If this is your usb radio.conf file then it is missing a couple of things.
You need the following:
carrierfrom=usb (or usbinvert if your cor is active low)
and the rxdemod must be set to speaker or flat
That should get tit listening to rx audio to start.
Jon VA3RQ
On 2/8/2014 5:31 PM, ea8ee wrote:eeprom=1rxnoisefiltype=0rxondelay=oduplex=0invertptt=0txmixb=compositetxmixa=compositetxtoctype=notonetxlimonly=notxprelim=norxdemod=noctcssfrom=usb;rxctcssoverride=0rxctcssfreqs=88.5txctcssdefault=88.5rxctcssrelax=1txboost=1usb27305rxboost=1
The DMK works nice in TX but in RX not receive nothing
2014-02-08 20:02 GMT+00:00 Doug Crompton <doug@crompton.com>:
I think it found your adapter as you said you had audio in one direction. If not see below.
Did you select the active usb device in the config utility before you tried to make changes?
If the adapter is not being found at all try this....
The following USB interfaces are defined in usbradio -
#define C108_VENDOR_ID 0x0d8c
#define C108_PRODUCT_ID 0x000c
#define C108AH_PRODUCT_ID 0x013c
#define C119_PRODUCT_ID 0x0008
#define C119A_PRODUCT_ID 0x013a
#define N1KDO_PRODUCT_ID 0x6a00
#define C108_HID_INTERFACE 3
When you boot up you should see one of these initialized in the messages. After boot do -
dmesg | more
and page through and see if it found your adapter.
I am using the DMK and it looks like this -
[root@WA3DSP_Allstar wa3dsp]# dmesg | grep Sound
input: C-Media Electronics Inc. USB PnP Sound Device as /class/input/input0
input,hidraw0: USB HID v1.00 Device [C-Media Electronics Inc. USB PnP Sound Device] on usb-0000:00:1d.0-1
From: ea8ee1@gmail.com
Date: Sat, 8 Feb 2014 19:14:56 +0000
To: app_rpt-users@ohnosec.org
Subject: Re: [App_rpt-users] audio radio to internet issue
I tried with cli and radio tune rxnoise and the pc says the device usb27305 currectly not active ! any suggestion?
2014-02-08 8:51 GMT+00:00 jose <ea8ee1@gmail.com>:
Hi Doug! the ptt and audio from internet to radio works nicely the problem is about the audio from radio to internet not audio neither the node receive the dmtf from radio or webstransceiver
El 08/02/2014 6:31, Doug Crompton escribió:
You need to set -
duplex=1 ; Simplex, no telelmetry
duplex=0 ; Simplex, telelmetry
in rpt.conf if you are running simplex.
Also make sure the polarity is correct in your usbradio or simpleusb file for the PTT and COS if you are using it.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.