Updated BIOS to latest and no help.

Chris

From: Ken <ke2n@cs.com>
To: 'C B' <harvard5362@yahoo.com>; 'Paul J. Agamata' <Sysman@Xceptions.COM>; app_rpt-users@ohnosec.org
Sent: Sunday, August 25, 2013 11:27 AM
Subject: RE: [App_rpt-users] Asterisk ended with exit status 1

Maybe your PC needs a BIOS update …

http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?prodSeriesId=3249646&objectID=c01039267

Not saying you have this *particular* issue, but if yours is an older one, it might be worth a try…

Ken

From: C B [mailto:harvard5362@yahoo.com]
Sent: Sunday, August 25, 2013 2:11 PM
To: Paul J. Agamata; app_rpt-users@ohnosec.org
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1

I did what you suggested and it seems to complete without error.

However it did not resolve the problem.

I ran the same commands for Asterisk, still the same issue.

Reran the Zaptel compile / install again and still no luck.

I re-downloaded for the allstarlink.org the ISO for ACID in case what I downloaded originally was corrupt.

after reinstalling I looked at the /root/acidinstall.log and I did not see anything that looked like an error.

Am I forgetting something or could my hardware not be combatable?

As part of this project I did install this successfully on a different computer.

Any help greatly appreciated.

Chris

From: Paul J. Agamata <Sysman@Xceptions.COM>
To: C B <harvard5362@yahoo.com>
Sent: Saturday, August 24, 2013 4:57 PM
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1

Log into your 'root' account and navigate to the 'zaptel' directory.

When your in there type the following:

./configure <enter>

make <enter>

make install <enter>

Then reboot your computer and everything should be fine.

_______________________________
Paul J. Agamata

WH6FM

Sysman@Xceptions.COM
Hilo, Hawaii

From: C B <harvard5362@yahoo.com>
Reply-To: C B <harvard5362@yahoo.com>
Date: Saturday, August 24, 2013 1:54 PM
To: Paul Agamata <Sysman@Xceptions.COM>
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1

Paul

Please excuse my lack knowledge here, I am very unsure of the compile / install procedure you are speaking of.

is there anything you can refer me to that will contain instructions on how to do this?

Is it something I did wrong?

Sorry for not having a lot of experience.

And thank you for your help.

Chris

From: Paul J. Agamata <Sysman@Xceptions.COM>
To: C B <harvard5362@yahoo.com>; "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Sent: Saturday, August 24, 2013 4:46 PM
Subject: Re: [App_rpt-users] Asterisk ended with exit status 1

This is indicative of the zaptel drivers not in your kernel. Compile/Install then reboot and all should be well. The 'zaptel' directory is in the 'asterisk' source directory.

Be aware that if you update your kernel you will need to re-install the zaptel modules.

Regards,

Paul

_______________________________
Paul J. Agamata

WH6FM

Sysman@Xceptions.COM
Hilo, Hawaii

From: C B <harvard5362@yahoo.com>
Date: Saturday, August 24, 2013 1:23 PM
To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Subject: [App_rpt-users] Asterisk ended with exit status 1

I am attempting to build a ACID node.

After several attempts of reinstalling the ACID with the same results I am asking for some help.

All seems to complete normally, I download the configuration, reboot and the following error message keeps repeating.

mpg123: no process killed

Asterisk ended with exit status 1

Asterisk died with code 1

Automatically restarting Asterisk

Computer is a HPdc5700 small form factor

1 GIG memory

500 GB SATA HDD

than you in advance for any help

Chris