Copied and pasted a line [radio-gui], changed
the node number on the left, but not the right.... it was 1 digit off like the
example below. And to think I went over it many times trying to figure out what
I did incorrectly. (sigh!)
[radio-gui]
exten => [node1],1,rpt([node1]|X)
exten => [node2],1,rpt([node1]|X)
Thanks,
Bob
kk6ecm
From: app_rpt-users-bounces@ohnosec.org
[mailto:app_rpt-users-bounces@ohnosec.org] On
Behalf Of REDBUTTON_CTRL
Sent: Sunday, April 06, 2014 5:10
AM
To: app_rpt-users@ohnosec.org
Subject: Re: [App_rpt-users]
iaxrpt
We didn't see what the reply was. What was the typo???
inquiring minds want to know.
You should be able to set up 2 separate accounts in IAX_rpt and connect to each
node separately if you have all the settings in you server right.
in iax.conf:
; Setup for remote gui console
[gui]
type=user
context=radio-gui
auth=md5
secret=something ; your password used in iax_rpt accounts
host=dynamic
disallow=all
allow=ulaw
allow=gsm
notransfer=yes
in extensions.conf:
; Setup for IAX_RPT gui console
[radio-gui]
exten => [node1],1,rpt([node1]|X)
exten => [node2],1,rpt([node2]|X)
note: "[node1]" = your first node# on the server and
"[node2]" is the second node.
Then make sure you have 2 accounts defined in IAX_Rpt, one for each node.
In this case both accounts will use the same password.
That should allow you to connect to either node and command it independently.
Hope this helps.
Regards,
Jon VA3RQ
On 4/6/2014 12:29 AM, Bob wrote:
Thanks Mike... root cause, typo (sigh!) I
may be getting smarter on this stuff... still a lousy typist.
Bob
--------
Original Message --------
Subject: [App_rpt-users] iaxrpt
From: "Bob" <kk6ecm@gmail.com>
Date: Sun, April 06, 2014 12:01 am
To: <app_rpt-users@ohnosec.org>
When I put my two nodes located on a single server
into iaxrpt, and separately connect to each, both activate the first node URI
trasmit LED when I “TRANSMIT” from either in iaxrpt; the node under
[radio-secure-proxy]. I have both nodes “register=”ed in iax.conf
under [general] and as “exten => “ under [radio-secure].
[radio-secure-proxy], and “exten =*” under [radio-gui] in extensions.conf.
Did I do something incorrectly, or is this a
limitation of iax and iaxrp? I’d like to independently connect to either
node on the server from iaxrpt.
By the way, under CLI, I can selectively activate,
adjust, and identify either URI, so I’m sure I don’t have any USB
confusion.
_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
and scroll down to the bottom of the page. Enter your email address and press
the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email
confirmation. If you have trouble unsubscribing, please send a message to the
list detailing the problem.
_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.