----- Original Message -----

From: Bryan D. Boyle

To: Mike Wolthuis

Cc: <app_rpt-users@ohnosec.org>

Sent: Monday, September 17, 2012 7:12 PM

Subject: Re: [App_rpt-users] TX Tone Drop out Time

only if, in a subdirectory called 'custom' in /etc/asterisk, you created a file called usbradio.conf.  in other words, no, you don't uncomment it if you haven't.

--

Bryan

Sent from my iPhone

please forgive misspellings...

On Sep 17, 2012, at 18:56, "Mike Wolthuis" <wolthuis@gmail.com> wrote:

I tried to put the following two lines into my beagle.conf

txtoctype=notone

txctcssdefault=131.8

Now there is a line in the beagle.conf that says:

#includeifexists custom/usbradio.conf

However, as you see it is commented out.

Should those two lines have an effect out of beagle.conf or do I need to add usbradio.conf and remove the uncomment #?

Thanks,

Mike

Kb8zgl

From: Ken [mailto:ke2n@cs.com]
Sent: Sunday, September 16, 2012 12:15 PM
To: 'Mike Wolthuis'; app_rpt-users@ohnosec.org
Subject: RE: [App_rpt-users] TX Tone Drop out Time

Beagle board uses chan_simpleusb

So the config file is:  simpleusb.conf

Allegedly it supports the same encoding functions.

See:

http://ohnosec.org/pipermail/app_rpt-users/2011-February/002275.html

Ken

From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Mike Wolthuis
Sent: Sunday, September 16, 2012 9:52 AM
To: app_rpt-users@ohnosec.org
Subject: Re: [App_rpt-users] TX Tone Drop out Time

Does this work on a Beagle board also do you know?

Mike

Kb8zgl

From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Ken
Sent: Sunday, September 16, 2012 7:55 AM
To: 'Jim W7RY'; app_rpt-users@ohnosec.org
Subject: Re: [App_rpt-users] TX Tone Drop out Time

This is in usbradio.conf

txtoctype=notone     ; Transmit tone control type: no,phase,notone

                     ; no - CTCSS tone encoding with no hang time

                     ; phase - encode CTCSS and reverse phase

                     ; AKA ("reverse burst") before unkeying TX

                     ; notone - encode CTCSS and stop sending tone before unkeying TX

                     ; AKA ("chicken burst")

If you select notone (as shown here), then the PL drops about 600 ms before the carrier drops.

Most people like it that way ;-)

Ken

From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Jim W7RY
Sent: Sunday, September 16, 2012 12:05 AM
To: app_rpt-users@ohnosec.org
Subject: [App_rpt-users] TX Tone Drop out Time

I had my PL tone encoder (node generated) drop out before the carrier dropped out. It seems to have quit working. The PL generator is working fine, but the timing seems to changed.  I don’t seem to find the command now. I'm probably not be looking in the right file.

Can someone please tell me where that setting is?

Thanks!

73

Jim W7RY

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users