Any ideas Jim?
Monty
Mine too, exact same situation. I have to drop the power supply on the G7 to reset it. That's not conducive to "mountain top" operation so it's still on the bench.K0JSCOn Wed, Jun 12, 2013 at 12:36 PM, Kirk <wb6egr@gmail.com> wrote:
Thats not whats occuring with mine, the radio actually goes dark or stops answering the controller. Sometimes it will continue to TX/RX on the last frequency.... *2 *3 makes no differance
Sent from my piece of Crap I-Phone... I feel a Samsung 4 is in my near futureTry this, as it has been working for me for a while.
Instead of connecting to the remote base with a *3 connect with a *2. You should be able to control the radio until the cows come home. Then do a *3 to talk on the specific channel. I have found that as soon as the radio TXs I am unable to control it any more.
Also I find the once I can’t control the G707 any more I do a *1 and disconnect then a *2 again and all is well again.
I’ve been meaning to talk to Jim about this bug..
Scott
From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Jeff Carrier
Sent: Wednesday, June 12, 2013 1:15 AM
To: Monty
Cc: app_rpt mailing list; K&R Yoksh
Subject: Re: [App_rpt-users] G707 Remote Base Locking Up on URI
I have the same issue. First with a home brew interface so I searched hi and low for the "actual" interface board with the same issue as Kirk describes.
De k0jsc
On Jun 11, 2013 9:41 PM, "Monty" <monty@ke7jvx.com> wrote:
Hi Kyle,
I fixed the syntax error, still no joy. I did have a usbradio node and the 707 on simpleusb, so I migrated the 707 to usbradio and removed all the simpleusb configs, still no joy. Any other ideas?
Monty
On Tue, Jun 11, 2013 at 6:42 PM, K&R Yoksh <yokshs@gmail.com> wrote:
Hello Monty,
While not specific to the remote operation, I see one thing that might make app_rpt lose it's mind.
The rxchannel parameter is very picky about syntax, especially the upper and lower case letters. The correct format is:
rxchannel=SimpleUSB/usb1010
Another thing I've learned is to never (NEVER) have usbradio.conf and simpleusb.conf exist in /etc/asterisk at the same time. This will
confuse app_rpt at the least, or crash it altogether.
73,
Kyle Yoksh
K0KN
Olathe, KS
Allstar 2210-2219
--- Original Message ---Hello Everyone,
I have tried two Kenwood G707s with three of Jim's URI Adapter cards and
two URIs on two different computers. I am able to get three or four
commands (freq, pl tone, etc) then I will get Allison saying "Invalid
Frequency" and the CLI shows:
"WARNING[7925]: app_rpt.c:13876 serial_remote_io: -99999 Serial device not
responding on node 1010"
The radio will not steer or accept commands anymore until I power cycle the
707. The after power cycle three or four commands and will not steer
again. I have tried the same computer with a VHF Syntor with an xcat and
will accept every command without issue. Also one of my 707s now lives on
a Quad PCI card and steers with every command without issue. Has anyone
else seen this or know the remedy? Below is my rpt.conf with the URI:
[1010]
archivedir=/etc/asterisk/qso
rxchannel = simpleusb/usb1010
duplex=0
ioport = /dev/ttyS0
remote = kenwood
authlevel = 1
memory=memory
remote_inact_timeout=5400
remote_timeout=5400
functions=remote-functions
phone_functions=remote-functions
link_functions=remote-functions_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users