Send App_rpt-users mailing list submissions to
    app_rpt-users@ohnosec.org

To subscribe or unsubscribe via the World Wide Web, visit
    http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
or, via email, send a message with subject or body 'help' to
    app_rpt-users-request@ohnosec.org

You can reach the person managing the list at
    app_rpt-users-owner@ohnosec.org

When replying, please edit your Subject line so it is more specific
than "Re: Contents of App_rpt-users digest..."


Today's Topics:

  1. Re: Hamtronics receiver issue with AllStar RTCM (Chuck Henderson)
  2. How to add chan_rtpdir.c to DIAL (Michael J. Wolthuis)


----------------------------------------------------------------------

Message: 1
Date: Sat, 2 Apr 2016 16:06:16 -0500
From: Chuck Henderson <rpt2@chuck.midlandsnetworking.com>
To: Skyler F <electricity440@gmail.com>
Cc: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Subject: Re: [App_rpt-users] Hamtronics receiver issue with AllStar
    RTCM
Message-ID:
    <CADEYVwhCSq8vx+g58i8tZVHGM5P6CvKsAiq2QeHqPmXzefFLKw@mail.gmail.com>
Content-Type: text/plain; charset="utf-8"

"Once you have verified that the firmware is running, place a jumper shunt
on JP8 and JP10. Be sure to
do this at a reasonable human room temperature (like 60-80 deg. F). This is
necessary because this
procedure initializes the operating parameters in the EEPROM and also does
a *temperature compensation*
*diode calibration* which needs to happen at room temperature. Once the
jumper shunts
have been installed, power-cycle the board and wait for the system activity
light to come on steady
(about 4 seconds or so after the 5 second initial wait time). Then remove
the jumper shunts."

>From https://allstarlink.org/votersystem.pdf page 20
Chuck


On Sat, Apr 2, 2016 at 3:23 PM, Skyler F <electricity440@gmail.com> wrote:

> Well stupid me for not listening to you guys. I guess the hamtronics is
> really sensitive to low impedance outputs, and the highs get cut off if you
> have any sort of load at all. When I turned on the internal amplifier, the
> RTCM was happy with calibrating squelch.
>
> Can anybody explain to me what "Diode calibration" means?
>
> 73,
> Skyler
>
> On Wed, Mar 30, 2016 at 5:42 PM, Joe Leikhim <rhyolite@leikhim.com> wrote:
>
>> Skyler;
>>
>> Here is a wideband VHF 136-156 MHz radio that will solve your ham club
>> problems for $35 each. If these were UHF I would be buying a bushel full.
>> You will need to get the programming software from Ritron. I think it is
>> free.
>>
>> There are similar models with an enclosure, but for much more $$.
>>
>> See the auction below on E-Bay:
>>
>> Seller dale575
>>
>> Ritron VHF Transceiver PCA, 136-156MHZ, 5 Watt, Model DTX-142-GCWD-I
>>
>>
>> http://www.ebay.com/itm/Ritron-VHF-Transceiver-PCA-136-156MHZ-5-Watt-Model-DTX-142-GCWD-I/191557457767?_trksid=p2047675.c100005.m1851&_trkparms=aid%3D222007%26algo%3DSIC.MBE%26ao%3D1%26asc%3D35389%26meid%3D4bbbffc700cc4aefba654c3ce0d394f8%26pid%3D100005%26rk%3D2%26rkt%3D6%26sd%3D401085025343
>>
>>
>>
>> On 3/30/2016 12:11 PM, Skyler F wrote:
>>
>> Factory tuned from the factory. And I don't even have a signal generator
>> / counter good for RF. We got one hamtronics board, and won't buy another
>> until we get this one working.
>>
>> On Wed, Mar 30, 2016 at 10:08 AM, Joe Leikhim <rhyolite@leikhim.com>
>> wrote:
>>
>>> Were these receivers factory built and tuned or did individual club
>>> members build them? Either way, you might try others from the lot. If you
>>> have only a rudimentary signal generator and / or frequency counter,
>>> perhaps I can walk you through some "field expedient" steps over the phone.
>>>
>>>
>>> On 3/30/2016 12:01 PM, Skyler F wrote:
>>>
>>> I don't have the test equipment to go through all of the dirty Local
>>> Oscilator, SINAD, etc., so I will have to wait on that a few weeks before
>>> the president of the club gets back in town.
>>>
>>> WHEN I bypassed the capacitor and resistor ( 1k and .03?) , the RTCM was
>>> able to calibrate squelch. The LED flashed several times and then was
>>> steady. Maybe the capacitor is the wrong value. There was no code on it,
>>> but based on the resistor code, the value was correct.
>>>
>>> 73
>>> Skyler
>>>
>>> On Mon, Mar 28, 2016 at 4:08 PM, Joe Leikhim < <rhyolite@leikhim.com>
>>> rhyolite@leikhim.com> wrote:
>>>
>>>> If you are using an external reference, you cannot make up for the 2nd
>>>> LO error if it is wildly off. There is an easy SINAD related test in
>>>> EIA-603 that is called Offset Acceptance Bandwidth that would indicate if
>>>> the IF were off center. Things that could go wrong apart from simple
>>>> misalignment of the Quad Detector coil could include the LO crystal being
>>>> way off frequency, the IF filters being wrong BW or off spec pass frequency.
>>>>
>>>> Given the symptoms, I am putting my money on a misadjusted quad coil.
>>>>
>>>> Joe
>>>>
>>>> On 3/28/2016 5:06 PM, Bryan Fields wrote:
>>>>
>>>>> On 3/28/16 2:51 PM, Joe Leikhim wrote:
>>>>>
>>>>>> 1) Make sure the receiver First Local Oscillator is adjusted correctly
>>>>>> on frequency. (Fo -10.700 MHz) Likewise the second LO should be at
>>>>>> around 10.2450 MHz. The second LO is not adjustable, so any minor
>>>>>> error
>>>>>> would have to be made up with the TCXO U3. After this second step:
>>>>>>
>>>>>> Then :
>>>>>>
>>>>>> 2) Make sure the general alignment is set properly, especially the
>>>>>> discriminator coil T2 which responds to 10.7000 MHz from a signal
>>>>>> generator, has an S curve response.  In my experience with these sort
>>>>>> of
>>>>>> Quadrature  Detector chips, you can get a false sense of IF centering
>>>>>> where the noise component is suppressed. You might try adjusting for
>>>>>> maximum noise first without the 10.7000 MHz signal. Be careful you
>>>>>> don't
>>>>>> jam the coil slug.
>>>>>>
>>>>> These are both very good points i didn't consider.  I normally don't
>>>>> check my
>>>>> reference oscillators in the hamtronics as they are using an external
>>>>> 10MHz
>>>>> source.
>>>>>
>>>>> You will want to check SINAD on it as well, if it's not making spec
>>>>> (and those
>>>>> hamtronics are very sensitive), something else is wrong with it.
>>>>>
>>>>>
>>>> --
>>>> Joe Leikhim
>>>>
>>>>
>>>> Leikhim and Associates
>>>>
>>>> Communications Consultants
>>>>
>>>> Oviedo, Florida
>>>>
>>>> JLeikhim@Leikhim.com
>>>>
>>>> 407-982-0446
>>>>
>>>> WWW.LEIKHIM.COM
>>>>
>>>> _______________________________________________
>>>> App_rpt-users mailing list
>>>> App_rpt-users@ohnosec.org
>>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>>
>>>> To unsubscribe from this list please visit
>>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll
>>>> down to the bottom of the page. Enter your email address and press the
>>>> "Unsubscribe or edit options button"
>>>> You do not need a password to unsubscribe, you can do it via email
>>>> confirmation. If you have trouble unsubscribing, please send a message to
>>>> the list detailing the problem.
>>>>
>>>
>>>
>>>
>>> --
>>> Skyler Fennell
>>> amsatnet.info
>>> KD?WHB
>>> electricity440@gmail.com
>>>
>>>
>>> --
>>> Joe Leikhim
>>>
>>>
>>> Leikhim and Associates
>>>
>>> Communications Consultants
>>>
>>> Oviedo, Florida
>>> JLeikhim@Leikhim.com
>>> 407-982-0446
>>> WWW.LEIKHIM.COM
>>>
>>>
>>
>>
>> --
>> Skyler Fennell
>> amsatnet.info
>> KD?WHB
>> <electricity440@gmail.com>electricity440@gmail.com
>>
>>
>> --
>> Joe Leikhim
>>
>>
>> Leikhim and Associates
>>
>> Communications Consultants
>>
>> Oviedo, Florida
>> JLeikhim@Leikhim.com
>> 407-982-0446
>> WWW.LEIKHIM.COM
>>
>>
>
>
> --
> Skyler Fennell
> amsatnet.info
> KD?WHB
> electricity440@gmail.com
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users@ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
> to the bottom of the page. Enter your email address and press the
> "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://ohnosec.org/pipermail/app_rpt-users/attachments/20160402/bd80bec4/attachment-0001.html>

