in rpt.conf, (cut and paste ) the [functions] stanza to a seperate file labeled commands.include then delete or comment out all the commands in the stanza and replace with this line "#include commands.include" THEN put all the commands YOU want above and beyond what is required to be standard across everyones nodes 1-5 ilink etc. in the commands.include file. Use (winSCP) to copy the commands.include file to all your nodes and edit each nodes rpt.conf stanza to have the line in [functions] be #include commands.include. For each new system you just you build just add YOUR commands.include file and it will have all the same commands as the others.
..........
............................
and a copy of a generic commands.include file for you to cut and paste if you wish.
;commands.include
;Command common acrossed all nodes
;single digit public commands
0=autopatchdn
1=ilink,1 ; Disconnect Link
2=ilink,2 ; Connect Link MOnitor Only
3=ilink,3 ; Connect Link Transieve
4=ilink,4 ; Enter Command Mode on another Node
5=macro,1 ; Macro Prefix
6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
;double digit public commands
70=ilink,5 ; System Status
71=ilink,6 ; Disconnect all Links
72=ilink,7 ; Play Last Node to Key Up
73=ilink,15 ; FULL system Status - all nodes
74=ilink,16 ; Reconnect disconnected links disconnected with disconnect all links command
75=ilink,8 ; Connect Link LOCAL monitor only
76=
77=
78=
79=
80=status,11 ;Force ID LOCAL ONLY
81=status,12 ; GIve Time of Day LOCAL ONLY
82=status,3 ; Give Software Verison
83=status,5 ; Last DTMF User
84=cop,32 ; DTMF TEST
85=
86=
87=
88=cop,55 ;Parrot Once if parrot mode is disabled
89=autopatchup,context=command_process,noct=1,farenddisconnect=1,dialtime=7000,quiet=1; Command Processing
99=cop,6 ; ptt phone mode
; Triple digit control operator /owner codes
900=cop,3 ;disable system
901=cop,2 ;enable system
903=cop,1 ;System warm boot
902=
903=
904=cop,4 ;Test Tone On/Off
905=cop,5 ;dump system variables
906=
907=cop,7 ;Time out timer enable
908=cop,8 ;Time out timer disable
909=cop,9 ;Autopatch enable
910=cop,10 ;Autopatch disable
911=cop,11 ;Link enable
912=cop,12 ;Link disable
913=cop,13 ;Query System State
914=cop,14 ;Change System State
915=cop,15 ;Scheduler Enable
916=cop,16 ;Scheduler Disable
917=cop,17 ;User functions (time, id, etc) enable
918=cop,18 ;User functions (time, id, etc) disable
919=cop,19 ;Select alternate hang timer
920=cop,20 ;Select standard hang timer
921=cop,21 ;Enable Parrot Mode
922=cop,22 ;Disable Parrot Mode
923=cop,23 ;Birdbath (Current Parrot Cleanup/Flush)
924=cop,24 ;Flush all telemetry
925=cop,25 ;Query !!!!last node un-keyed!!!!
926=cop,26 ;Query all nodes keyed/unkeyed
927=cop,27 ;Reset DAQ minimum on a pin
928=cop,28 ;Reset DAQ maximum on a pin
929=
930=cop,30 ;Recall Memory Setting in Attached Xcvr
931=cop,31 ;Channel Selector for Parallel Programmed Xcvr
932=
933=cop,33 ;Local Telemetry Output Enable
934=cop,34 ;Local Telemetry Output Disable
935=cop,35 ;Local Telemetry Output on Demand
936=cop,36 ;Foreign Link Local Output Path Enable
937=cop,37 ;Foreign Link Local Output Path Disable
938=cop,38 ;Foreign Link Local Output Path Follows Local Telemetry
939=cop,39 ;Foreign Link Local Output Path on Demand
940=cop,40 ;IRLP announce Enable
941=cop,41 ;IRLP announce Disable
942=cop,42 ;Echolink announce node # only
943=cop,43 ;Echolink announce node Callsign only
944=cop,44 ;Echolink announce node # & Callsign
945=cop,45 ;Link Activity timer enable
946=cop,46 ;Link Activity timer disable
947=cop,47 ;Reset "Link Config Changed" Flag
948=cop,48 ;Send Page-Tone specs separated by ( )
949=cop,49 ;Disable incoming connections (control state NOICE)
950=cop,50 ;Enable incoming connections (control state NOICD)
951=cop,51 ;Enable sleep mode
952=cop,52 ;Disable sleep mode
953=cop,53 ;Wake up from sleep
954=cop,54 ;Go to sleep
955=cop,60 ;SEND MDC-1200 Burst
956=cop,56 ;Rx CTCSS Enable
957=cop,57 ;Rx CTCSS Disable
958=cop,58 ;Tx CTCSS On Input only Enable
959=cop,59 ;Tx CTCSS On Input only Disable
; 98 series up to local nodes