Hi
 
tried this and no luck.
 
I updated the BIOS no luck.
 
I am lost.
 
thank you
 
Chris
From: Jeff Carrier <k0jsc.jeff@gmail.com>
To: C B <harvard5362@yahoo.com>
Sent: Sunday, August 25, 2013 11:20 AM
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1

I normally do this when I see this issue.  I have a node that has the error frequently. 
 
  1. Remove the old source tree, grab the source tarball and uncompress into a new source tree, build it, and install it:
    cd /usr/src
rm -rf astsrc-old
mv astsrc astsrc-old
wget http://x.allstarlink.org/svn-trunk.tar.gz -O- | tar xzv
mv trunk astsrc
cd astsrc
make upgrade-acid
  2. Restart asterisk 
    astres.sh
73 de K0JSC
 
On Sun, Aug 25, 2013 at 12:10 PM, C B <harvard5362@yahoo.com> wrote:
Hi
 
I did what you suggested and it seems to complete without error.
 
However it did not resolve the problem.
 
I ran the same commands for Asterisk, still the same issue.
 
Reran the Zaptel compile / install again and still no luck.
 
I re-downloaded for the allstarlink.org the ISO for ACID in case what I downloaded originally was corrupt.
 
after reinstalling I looked at the /root/acid­install.log and I did not see anything that looked like an error.
 
Am I forgetting something or could my hardware not be combatable?
 
As part of this project I did install this successfully on a different computer.
 
Any help greatly appreciated.
 
Chris

From: Paul J. Agamata <Sysman@Xceptions.COM>
To: C B <harvard5362@yahoo.com>
Sent: Saturday, August 24, 2013 4:57 PM
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1

Log into your 'root' account and navigate to the 'zaptel' directory.

When your in there type the following:

./configure <enter>
make <enter>
make install <enter>

Then reboot your computer and everything should be fine.

_______________________________
Paul J. Agamata
WH6FM

From: C B <harvard5362@yahoo.com>
Reply-To: C B <harvard5362@yahoo.com>
Date: Saturday, August 24, 2013 1:54 PM
To: Paul Agamata <Sysman@Xceptions.COM>
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1

Paul
 
Please excuse my lack knowledge here, I am very unsure of the compile / install procedure you are speaking of.
 
is there anything you can refer me to that will contain instructions on how to do this?
 
Is it something I did wrong?
 
Sorry for not having a lot of experience.
 
And thank you for your help.
 
Chris

From: Paul J. Agamata <Sysman@Xceptions.COM>
To: C B <harvard5362@yahoo.com>; "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Sent: Saturday, August 24, 2013 4:46 PM
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1

This is indicative of the zaptel drivers not in your kernel.  Compile/Install then reboot and all should be well.  The 'zaptel' directory is in the 'asterisk' source directory.

Be aware that if you update your kernel you will need to re-install the zaptel modules.

Regards,
Paul


_______________________________
Paul J. Agamata
WH6FM

From: C B <harvard5362@yahoo.com>
Date: Saturday, August 24, 2013 1:23 PM
To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Subject: [App_rpt-users] Asterisk ended with exit status 1

Hi
 
I am attempting to build a ACID node.
 
After several attempts of reinstalling the ACID with the same results I am asking for some help.
 
All seems to complete normally, I download the configuration, reboot and the following error message keeps repeating.
 
mpg123: no process killed
Asterisk ended with exit status 1
Asterisk died with code 1
Automatically restarting Asterisk
 
Computer is a HPdc5700 small form factor
1 GIG memory
500 GB SATA HDD
 
than you in advance for any help
 
Chris
 





_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users