /system identity> /system leds
[admin at MikroTik] /system leds> set 0 interface=wlan1
[admin at MikroTik] /system leds> /system logging
[admin at MikroTik] /system logging> add action=remote topics=info,warning,critical,firewall,error
[admin at MikroTik] /system logging> add action=remote topics=info,warning,critical,firewall,error
[admin at MikroTik] /system logging> /system ntp client
[admin at MikroTik] /system ntp client> set enabled=yes primary-ntp=104.232.3.3 secondary-ntp=45.127.113.2

[admin at MikroTik] /system ntp client> /system routerboard settings
[admin at MikroTik] /system routerboard settings> set cpu-frequency=600MHz
[admin at MikroTik] /system routerboard settings> /user aaa
[admin at MikroTik] /user aaa> set accounting=yes default-group=read exclude-groups="" interim-update=0s u
se-radius=yes


More information about the FSG-public mailing list