Hi
 
I believe I only enabled the COR.
 
it would seem that I should find a older computer perhaps.
 
Chris

From: Pierre Martel <petem001@hotmail.com>
To: C B <harvard5362@yahoo.com>
Sent: Sunday, August 25, 2013 1:37 PM
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1

I had the same problem and was suspecting dsp.
 
I did un update to latest svn. and was stillg etting same thing.
 
Are you using any dsp on your node? ctcss decoding, cor, ect?
 
 
From: C B
Sent: Sunday, August 25, 2013 2:10 PM
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1
 
Hi
 
I did what you suggested and it seems to complete without error.
 
However it did not resolve the problem.
 
I ran the same commands for Asterisk, still the same issue.
 
Reran the Zaptel compile / install again and still no luck.
 
I re-downloaded for the allstarlink.org the ISO for ACID in case what I downloaded originally was corrupt.
 
after reinstalling I looked at the /root/acid­install.log and I did not see anything that looked like an error.
 
Am I forgetting something or could my hardware not be combatable?
 
As part of this project I did install this successfully on a different computer.
 
Any help greatly appreciated.
 
Chris
 
From: Paul J. Agamata <Sysman@Xceptions.COM>
To: C B <harvard5362@yahoo.com>
Sent: Saturday, August 24, 2013 4:57 PM
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1
 
Log into your 'root' account and navigate to the 'zaptel' directory.
 
When your in there type the following:
 
./configure <enter>
make <enter>
make install <enter>
 
Then reboot your computer and everything should be fine.

_______________________________
Paul J. Agamata
WH6FM
 
From: C B <harvard5362@yahoo.com>
Reply-To: C B <harvard5362@yahoo.com>
Date: Saturday, August 24, 2013 1:54 PM
To: Paul Agamata <Sysman@Xceptions.COM>
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1
 
Paul
 
Please excuse my lack knowledge here, I am very unsure of the compile / install procedure you are speaking of.
 
is there anything you can refer me to that will contain instructions on how to do this?
 
Is it something I did wrong?
 
Sorry for not having a lot of experience.
 
And thank you for your help.
 
Chris
 
From: Paul J. Agamata <Sysman@Xceptions.COM>
To: C B <harvard5362@yahoo.com>; "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Sent: Saturday, August 24, 2013 4:46 PM
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1
 
This is indicative of the zaptel drivers not in your kernel.  Compile/Install then reboot and all should be well.  The 'zaptel' directory is in the 'asterisk' source directory.
 
Be aware that if you update your kernel you will need to re-install the zaptel modules.
 
Regards,
Paul
 

_______________________________
Paul J. Agamata
WH6FM
 
From: C B <harvard5362@yahoo.com>
Date: Saturday, August 24, 2013 1:23 PM
To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Subject: [App_rpt-users] Asterisk ended with exit status 1
 
Hi
 
I am attempting to build a ACID node.
 
After several attempts of reinstalling the ACID with the same results I am asking for some help.
 
All seems to complete normally, I download the configuration, reboot and the following error message keeps repeating.
 
mpg123: no process killed
Asterisk ended with exit status 1
Asterisk died with code 1
Automatically restarting Asterisk
 
Computer is a HPdc5700 small form factor
1 GIG memory
500 GB SATA HDD
 
than you in advance for any help
 
Chris
 




_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users