Lu,
 
Not sure if you actually got everything answered but from the command line this is how you would do it...
 
Lets say I am node 2337 and I want to control 2340.
 
First I would connect to the node  rpt fun 2337 *32340
 
From 2337 I would issue  rpt fun 2337 *42340  (THis forces all the command sent on 2337 to forward over to 2340)
 
I would then get the audio file telling me it was working.  Then I would just issues commands as normal in the same fashion.  Say I wanted to connect 2340 to the Wan repeater system.  I would issue  rpt fun 2337 *32135.  This would be controlling node 2340.  It will continue to do so until I issue the #.  (rpt fun 2337 #)
 
Corey N3FE
 
 
From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] On Behalf Of Lu Vencl [vencl@att.net]
Sent: Wednesday, July 27, 2011 11:09 PM
To: Ken
Cc: <app_rpt-users@ohnosec.org>
Subject: Re: [App_rpt-users] Remote commands

It was my bad. I did not realize that I had to be actually connected to the node first. I thought you could control without being connected. 

Sent from my iPhone, Lu Vencl

On Jul 27, 2011, at 9:29 PM, "Ken" <ke2n@cs.com> wrote:

Yes – once you hear the announcement, it should work. If it is working, the machine you are talking to will stay continuously keyed up.

 

If the machine you are trying to command is not in the right command state (user functions disabled, for example) that would likely block you from executing anything.

 

Ken

 

PS: I replaced the recording with a much nicer sounding one J

 

 

From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Neal Garbenis
Sent: Wednesday, July 27, 2011 9:24 PM
To: Lu Vencl
Cc: <app_rpt-users@ohnosec.org>
Subject: Re: [App_rpt-users] Remote commands

 

Lu

 

Yes I did have a typo sorry. Once you have control everything should work.  

 

Neal

Sent from my iPhone


On Jul 27, 2011, at 9:15 PM, "Lu Vencl" <vencl@att.net> wrote:

Neal, I think you have a typo below.. Should it not be *4XXXXXX?

That is what I have to do to get the remote command back.. Once I have control, I tried *3xxxxx to connect a node , or even *81 to force time announce, but neither work.

So I presume there is a permissions issue or something else I am doing wrong?

 

From: Neal Garbenis [mailto:njgarbenis@gmail.com]
Sent: Wednesday, July 27, 2011 9:08 PM
To: Lu Vencl
Cc: <app_rpt-users@ohnosec.org>
Subject: Re: [App_rpt-users] Remote commands

 

Lu

 

I am no expert but I do use the remote command often. First you need to be connected to the node that you want to control. Then dial *xxxxxx (the node you want to control).  You will then hear a very overdriven audio file that says remote command.   From that point on you are controlling that node you can (connect,disconnect, etc). To exit remote comand mode hit the # sign. 

 

Hope this helps

Neal

NG8Y


Sent from my iPhone


On Jul 27, 2011, at 8:52 PM, "Lu Vencl" <vencl@att.net> wrote:

Ok,

I know this is a newbie question, but I searched everywhere I know and I can’t find an example nor figure this out..

I need to understand the proper command structure or procedure of *4 remote command.

Example, I want to issue a command to one of my nodes from another node. How do I do this?

 

I tried the following example from my node 27870

KA4EPS-R-Margate*CLI> rpt fun 27870 *427869*81#

 

I thought that this command would allow me to announce the time on node 27869 while entering this on the 27870 node..

Is this not possible?

 

Another example, let’s say I want 27869 to connect to 27875 would I want to dial over the air on (node 27870)  *427869*327875#  ?

Thanks again for your help.. I am just not getting anywhere with it.

Lu, KA4EPS

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users


--
This message was scanned and is believed to be clean.
Click here to report this message as spam.