2  - VOTER Server Address (FQDN) (voter-demo.allstarlink.org)

3  - VOTER Server Port (667),  4  - Local Port (Override) (0)

5  - Client Password (rptnopl),  6  - Host Password (rptnopl)

7  - Tx Buffer Length (3000)

8  - GPS Data Protocol (0=NMEA, 1=TSIP) (0)

9  - GPS Serial Polarity (0=Non-Inverted, 1=Inverted) (0)

10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (2)

11 - GPS Baud Rate (4800)

12 - External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted) (1)

13 - COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver) (1)

14 - Debug Level (9)

15  - Alt. VOTER Server Address (FQDN) ()

16  - Alt. VOTER Server Port (Override) (0)

17  - DSP/BEW Mode NOT SUPPORTED

18 - "Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs) (0)

19 - Simulcast Launch Delay (0) (approx 200 ns, 5 = 1us, > 0 to ENA SC)

97 - RX Level,  98 - Status,  99 - Save Values to EEPROM

i - IP Parameters menu, o - Offline Mode Parameters menu

q - Disconnect Remote Console Session, r - reboot system, d - diagnostics

Enter Selection (1-27,97-99,r,q,d) : <System Time Not Set>  Using Primary Voter Host (72.0.177.212)

<System Time Not Set>  Voter Host DNS Resolved to 96.36.57.202

<System Time Not Set>  Connection Using Voter Host (96.36.57.202)

<System Time Not Set>  Using Primary Voter Host (96.36.57.202)

Select the following Diagnostic functions:

1  - Set Initial Tone Level (and assert PTT)

2  - Display Value of DIP Switches

3  - Flash LED's in sequence

4  - Run entire diag suite

c  - Show Diagnostic Cable Pinouts

x -  Exit Diagnostic Menu (back to main menu)

q - Disconnect Remote Console Session, r - reboot system

Enter Selection (1-4,c,x,q,r) : 4^M

 

Running Diagnostics...

Testing PTT/External CTCSS

Error - Failed to read PTT/CTCSS in un-asserted state

Testing GPS UART

Error - Failed to read data from GPS UART

Testing level at 100 Hz for Normal Audio

^C

Select the following Diagnostic functions:

--- No the LED's do not come on for GPS/HST

rechecked the wiring all looks right 

assuming GTX is transmit that goes to the GPS rx line and vice versa

GPPS pin 7 is labeled as PTT out in the documentation - not sure what that means, I thought it was Gps 1pps?

http://206.212.254.21/unode_docs/rtcm_%20manual.pdf

P2 - DB15F D-Shell connector for the RS-232 (console @57600 bps, DCE) and GPS 

1 - NC 

2 - Console Transmit Data 

3 - Console Receive Data 

4 - NC 

5 - Gnd 

6 - GPS Receive Data   (to White TXD on - GPS)

7 - PTT Out   (to Yellow Measurement Pulse output - on GPS)

8 - Gnd    (to Black - on GPS) all appear common - 

9 - NC 

 10 - Console Request To Send (RTS) 

 11 - Console Clear To Send (CTS) 

 12 - NC 

 13 - GPS Power Output (5Vdc @ 800ma MAX) - (Red on - GPS) 

 14 - GPS Transmit Data (to green RCV  on - GPS)

 15 – External Reset 

And Yes the gps works fine in windows - not sure what I am missing -

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.