------------------------------

Message: 2
Date: Sat, 02 Apr 2016 21:07:42 -0400
From: "Michael J. Wolthuis" <wolthuis@gmail.com>
To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Subject: [App_rpt-users] How to add chan_rtpdir.c to DIAL
Message-ID: <0426FF03-B422-471B-A684-7F9BF8307E2B@gmail.com>
Content-Type: text/plain; charset="utf-8"

I am finally replacing a very old install of ACID at a HUB site with DIAL.

This site does have some ties though to rtpDir_tm which is older, but still fun and working?

I can?t seem to get chan_rtpdir.c to compile into Asterisk.  I put it in the channels folder and recompiled, but it acts like it didn?t add it / compile it in.

[Apr  2 21:02:37] NOTICE[1305] app_rpt.c: Normal Repeater Init  2363   

[Apr  2 21:02:37] NOTICE[1305] app_rpt.c: Normal Repeater Init  1000   

[Apr  2 21:02:37] WARNING[1318] channel.c: No channel type registered for 'rtpdir'

[Apr  2 21:02:38] WARNING[1305] app_rpt.c: rpt_thread restarted on node 2363

[Apr  2 21:02:38] WARNING[1305] app_rpt.c: rpt_thread restarted on node 1000

[Apr  2 21:02:38] WARNING[1322] channel.c: No channel type registered for 'rtpdir'

[Apr  2 21:02:40] NOTICE[1305] app_rpt.c: RPT thread restarted on 2363

[Apr  2 21:02:40] WARNING[1305] app_rpt.c: rpt_thread restarted on node 2363

[Apr  2 21:02:40] NOTICE[1305] app_rpt.c: RPT thread restarted on 1000

[Apr  2 21:02:40] WARNING[1305] app_rpt.c: rpt_thread restarted on node 1000



Anyone have any suggestions?
Mike
kb8zgl


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://ohnosec.org/pipermail/app_rpt-users/attachments/20160402/31e04fc1/attachment.html>

------------------------------

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users


End of App_rpt-users Digest, Vol 86, Issue 5
********************************************