We are using other gtx900.They are not that sensible, but with a repeater at a good spot it works pretty good._______________________________________________Le sam. 6 juil. 2019 à 10:16, Bryan D. Boyle <bdboyle@bdboyle.com> a écrit :what he was asking is what hardware you’re going to use to receive @902 MHZ?_______________________________________________The GTX is beyond being stone deaf at that frequency, so if you were planning to use one as a receiver, you will not be receiving anything.It’s pretty hard to build a cheap radio (and the GTX is a cheap radio, considering) with 25 MHZ of bandwidth between shared components on the board.--BryanSent from my iPhone 6S...No electrons were harmed in the sending of this message.902.400rx 927.400 txLe sam. 6 juil. 2019 à 08:57, Kirk Just Kirk <wb6egr@gmail.com> a écrit :What are you going to use a a RCVR (902.xxxx) Mhz?_______________________________________________On Sat, Jul 6, 2019 at 5:48 AM Pierre Martel <petem001@gmail.com> wrote:Thats in the to do list. But I want to have it interfaced properly before doing this. Cause if I cant get those radio running good with allstarlink, I wont mess with the rest of the mods.._______________________________________________Le sam. 6 juil. 2019 à 02:05, Kirk Just Kirk <wb6egr@gmail.com> a écrit :Make SURE you do the power control mod!!!!!! These radios do stupid things...like 2 watts one time and 18 the next time. They run hot. NOT a good choice for a Node radio.On Fri, Jul 5, 2019 at 9:20 PM Pierre Martel <petem001@gmail.com> wrote:Hello to the group, Got a pair of GTX900 mobile radio and got them tuned (mostly ok) to the ham band.I now want to use them for repeater use in the 900 mhz band.I went to repeater builder page and used all the info I could for the interfacing.I did went for flat audio connection, as stated on the gtx900 page I used pin 7 and 11 for the receiver audio out. And I did put the dip switch close to the interfacing jack to off as specified. I then tried to do a radio tune rxnoise but it always fail. I want to use the dsp fonction of usbradio as it is way easier then getting a cor output on the gtx900.Anyone ever used those radio with ASL?thanksVE2PF______________________________________________________________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.