Hi Mike, thanks for the reply. Right now the carrierfrom is set to DSP. I am not sure if that is correct or not. The radio (Maxon sm2544 data radio) I am using has audio noise all the time at the input when no signal is there and my audio when key my handheld and talk to it.

I will check the tone issue as I believe I tried a couple of different selections and yes it did set the tone to 100 at allstar. I don’t need tone I believe as the transmitter generates it. On the receive end it is listening to a repeater that is also generating tone back if I want it. I tried changing the rxtone to that tone the repeater had as well and nothing.

I will check the carrier issue and tones again though.

Oh, I did unplug the URI and plug it back in as well. Even went so far as to reinstall ACID all over again.

My configuration is for a remote base transmitting to a repeater so we can offer a alstar link to it if that gives anyone an idea.

Thanks Steve N4YZA

From: mike@midnighteng.com

Sent: Friday, May 17, 2013 9:48 AM

To: app_rpt-users@ohnosec.org

Subject: Re: [App_rpt-users] A problem I am having

I'm sure you will get a few reply's but just on the surface I would ask is

-Do you have CTCSS set a tone as opposed to NO ?

rxctcssfreqs=no

I think by default the acid install sets it to 100.0 ? but i'm not sure.

Also in usbradio.conf

Make sure your input logic is correct (don't use mine but here are some options)

carrierfrom =

;carrierfrom=no
;carrierfrom=dsp
;carrierfrom=pp
carrierfrom=ppinvert
;carrierfrom=usb
;carrierfrom=usbinvert
;carrierfrom=vox

ctcssfrom=dsp

Your usb dongle may be stuck. remove it for a second and plug it back in same place.

Make sure it assigns the same position as you have described.

I have a few that get stuck and replaced them. not sure why but it does happen.

...mike/kb8jnm

29283

-------- Original Message --------
Subject: [App_rpt-users] A problem I am having
From: "The Rices" <srice3@cfl.rr.com>
Date: Fri, May 17, 2013 8:45 am
To: <app_rpt-users@ohnosec.org>

I am brand new to this and have been reading to see if I can find a solution to the problem I am having.

I purchased a URI and installed it with no problems.

I set up the computer using acid and it accepted the node and server info and seems to come on line fine.

When I connect using allstar it connects to the radio and announces it I am connected.

When I use the computer microphone I can hear it come out on the radio fine.

BUT when I go to listen there is no audio coming back over the link from the radio.

I checked with a scope to be sure I had audio and I do.

I ran the radio adjustments for rxnoise and rx voice and it said everything was successful.

It did have me adjust the squelch higher though.

I made sure to open the 2 ports ssh and the udp so I don’t think it is a port issue on the router.

I am sure it is something simple but I am not sure where to look next.

Any helpful suggestions for a beginner would be appreciated.

Thanks Steve

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

No virus found in this message.
Checked by AVG - www.avg.com
Version: 2013.0.3336 / Virus Database: 3162/6331 - Release Date: 05/17/13